Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2015.10
RM3090E _53 Suspension _008766 TIRE / WHEEL _0050243 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure (for Korea):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)
225/65R17 102H 230 (2.3, 33) 230 (2.3, 33)


Cold Tire Inflation Pressure (for General Export):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
225/65R17 102H 220 (2.2, 32) 220 (2.2, 32)
235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)


Cold Tire Inflation Pressure (for Europe):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
225/65R17 102H 240 (2.4, 35) 240 (2.4, 35)
220 (2.2, 32)* 220 (2.2, 32)*
235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)
225/60R18 100H 210 (2.1, 30) 210 (2.1, 30)


*: for Ireland, Hungary, Romania and Turkey

Cold Tire Inflation Pressure (for Compact Spare Tire):
Tire Size kPa (kgf/cm2, psi)
T165/80D17 104M 420 (4.2, 60)



b.
C137874

Using a dial indicator, check the runout of the tires.

Tire runout:

1.4 mm (0.0551 in.) or less


HINT:

Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.



Hide 2. ROTATE TIRES

a.
C241094C01
0.401,2.276 0.578,2.429 0.177,0.153 10 *a 0.401,0.557 0.578,0.71 0.177,0.153 10 *a 1.798,0.158 1.975,0.31 0.177,0.153 10 *b 1.798,1.911 1.975,2.064 0.177,0.153 10 *c
*a Front of the Vehicle
*b Vehicle Wheels and Spare Tire Wheel are Same Type
*c Vehicle Wheels and Spare Tire Wheel are Not Same Type, or There is No Spare Tire


Rotate the tires as shown in the illustration.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


Hide 3.INSPECT WHEEL BALANCE

a.
C264658N01
2.098,3.633 2.240,3.803 0.142,0.170 10 A

for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Maximum imbalance after adjustment:

8.0 g (0.0176 lb.)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the sticking surface of the tape.

·

Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight firmly to adhere it to the position.

·

Do not reuse the balance weight.



HINT:
·

The inner side balance weights should be installed by clipping them to the rim.

·

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.




b.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Maximum imbalance after adjustment:

8.0 g (0.0176 lb.)


HINT:

If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.



Hide 4.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 6.INSPECT REAR AXLE HUB BEARING LOOSENESS