RM3090E
_V1
General
_009232
SPECIFICATIONS
_0208133
2WW ENGINE MECHANICAL
F
SPECIFICATIONS 2WW ENGINE MECHANICAL SERVICE DATA
ENGINE
| Engine idle speed
|
830 rpm
|
| Maximum engine speed
|
3800 rpm
|
| Compression
|
Standard pressure
|
1600 kPa (16.3 kgf/cm2, 232 psi) or higher
|
| Difference between each cylinder
|
All cylinders almost same valve
|
CYLINDER HEAD GASKET
| Cylinder head gasket
|
Standard piston protrusion
|
0.420 to 0.680 mm (0.0165 to 0.0268 in.)
|
| Piston protrusion
|
0.92 mm (0.00362 in.)
|
Use 1 hole
|
| 0.92 to 1.03 mm (0.0362 to 0.0406 in.)
|
Use 2 hole
|
| 1.03 to 1.18 mm (0.0406 to 0.0465 in.)
|
Use 3 hole
|
ENGINE UNIT
| Camshaft
|
Runout
|
0.03 mm (0.00118 in.)
|
| No. 2 camshaft
|
Runout
|
0.03 mm (0.00118 in.)
|
CYLINDER HEAD
| Intake valve
|
Valve stem diameter
|
Standard
|
4.92 mm (0.194 in.)
|
| Exhaust valve
|
Valve stem diameter
|
Standard
|
4.92 mm (0.194 in.)
|
| Intake valve seat
|
Width
|
Standard
|
1.2 mm (0.0472 in.)
|
| Exhaust valve seat
|
Width
|
Standard
|
1.4 mm (0.0551 in.)
|
| Camshaft
|
Thrust clearance
|
Standard
|
0.033 to 0.150mm (0.00130 to 0.00591 in.)
|
CYLINDER BLOCK
| Connecting rod
|
Oil clearance
|
Standard
|
0.015 to 0.050 mm (0.000591 to 0.00197 in.)
|
| Crankshaft
|
Thrust clearance
|
Standard
|
0.06 to 0.25 mm (0.00236 to 0.00984 in.)
|
| Cylinder bore
|
Reference value (New parts)
|
STD
|
84.000 to 84.002 mm (3.30708 to 3.30716 in.)
|
| O/S 0.25
|
84.250 to 84.252 mm (3.31692 to 3.31700 in.)
|
| Piston
|
Piston diameter
|
STD
|
83.950 to 83.970 mm (3.30708 to 3.30716 in.)
|
| O/S 0.25
|
84.200 to 84.220 mm (3.3149 to 3.31574 in.)
|
| Oil clearance
|
New piston
|
0.03 to 0.17 mm (0.00118 to 0.00669 in.)
|
| Maximum
|
More than 0.25 mm (0.00984 in.)
|
| Piston ring
|
Ring groove clearance
|
No. 1 compression spring
|
Standard
|
0.07 to 0.11 mm (0.00275 to 0.00435 in.)
|
| No. 2 compression spring
|
| End gap
|
No. 1 compression spring
|
Standard
|
0.15 to 0.25 mm (0.00590 to 0.0984 in.)
|
| No. 2 compression spring
|
0.30 to 0.45 mm (0.0118 to 0.0177 in.)
|
| Crankshaft
|
Oil clearance
|
Standard
|
0.023 to 0.054 mm (0.000906 to 0.00213 in.)
|
| Crankshaft main journal
|
Diameter
|
Mark 1
|
Standard
|
54.984 to 54.990 mm (2.16472 to 2.16496 in.)
|
| Mark 2
|
Standard
|
54.977 to 54.983 mm (2.16444 to 2.16469 in.)
|
| Mark 3
|
Standard
|
54.971 to 54.976 mm (2.16421 to 2.16441 in.)
|
| U/S 0.25
|
Mark 1
|
Standard
|
54.734 to 54.740 mm (2.15488 to 2.15511 in.)
|
| Mark 2
|
Standard
|
54.727 to 54.733 mm (2.15460 to 2.15484 in.)
|
| Mark 3
|
Standard
|
54.721 to 54.726 mm (2.15437 to 2.15457 in.)
|