Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › COMBINATION SWITCH › from 2015.10
RM3090E _52 Drivetrain _008760 GF1A TRANSFER / 4WD / AWD _0050889 COMBINATION SWITCH G

GF1A TRANSFER / 4WD / AWD  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY (w/o Stop And Start System)

a.
C278686C02
1.417,1.333 1,1.917 1,1.917 0.75,1.917 true 1.917,1.333 2.417,1.917 2.417,1.917 2.667,1.917 true 0.052,0.073 0.365,0.229 0.313,0.156 10 false *a 0.302,1.833 0.917,2.031 0.615,0.198 10 false MSW2 2.719,1.833 3.333,2.031 0.615,0.198 10 false MSW1
*a Component without harness connected (Combination Switch Assembly (Sport Mode Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW1) - 4 (MSW2) Combination switch on (Push) Below 1 Ω
Combination switch off (Release) 10 kΩ or higher


If the result is not as specified, replace the combination switch.


Hide 84970 2.INSPECT COMBINATION SWITCH ASSEMBLY (w/ Stop And Start System)

a.
C278686C03
1.417,1.333 1,1.917 1,1.917 0.75,1.917 true 1.729,1.323 2.229,1.906 2.229,1.906 2.479,1.906 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.552,1.802 3.167,2 0.615,0.198 10 false MSW1 0.521,1.833 0.771,2.083 0.25,0.25 10 false E
*a Component without harness connected (Combination Switch Assembly (Sport Mode Switch))


for Sport Mode Switch:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (MSW1) - 4 (E) Sport mode switch on (Push) Below 1 Ω
Sport mode switch off (Release) 10 kΩ or higher


If the result is not as specified, replace the combination switch.


b.
C278686C04
1.417,1.333 1,1.917 1,1.917 0.75,1.917 true 1.917,1.333 2.417,1.917 2.417,1.917 2.667,1.917 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.531,1.823 0.75,2.031 0.219,0.208 10 false E 2.719,1.833 3.333,2.031 0.615,0.198 10 false ECU
*a Component without harness connected
(Combination Switch Assembly (Stop and Start System Cancel Switch))


for Stop and Start System Cancel Switch:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ECU) - 4 (E) Stop and start system cancel switch on (Push) Below 1 Ω
Stop and start system cancel switch off (Release) 10 kΩ or higher


If the result is not as specified, replace the combination switch.