Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start, Main Body, Power Source Control, Back Door* or Combination Meter / Data List.

*: w/ Power Back Door System



e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Touch Sensor Driver door touch sensor (unlock sensor)*1 ON or OFF ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


P-Door Touch Sensor Front passenger door touch sensor (unlock sensor)*1 ON or OFF ON: Front passenger door touch sensor (unlock sensor) touched
OFF: Front passenger door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


D-Door Trigger Switch Driver door touch sensor (lock sensor)*1 ON or OFF ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


P-Door Trigger Switch Front passenger door touch sensor (lock sensor)*1 ON or OFF ON: Front passenger door touch sensor (lock sensor) touched
OFF: Front passenger door touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Tr/B-Door Lock SW Back door opener switch assembly (lock switch) ON or OFF ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.


Tr/B-Door Unlock SW Back door opener switch (unlock switch) ON or OFF ON: Back door opener switch (unlock switch) pushed
OFF: Back door opener switch (unlock switch) not pushed
·

Displays whether the back door opener switch (unlock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.


Ignition Switch Engine switch on (IG) ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
·

Displays whether the IG power source signal input is on or off.

·

Use this Data List item to help determine the cause when all entry and system/wireless functions do not operate.

·

If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal*4 or clutch pedal*5, the engine switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the L code stored in the certification ECU (smart key ECU assembly) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered on (IG) at that time*2.

·

If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal, the engine switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the S code stored in the certification ECU (smart key ECU assembly) and the code stored in the ID code box (immobiliser code ECU) are compared, and if all codes match, the power source mode is considered on (IG) at that time*3.


Unmatched Vehicle-ID Key No. (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

A communication error due to electric wave interference.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


No Response Communication response Yes or No Yes: Communication malfunction
No: Communication normal
The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Unmatch Code or Form Code format (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes:
·

An electrical key transmitter sub-assembly from a different manufacturer is being used.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Key Low Battery Transmitter battery depleted Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C [-4°F], "Yes" may be displayed even if the transmitter battery is new).
Power Save Cnt 10 Min. Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more 0 to 255 Within range of 0 to 255 If the electrical key transmitter sub-assembly is in a vehicle exterior detection area, communication is frequently performed between the vehicle and electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the transmitter battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the entry and start system automatically deactivates the exterior detection area the electrical key transmitter is in. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.
Power Save Cnt 5 Days Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to engine not being started for 5 days or more 0 to 255 Within range of 0 to 255 -
Power Save Cnt 14 Days Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger door disabled) is activated due to engine not being started for 14 days or more 0 to 255 Within range of 0 to 255 -
# Codes Number of trouble codes Min: 0, Max: 255 Number of stored DTCs displayed -
ID Code Difference(Resp) ID code (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


C Code Difference Challenge code (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes:
·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


ID Code Difference Wireless ID code (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference(Resp)" in the Data List.)
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

A communication error due to external noise (RF).

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Immobilizer when IG=ON Immobiliser system status when power source mode on (IG) SET or UNSET SET: Immobiliser system set (engine switch off)
UNSET: Immobiliser system unset (engine switch on [ACC] or on [IG])
-
Immobiliser Immobiliser system status determined by certification ECU Set or Unset Set: Immobiliser set (engine start prohibited) (engine switch off)
Unset: Immobiliser unset (engine start permitted) (engine switch on [ACC] or on [IG])
When the immobiliser system does not change to the unset state, this item can be used to determine if the cause is the certification ECU or ID code box.
Different Rolling Code Rolling code (incorrect or correct) Yes or No Yes: Communication malfunction
No: Communication normal
The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different.
Other potential causes:
·

An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle.

·

A communication error due to external noise (RF).

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Auto Entry Cancel SW Entry cancel function setting OFF or ON Mode status displayed
ON: Entry and start system canceled
OFF: Entry and start system not canceled
The default setting for the entry cancel function is OFF. If the customer requests that the entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function.
S Code Check S code verification result*3 OK or NG OK: S code verification result normal
NG: S code verification result abnormal
Problems may be caused by the following:
·

Registration has not been performed for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

Malfunctions in the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).


L Code Check L code verification result OK or NG OK: L code verification result normal
NG: L code verification result abnormal
Problems may be caused by the following:
·

Registration has not been performed for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).

·

Malfunctions in the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).


Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on [ACC] or on [IG], or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on [ACC] or on [IG], and engine start operation not performed)
-
Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P*4 and engine switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P*4 and engine switch off)
-
S Code Check(Past) S code verification result (past)*3 OK or NG (Past) OK: Verification result normal
NG (Past): Verification result abnormal (past)
-
L Code Check(Past) L code verification result (past) OK or NG (Past) OK: Verification confirmed (past)
NG (Past): Verification not confirmed (past)
-
Steering Lock State of whether steering lock ECU (steering lock actuator assembly) has determined steering is locked Set or Unset Set: Steering locked
Unset: Steering unlocked
-
Steering Unlock State of whether steering lock ECU (steering lock actuator assembly) determined steering is unlocked Set or Unset Set: Steering unlocked
Unset: Steering locked
-
Ignition Available Area Ignition available area Front or All Customization status displayed -
Parking Wait Time Parking wait time 0.5s, 1.5s, 2.5s or 5s Customization status displayed -
B-Dr Opening Operation Back door opening operation Long, Twice, OFF Customization status displayed -
Touch Activation Over Threshold Consecutive entry lock operation Active or Not Active Customization status displayed -
Wireless Signal Encryption Support Wireless Signal Encryption Support Yes or No Customization status displayed -
Key Low Battery Warning Low transmitter battery warning ON or OFF Customization status displayed -
Key Left in Vehicle Buz Key left in vehicle buzzer sounds ON or OFF Customization status displayed -
Engine Start Indicator Engine start indicator lights ON or OFF Customization status displayed -
Short in Fr P Side Door Oscillators Circuit (Hist) Short in front passenger side door electrical key antenna circuit (history) OK or NG (Hist) OK: Front passenger side door electrical key antenna circuit was normal
NG (Hist): Front passenger side door electrical key antenna circuit was abnormal
-
Short in D Side Door Oscillators Circuit (Hist) Short in driver side door electrical key antenna circuit (history) OK or NG (Hist) OK: Driver side door electrical key antenna circuit was normal
NG (Hist): Driver side door electrical key antenna circuit was abnormal
-
Short in Front P Side Door Oscillators Circuit Short in front passenger side door electrical key antenna circuit OK or NG OK: Front passenger side door electrical key antenna circuit is normal
NG: Front passenger side door electrical key antenna circuit is abnormal
-
Short in Driver Side Door Oscillators Circuit Short in driver side door electrical key antenna circuit OK or NG OK: Driver side door electrical key antenna circuit is normal
NG: Driver side door electrical key antenna circuit is abnormal
-
·

*1: Data from an actual vehicle provided for reference.

·

*2: w/ ID Code Box (Immobiliser Code ECU)

·

*3: w/o ID Code Box (Immobiliser Code ECU)

·

*4: except Manual Transaxle

·

*5: for Manual Transaxle


B251338E08
0.668,0.68 1.644,0.852 0.975,0.172 10 Unlock Sensor 0.668,1.894 1.514,2.066 0.845,0.172 10 Lock Sensor 2.159,0.68 2.495,0.857 0.337,0.177 10 ON 2.159,0.986 2.495,1.163 0.337,0.177 10 OFF 2.159,1.894 2.495,2.071 0.337,0.177 10 ON 2.159,2.16 2.495,2.337 0.337,0.177 10 OFF 3.328,0.11 3.503,0.282 0.175,0.173 10 *1 3.547,0.227 3.722,0.399 0.175,0.173 10 *2 5.422,0.227 5.597,0.399 0.175,0.173 10 *2 5.186,0.11 5.361,0.282 0.175,0.173 10 *3

HINT:
·

*1: With engine switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors locked, front door outside handle assembly (unlock sensor) touched.

·

*2: Approximately 150 ms

·

*3: With engine switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors unlocked, front door outside handle assembly (lock sensor) touched.



Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch status ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
"OFF" is also displayed for this item when the engine switch is on (ACC)
IG SW Engine switch status ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"ON" is also displayed for this item when the engine switch is on (IG)
RR Door Courtesy SW Rear RH door courtesy light switch ON or OFF ON: Rear RH door open
OFF: Rear RH door closed
-
RL Door Courtesy SW Rear LH door courtesy light switch ON or OFF ON: Rear LH door open
OFF: Rear LH door closed
-
Back Door Courtesy SW Back door courtesy light switch ON or OFF ON: Back door open
OFF: Back door closed
-
FR Door Lock Pos Front RH door unlock detection switch signal UNLOCK or LOCK UNLOCK: Front RH door unlocked
LOCK: Front RH door locked
-
FR Door Courtesy SW Front RH door courtesy light switch signal ON or OFF ON: Front RH door open
OFF: Front RH door closed
-
FL Door Lock Pos Front LH door unlock detection switch signal UNLOCK or LOCK UNLOCK: Front LH door unlocked
LOCK: Front LH door locked
-
FL Door Courtesy SW Front LH door courtesy light switch signal ON or OFF ON: Front LH door open
OFF: Front LH door closed
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
Hazard Answer Back Hazard answer-back of entry function ON or OFF Customization status displayed -
Open Door Warning Open door warning ON or OFF Customization status displayed -
Auto Lock Time Automatic lock time 120 s, 60 s or 30 s Customization status displayed -
Wireless Buzzer Vol Entry door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 Customization status displayed -
Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P* ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P* and the engine switch is off, if any door is opened then closed, the steering is locked.

·

When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON ALL OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) (ACC relay on)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

*: except Manual Transaxle


Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0, Max.: 255 Almost the same as actual vehicle speed -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start or Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Overhead Tuner Power Supply ON Door control receiver OFF/ON -
Power for P-Seat Sens Front door outside handle (for front passenger door) OFF/ON -
Multi Channel SW Door control receiver CH1/CH2 -
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Door Lock Door lock motor Unlock/Lock/OFF -
Trunk and Back-Door Open Operate back door lock motor OFF/ON -
Wireless Buzzer Wireless door lock buzzer OFF/ON -