Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2015.10
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Engine running
Combination switch assembly (ECO mode switch) off
Blower motor on
Temperature set to MAX HOT
IDH terminal signal below 1 V
(Inverter with converter assembly overload not detected)
·

Engine coolant temperature 65°C or less (3 heaters operate)

·

Engine coolant temperature 70°C or less (2 heaters operate)

·

Engine coolant temperature 75°C or less (A heater operates)


Ambient temperature 10°C or less

WIRING DIAGRAM

E269929E03
3.417,1.313 4.583,1.5 1.167,0.188 10 false PTC HTR NO.1 5.917,0.573 6.531,0.771 0.615,0.198 10 false PTC1 1.927,0.708 2.813,0.906 0.885,0.198 10 false ECU-IG NO.3 5.917,1.76 6.531,1.958 0.615,0.198 10 false PTC3 3.469,2.5 4.75,2.781 1.281,0.281 10 false PTC HTR NO.3 5.927,2.948 6.542,3.146 0.615,0.198 10 false PTC2 3.427,3.688 4.5,3.885 1.073,0.198 10 false PTC HTR NO.2 2.073,3.583 2.75,4 0.677,0.417 10 false PTC HTR NO.2 2.073,2.385 2.74,2.75 0.667,0.365 10 false PTC HTR NO.3 2.083,1.198 2.771,1.625 0.688,0.427 10 false PTC HTR NO.1 0.646,1.031 1.5,1.229 0.854,0.198 10 false from Battery 0.125,0.563 1.531,0.771 1.406,0.208 10 false from IG1 NO.2 Relay 5.781,3.354 6.396,3.552 0.615,0.198 10 false G81 5.792,3.542 7.063,3.896 1.271,0.354 10 false Air Conditioning Amplifier Assembly 4.313,4.281 4.458,4.448 0.146,0.167 10 false B 4.323,4.76 4.458,4.927 0.135,0.167 10 false B 4.313,5.302 4.448,5.469 0.135,0.167 10 false B 3.365,5.302 3.5,5.469 0.135,0.167 10 false E 3.365,4.271 3.5,4.438 0.135,0.167 10 false E 3.219,5.521 4.844,5.74 1.625,0.219 10 false Quick Heater Assembly 4.521,4.188 4.802,4.354 0.281,0.167 10 false A31 4.521,4.573 4.802,4.74 0.281,0.167 10 false A31 4.531,5.219 4.813,5.385 0.281,0.167 10 false A31 4.625,3.979 4.75,4.167 0.125,0.188 10 false 1 4.625,4.396 4.75,4.583 0.125,0.188 10 false 2 4.625,5.021 4.75,5.208 0.125,0.188 10 false 3 3.083,3.979 3.208,4.167 0.125,0.188 10 false 1 3.01,4.188 3.292,4.354 0.281,0.167 10 false A30 3.01,5.219 3.292,5.385 0.281,0.167 10 false A35 3.083,5 3.208,5.188 0.125,0.188 10 false 1 3.177,0.458 3.344,0.625 0.167,0.167 10 false 2 3.167,1.667 3.333,1.833 0.167,0.167 10 false 2 3.167,2.833 3.333,3 0.167,0.167 10 false 1 4.5,0.458 4.667,0.625 0.167,0.167 10 false 1 4.5,1.656 4.667,1.823 0.167,0.167 10 false 1 4.5,2.833 4.667,3 0.167,0.167 10 false 2 3.177,0.927 3.344,1.094 0.167,0.167 10 false 5 3.177,2.146 3.344,2.313 0.167,0.167 10 false 5 3.167,3.333 3.333,3.5 0.167,0.167 10 false 5 4.5,0.917 4.667,1.083 0.167,0.167 10 false 3 4.5,2.146 4.667,2.313 0.167,0.167 10 false 3 4.5,3.333 4.667,3.5 0.167,0.167 10 false 3 5.635,0.469 5.844,0.667 0.208,0.198 10 false 40 5.656,1.656 5.865,1.854 0.208,0.198 10 false 39 5.729,2.833 5.854,3.052 0.125,0.219 10 false 3 0.083,0.042 6.51,0.281 6.427,0.24 12 false for Diesel not in Cold Areas (w/o Seat Memory):

E269936E08
0.031,0.031 5.458,0.281 5.427,0.25 12 false for Gasoline, Diesel in Cold Areas (w/o Seat Memory): 5.958,0.594 6.573,0.792 0.615,0.198 10 false PTC1 5.708,0.479 5.896,0.656 0.188,0.177 10 false 40 4.531,1.677 4.719,1.854 0.188,0.177 10 false 2 3.24,0.958 3.427,1.135 0.188,0.177 10 false 5 3.229,0.49 3.417,0.667 0.188,0.177 10 false 2 4.531,0.958 4.719,1.135 0.188,0.177 10 false 3 2.01,0.729 2.854,0.927 0.844,0.198 10 false ECU-IG NO.3 0.219,0.563 1.563,0.76 1.344,0.198 10 false from IG1 NO.2 Relay 0.719,1.021 1.552,1.219 0.833,0.198 10 false from Battery 3.49,1.323 4.646,1.594 1.156,0.271 10 false PTC HTR NO.1 2.115,1.208 2.802,1.604 0.688,0.396 10 false PTC HTR NO.1 5.969,1.771 6.583,1.969 0.615,0.198 10 false PTC2 5.792,1.677 5.917,1.865 0.125,0.188 10 false 3 3.51,2.51 4.698,2.76 1.188,0.25 10 false PTC HTR NO.2 2.125,2.396 2.771,2.917 0.646,0.521 10 false PTC HTR NO.2 3.24,1.667 3.427,1.844 0.188,0.177 10 false 1 3.25,2.146 3.438,2.323 0.188,0.177 10 false 5 4.531,0.49 4.719,0.667 0.188,0.177 10 false 1 4.531,2.156 4.719,2.333 0.188,0.177 10 false 3 4.573,3.135 4.865,3.323 0.292,0.188 10 false A31 4.656,2.927 4.844,3.104 0.188,0.177 10 false 1 4.583,3.74 4.875,3.927 0.292,0.188 10 false A31 4.656,3.531 4.844,3.708 0.188,0.177 10 false 3 3.063,3.135 3.354,3.323 0.292,0.188 10 false A32 3.063,3.75 3.354,3.938 0.292,0.188 10 false A32 3.135,3.542 3.323,3.719 0.188,0.177 10 false 2 3.135,2.938 3.323,3.115 0.188,0.177 10 false 1 3.25,4.094 5,4.344 1.75,0.25 10 false Quick Heater Assembly 5.813,2.208 6.604,2.406 0.792,0.198 10 false G81 5.823,2.406 7.094,2.792 1.271,0.385 10 false Air Conditioning Amplifier Assembly 4.333,3.24 4.521,3.417 0.188,0.177 10 false B 4.354,3.833 4.542,4.01 0.188,0.177 10 false B 3.417,3.833 3.604,4.01 0.188,0.177 10 false E 3.406,3.24 3.594,3.417 0.188,0.177 10 false E

E269936E09
0.031,0.031 5.354,0.271 5.323,0.24 12 false w/ Seat Memory: 5.958,0.594 6.573,0.792 0.615,0.198 10 false PTC1 5.708,0.479 5.896,0.656 0.188,0.177 10 false 40 4.531,1.677 4.719,1.854 0.188,0.177 10 false 1 3.24,0.958 3.427,1.135 0.188,0.177 10 false 5 3.229,0.49 3.417,0.667 0.188,0.177 10 false 2 4.531,0.958 4.719,1.135 0.188,0.177 10 false 3 2.01,0.729 2.854,0.927 0.844,0.198 10 false ECU-IG NO.3 0.219,0.563 1.563,0.76 1.344,0.198 10 false from IG1 NO.2 Relay 0.719,1.021 1.552,1.219 0.833,0.198 10 false from Battery 3.49,1.323 4.646,1.594 1.156,0.271 10 false PTC HTR NO.1 2.104,1.208 2.792,1.688 0.688,0.479 10 false PTC HTR NO.1 5.969,1.771 6.583,1.969 0.615,0.198 10 false PTC2 5.792,1.677 5.917,1.865 0.125,0.188 10 false 3 3.51,2.51 4.698,2.76 1.188,0.25 10 false PTC HTR NO.2 2.115,2.385 2.771,2.906 0.656,0.521 10 false PTC HTR NO.2 3.24,1.667 3.427,1.844 0.188,0.177 10 false 2 3.25,2.146 3.438,2.323 0.188,0.177 10 false 5 4.531,0.49 4.719,0.667 0.188,0.177 10 false 1 4.531,2.156 4.719,2.333 0.188,0.177 10 false 3 4.573,3.135 4.865,3.323 0.292,0.188 10 false A31 4.656,2.927 4.844,3.104 0.188,0.177 10 false 1 4.583,3.74 4.875,3.927 0.292,0.188 10 false A31 4.656,3.531 4.844,3.708 0.188,0.177 10 false 3 3.063,3.135 3.354,3.323 0.292,0.188 10 false A32 3.063,3.75 3.354,3.938 0.292,0.188 10 false A32 3.135,3.542 3.323,3.719 0.188,0.177 10 false 2 3.135,2.938 3.323,3.115 0.188,0.177 10 false 1 3.26,4.094 4.927,4.333 1.667,0.24 10 false Quick Heater Assembly 5.813,2.208 6.604,2.406 0.792,0.198 10 false G81 5.823,2.406 7.094,2.792 1.271,0.385 10 false Air Conditioning Amplifier Assembly 4.333,3.24 4.521,3.417 0.188,0.177 10 false B 4.354,3.833 4.542,4.01 0.188,0.177 10 false B 3.417,3.833 3.604,4.01 0.188,0.177 10 false E 3.406,3.24 3.594,3.417 0.188,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Heater Active Level Quick heater assembly Min.: 0, Max.: 3 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33
OK:

Heater Active Level does not change normally.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PTC HEATER RELAY
2.INSPECT PTC HEATER RELAY
a.

for Diesel not in Cold Areas (w/o Seat Memory):

E269960C01
1.125,0.927 0.948,0.719 0.948,0.719 0.813,0.719 true 1.542,0.927 1.719,0.74 1.719,0.74 1.865,0.74 true 1.354,0.75 1.531,0.563 1.531,0.563 1.677,0.563 true 1.344,1.229 1.521,1.479 1.521,1.479 1.667,1.479 true 0.646,0.635 0.802,0.833 0.156,0.198 10 1 1.917,0.667 2.073,0.865 0.156,0.198 10 2 1.729,0.479 1.885,0.677 0.156,0.198 10 5 1.729,1.396 1.885,1.594 0.156,0.198 10 3 4.073,1.052 4.229,1.25 0.156,0.198 10 1 3,1.042 3.156,1.25 0.156,0.208 10 2 3,0.646 3.156,0.844 0.156,0.198 10 3 4.073,0.646 4.229,0.844 0.156,0.198 10 5 5.094,1.052 5.25,1.25 0.156,0.198 10 1 6.177,1.052 6.333,1.25 0.156,0.198 10 2 6.177,0.646 6.333,0.844 0.156,0.198 10 5 5.104,0.646 5.26,0.844 0.156,0.198 10 3 2.677,0.063 2.969,0.26 0.292,0.198 10 *1 4.792,0.052 5.083,0.25 0.292,0.198 10 *2
*1 PTC HTR NO.2 Relay *2 PTC HTR NO.1 Relay, PTC HTR NO.3 Relay


i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω




b.

for Gasoline, Diesel in Cold Areas (w/o Seat Memory):

E269961C01
1.438,1.24 1.125,1.385 1.125,1.385 0.948,1.385 true 1.271,0.75 1.115,0.49 1.115,0.49 0.938,0.49 true 1.583,0.729 1.792,0.542 1.792,0.542 1.958,0.542 true 1.469,0.958 1.771,1.073 1.771,1.073 1.938,1.073 true 0.823,0.417 0.979,0.615 0.156,0.198 10 1 2,0.469 2.156,0.667 0.156,0.198 10 2 1.99,0.99 2.146,1.188 0.156,0.198 10 5 0.833,1.302 0.99,1.5 0.156,0.198 10 3 3,0.656 3.156,0.854 0.156,0.198 10 3 4.073,0.656 4.229,0.854 0.156,0.198 10 5 5.094,0.656 5.25,0.854 0.156,0.198 10 3 6.177,0.656 6.333,0.854 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 2 4.073,1.052 4.229,1.25 0.156,0.198 10 1 5.094,1.052 5.25,1.25 0.156,0.198 10 1 6.177,1.052 6.333,1.25 0.156,0.198 10 2 2.74,0.094 2.948,0.302 0.208,0.208 10 *1 4.844,0.073 5.052,0.281 0.208,0.208 10 *2
*1 PTC HTR NO.2 Relay *2 PTC HTR NO.1 Relay


i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω




c.
E222294C16
1.115,0.938 1.219,0.479 1.219,0.479 1.354,0.479 false 1.063,1.344 1.229,1.75 1.229,1.75 1.365,1.75 false 0.563,1.281 0.729,1.75 0.729,1.75 0.885,1.75 false 0.792,0.979 0.688,0.5 0.688,0.5 0.531,0.5 false 1.385,0.396 1.604,0.656 0.219,0.26 10 false 1 1.385,1.667 1.604,1.927 0.219,0.26 10 false 2 0.906,1.667 1.125,1.927 0.219,0.26 10 false 3 0.448,0.406 0.667,0.667 0.219,0.26 10 false 5 1.885,0.219 2.198,0.417 0.313,0.198 10 false *1
*1 PTC HTR NO.2 Relay
PTC HTR NO.1 Relay


w/ Seat Memory:

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)

NG

REPLACE PTC HEATER RELAY

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)
a.

for Diesel not in Cold Areas (w/o Seat Memory):

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.2:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.3:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




b.

for Gasoline, Diesel in Cold Areas (w/o Seat Memory):

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.2:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




c.

w/ Seat Memory:

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.2:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

for Diesel not in Cold Areas (w/o Seat Memory):

i.

Disconnect the G81 air conditioning amplifier assembly connector.


ii.

Remove the PTC heater relays from the No. 2 engine room relay block.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - G81-40 (PTC1) Always Below 1 Ω
2 - G81-3 (PTC2) Always Below 1 Ω
1 - G81-39 (PTC3) Always Below 1 Ω
G81-40 (PTC1) - Body ground Always 10 kΩ or higher
G81-3 (PTC2) - Body ground Always 10 kΩ or higher
G81-39 (PTC3) - Body ground Always 10 kΩ or higher




b.

for Gasoline, Diesel in Cold Areas (w/o Seat Memory):

i.

Disconnect the G81 air conditioning amplifier assembly connector.


ii.

Remove the PTC heater relays from the No. 2 engine room relay block.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - G81-40 (PTC1) Always Below 1 Ω
2 - G81-3 (PTC2) Always Below 1 Ω
G81-40 (PTC1) - Body ground Always 10 kΩ or higher
G81-3 (PTC2) - Body ground Always 10 kΩ or higher




c.

w/ Seat Memory:

i.

Disconnect the G81 air conditioning amplifier assembly connector.


ii.

Remove the PTC heater relays from the No. 2 engine room relay block.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - G81-40 (PTC1) Always Below 1 Ω
1 - G81-3 (PTC2) Always Below 1 Ω
G81-40 (PTC1) - Body ground Always 10 kΩ or higher
G81-3 (PTC2) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)
a.

for Diesel not in Cold Areas (w/o Seat Memory):

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Disconnect the A31 quick heater assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
3 - A31-1 (B) Always Below 1 Ω
A31-1 (B) - Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
3 - A31-2 (B) Always Below 1 Ω
A31-2 (B) - Body ground Always 10 kΩ or higher

PTC HTR NO.3:
Tester Connection Condition Specified Condition
3 - A31-3 (B) Always Below 1 Ω
A31-3 (B) - Body ground Always 10 kΩ or higher




b.

for Gasoline, Diesel in Cold Areas (w/o Seat Memory):

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Disconnect the A31 quick heater assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
3 - A31-1 (B) Always Below 1 Ω
A31-1 (B) - Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
3 - A31-3 (B) Always Below 1 Ω
A31-3 (B) - Body ground Always 10 kΩ or higher




c.

w/ Seat Memory:

i.

Remove the PTC heater relays from the No. 2 engine room relay block.


ii.

Disconnect the A31 quick heater assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
3 - A31-1 (B) Always Below 1 Ω
A31-1 (B) - Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
3 - A31-3 (B) Always Below 1 Ω
A31-3 (B) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)
a.

for Diesel not in Cold Areas (w/o Seat Memory):

i.

Disconnect the A30 and A35 quick heater assembly connectors.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (E) - Body ground Always Below 1 Ω
A35-1 (E) - Body ground Always Below 1 Ω




b.

for Gasoline, Diesel in Cold Areas (w/o Seat Memory):

i.

Disconnect the A32 quick heater assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-1 (E) - Body ground Always Below 1 Ω
A32-2 (E) - Body ground Always Below 1 Ω




c.

w/ Seat Memory:

i.

Disconnect the A32 quick heater assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-1 (E) - Body ground Always Below 1 Ω
A32-2 (E) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

7.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT QUICK HEATER ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG