Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.10
RM3090E _55 Steering _008773 STEERING COLUMN _0049279 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


C195844N16
1.76,0.76 2.094,1.01 0.333,0.25 1.833,0.802 2.083,1 0.25,0.198 10 G5

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item

*: except Manual Transaxle

G5-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G5-3 (IGE) - G5-1 (GND) Input LG - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever is in P*

·

Steering lock unlocked in advance by carrying key and turning engine switch on (IG)

·

After above condition met, engine switch turned off


Pulse generation
(see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G5-4 (SLP1) - G5-1 (GND) Output LG - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.2 V
Entry&Start
·

Push Start Error

·

Sensor Value


G5-5 (LIN) - G5-1 (GND) Input/Output G - W-B LIN communication line - -
Entry&Start

Steering Lock Start Cond


G5-6 (IG2) - G5-1 (GND) Input P - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator assembly) Engine switch off → Engine switch on (IG) Below 1 V → 11 to 14 V
Entry&Start

Ignition Switch


G5-7 (B) - Body ground Input L - Body ground Power source Always 11 to 14 V -

NOTICE:

There are 1 motor and 2 sensors built into the steering lock actuator assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P (except Manual Transaxle).

·

To lock the steering, turn the engine switch off with the shift lever in P (except Manual Transaxle), and then open a door.




i.
C221561C31
0.229,0.417 1.635,0.583 1.406,0.167 1.521,1.594 2.385,1.719 0.865,0.125 2.281,0.469 2.708,0.625 0.427,0.156 1.698,1.729 1.781,2.01 1.781,2.01 1.875,2.01 false 1.542,0.406 2.656,0.167 2.656,0.167 2.948,0.167 false 2.656,0.167 2.469,0.469 false 2.938,1.594 3.302,1.74 0.365,0.146 10 GND 1.896,1.948 2.24,2.104 0.344,0.156 10 *b 3.021,0.104 3.385,0.333 0.365,0.229 10 *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

Noise, chattering, etc. are not shown.


Item Content
Tester Connection G5-3 (IGE) - G5-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating