Home › Engine / Hybrid System › 2AD-FTV COOLING › COOLING FAN SYSTEM(w/ Towing Package) › from 2015.10
RM3090E _51 Engine / Hybrid System _008373 2AD-FTV COOLING _0233584 COOLING FAN SYSTEM(w/ Towing Package) J

2AD-FTV COOLING  COOLING FAN SYSTEM(w/ Towing Package)  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECUs to regulate the cooling fans. The cooling fan ECUs control each cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECUs, achieving both high cooling performance and quietness.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

e.

Check the operation of the cooling fans while operating them using the GTS.

OK:
Tester Operation Fan Operation
100% Cooling fans operate
0% Cooling fans stop



Result:
Result Proceed to
OK A
NG (Fan does not operate) B
NG (No. 2 fan does not operate) C
NG (Fan does not stop) D
NG (No. 2 fan does not stop) E



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK COOLING FAN SYSTEM

C

10.CHECK COOLING FAN SYSTEM

D

18.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - ECM)

E

20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - ECM)
2.CHECK COOLING FAN SYSTEM
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check the operation of the cooling fan.

OK:

The cooling fan operates.



Result:
Proceed to
OK
NG



OK

REPLACE ECM

Click here ENGINE CONTROL (2AD-FTV) > ECM > REMOVAL


NG

3.INSPECT COOLING FAN MOTOR
3.INSPECT COOLING FAN MOTOR
a.

Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (COOLING FAN ECU POWER SOURCE)

NG

4.CHECK TERMINAL VOLTAGE (COOLING FAN ECU POWER SOURCE)
A327844C11
0.271,0.927 0.698,1.219 0.427,0.292 0.979,1.75 1.302,1.188 true 2.396,1.76 2.135,1.208 true 0.354,0.99 0.813,1.188 0.458,0.198 10 false A93 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.833,1.792 1.292,1.99 0.458,0.198 10 false +B1 2.354,1.802 2.813,2 0.458,0.198 10 false E1
*a Front view of wire harness connector
(to Cooling Fan ECU)


a.

Disconnect the cooling fan ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A93-1 (+B1) - A93-3 (E1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - ECM)
a.

Disconnect the cooling fan ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A93-2 (SI) or A61-49 (RFC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COOLING FAN ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A93-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FAN NO. 1 RELAY
a.

Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)

NG

REPLACE FAN NO. 1 RELAY

8.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)
A327845C02
0.927,0.51 1.24,0.667 0.313,0.156 10 false *1 0.208,2.198 0.521,2.354 0.313,0.156 10 false *2
*1 No. 2 engine room relay block and junction block assembly
*2 FAN NO. 1 Relay


a.

Remove the FAN NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V
1 (FAN NO. 1 relay) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - COOLING FAN ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - COOLING FAN ECU)
a.

Remove the FAN NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (FAN NO. 1 relay) - A93-1 (+B1) Always Below 1 Ω
5 (FAN NO. 1 relay) or A93-1 (+B1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK COOLING FAN SYSTEM
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check the operation of the No. 2 cooling fan.

OK:

The No. 2 cooling fan operates.



Result:
Proceed to
OK
NG



OK

REPLACE ECM

Click here ENGINE CONTROL (2AD-FTV) > ECM > REMOVAL


NG

11.INSPECT NO. 2 COOLING FAN MOTOR
11.INSPECT NO. 2 COOLING FAN MOTOR
a.

Inspect the No. 2 cooling fan motor.

Click hereEngine / Hybrid System>2AD-FTV COOLING>COOLING FAN MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (NO. 2 COOLING FAN ECU POWER SOURCE)

NG

REPLACE NO. 2 COOLING FAN MOTOR

12.CHECK TERMINAL VOLTAGE (NO. 2 COOLING FAN ECU POWER SOURCE)
A327844C12
0.271,1.083 0.667,1.302 0.396,0.219 0.979,1.75 1.302,1.188 true 2.396,1.76 2.135,1.208 true 0.344,1.115 0.802,1.313 0.458,0.198 10 false A99 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.823,1.792 1.281,1.99 0.458,0.198 10 false +B2 2.313,1.813 2.771,2.01 0.458,0.198 10 false E2
*a Front view of wire harness connector
(to No. 2 Cooling Fan ECU)


a.

Disconnect the No. 2 cooling fan ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A99-1 (+B2) - A99-3 (E2) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - BODY GROUND)
13.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - ECM)
a.

Disconnect the No. 2 cooling fan ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (SI2) or A61-48 (RFC2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 COOLING FAN ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - BODY GROUND)
a.

Disconnect the No. 2 cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-3 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.INSPECT FAN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT FAN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

16.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (NO. 2 RELAY)

NG

REPLACE FAN NO. 2 RELAY

16.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (NO. 2 RELAY)
A327846C02
0.885,0.427 1.198,0.583 0.313,0.156 10 false *1 2.677,2.052 2.99,2.208 0.313,0.156 10 false *2
*1 No. 2 engine room relay block and junction block assembly
*2 FAN NO. 2 Relay


a.

Remove the FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 2 relay) - Body ground Always 11 to 14 V
1 (FAN NO. 2 relay) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - NO. 2 COOLING FAN ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - NO. 2 COOLING FAN ECU)
a.

Remove the FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the No. 2 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (FAN NO. 2 relay) - A99-1 (+B2) Always Below 1 Ω
5 (FAN NO. 2 relay) or A99-1 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - ECM)
a.

Disconnect the cooling fan ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A93-2 (SI) - A61-49 (RFC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-1 (-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COOLING FAN ECU

NG

20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN ECU - ECM)
a.

Disconnect the No. 2 cooling fan ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (SI2) - A61-48 (RFC2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the No. 2 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-1 (-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 COOLING FAN ECU

NG

REPLACE NO. 2 COOLING FAN MOTOR