These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly) and the ECM, main body ECU (multiplex network body ECU) or combination meter assembly.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | CAN communication error between the certification ECU (smart key ECU assembly) and ECM (1-trip detection*) | ECM | Turn the engine switch on (IG) and wait 10 seconds or more. |
| U0140 | Lost Communication with Main Body ECU | CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip detection*) | Main body ECU (multiplex network body ECU) | Always |
| U0142 | Lost Communication with Main Body ECU | CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip detection*) | Main body ECU (multiplex network body ECU) | Always |
| U0155 | Lost Communication with Combination Meter | CAN communication error between the certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection*) | Combination meter assembly | Turn the engine switch on (IG) and wait 10 seconds or more. |
| U1103 | Lost Communication with Stop and Start Control Module | CAN communication malfunction between the certification ECU (smart key ECU assembly) and engine stop and start ECU (1-trip detection logic*). | Engine stop and start ECU | Turn the engine switch on (IG) and wait 10 seconds or more. |
*: Only detected while a malfunction is present and the engine switch is on (IG)
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
| U0100 | There is no effect on vehicle behavior. | If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.
·
When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking. ·
When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking. If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE). ·
When the engine switch is pressed, the engine stops cranking after 6 seconds. ·
When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds. |
| U0140
U0142 |
Doors cannot be locked or unlocked. The warning (wireless buzzer) does not sound. | - |
| U0155 | The warning (meter buzzer) does not sound and the meter does not indicate a warning. - | - |
| U1103 | ·
The engine stall misjudgment is done by the idling stop by stop and start system. ·
Immobiliser set is done by the door operation in the idling stop by stop and start system |
- |
Related Data List and Active Test Items
| DTC | Data List Item | Active Test Item |
|---|---|---|
| U0100
U0140 U0142 U0155 U1103 |
- | - |
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
Note any DTCs that are output.
| Proceed to |
|---|
| NEXT (for LHD) |
| NEXT (for RHD) |
NEXT (for LHD)
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
NEXT (for RHD)
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING