Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0049569 FRONT SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 89543 1.INSTALL FRONT SPEED SENSOR LH

NOTICE:

To prevent interference with other parts, do not twist the painted line areas of the sensor wire when installing it.


a.

Set the sensor into the knuckle, and then install the sensor with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Keep the sensor tip and sensor installation hole free from foreign matter.

·

Firmly insert the sensor body into the knuckle before tightening the bolt.

·

After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also, make sure that no foreign matter is stuck between the parts.

·

To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.




b.
C279262C01
1.813,0.917 1.063,0.552 1.063,0.552 0.833,0.552 false 2.24,0.958 2.417,0.177 2.417,0.177 2.542,0.177 false 1.76,2.177 2,2.885 2,2.885 2.167,2.885 false 2.583,0.104 2.75,0.292 0.167,0.188 10 *1 0.615,0.469 0.781,0.646 0.167,0.177 10 *2 2.219,2.813 2.375,2.979 0.156,0.167 10 *a 3,0.583 3.156,0.781 0.156,0.198 10 A 2.688,1.813 2.844,2.01 0.156,0.198 10 B 2.021,0.438 2.177,0.635 0.156,0.198 10 C 1.833,1.313 1.99,1.51 0.156,0.198 10 D 2.302,2.177 2.458,2.375 0.156,0.198 10 F 3.198,1.656 3.354,1.854 0.156,0.198 10 E
*1 Flexible Hose Clamp
*2 Flexible Hose Bracket
*a Painted Line


Install the sensor clamp and sensor clip as follows.

i.

Simultaneously perform the following: 1) hang the hook part of the sensor clamp labeled A on the part of the flexible hose bracket labeled C; and 2) insert the hook part of the sensor clamp labeled B to the part of the flexible hose bracket labeled D.

NOTICE:

Do not twist the sensor wire when installing the clamp.



ii.

Install the sensor clamp to the flexible hose clamp and flexible hose bracket with the bolt labeled E.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


iii.

Insert the sensor clip labeled F into the hole on the absorber lower bracket.



c.

Install the sensor clamp and sensor clip as follows.

i.

Set the sensor clamp on the side member, and then install the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamp.



ii.

Insert the sensor clip into the hole on the apron.



d.

Connect the sensor connector.


Hide 53876A 2.INSTALL FRONT FENDER LINER LH

HINT:

Install the fender liner so that the sensor wire harness passes beyond the fender liner installation clip towards the rear side of the vehicle.


Hide 3.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)