Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly [front floor], [rear floor] or [inside luggage]) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the engine switch cannot be turned on (IG) and the engine cannot be started.

When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B300397E10
5.385,0.594 5.958,0.938 0.573,0.344 10 CG5B 1.948,0.615 2.5,0.792 0.552,0.177 10 CLGB 2.521,0.479 2.75,0.698 0.229,0.219 10 3 1.917,0.979 2.542,1.26 0.625,0.281 10 ANTE5 0.875,1.25 1.333,1.427 0.458,0.177 10 G45 0.875,1.417 3.427,1.875 2.552,0.458 10 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 2.521,0.854 2.656,1.021 0.135,0.167 10 1 5.135,0.396 5.323,0.563 0.188,0.167 10 2 5.396,0.969 5.969,1.188 0.573,0.219 10 CLG5 5.135,0.781 5.323,0.948 0.188,0.167 10 3 5.396,2.365 5.875,2.594 0.479,0.229 10 CG6B 1.948,2.375 2.677,2.719 0.729,0.344 10 CLGB 2.521,2.281 2.729,2.479 0.208,0.198 10 3 1.938,2.76 2.563,3.042 0.625,0.281 10 ANTE6 0.885,3.031 1.229,3.198 0.344,0.167 10 M18 0.875,3.188 3.479,3.625 2.604,0.438 10 No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 2.521,2.656 2.698,2.875 0.177,0.219 10 1 5.063,2.167 5.271,2.333 0.208,0.167 10 10 5.396,2.74 5.917,3.042 0.521,0.302 10 CLG6 5.073,2.542 5.281,2.708 0.208,0.167 10 11 4.76,4.979 6.865,5.51 2.104,0.531 10 Certification ECU (Smart Key ECU Assembly) 5.021,2.729 5.531,2.917 0.51,0.188 10 G83 5.021,2.365 5.427,2.583 0.406,0.219 10 G83 5.021,0.979 5.417,1.281 0.396,0.302 10 G84 5.021,0.604 5.417,0.833 0.396,0.229 10 G84 5.396,4.063 6.042,4.229 0.646,0.167 10 CG7B 5.135,3.865 5.344,4.031 0.208,0.167 10 8 5.396,4.448 6,4.635 0.604,0.188 10 CLG7 5.135,4.25 5.344,4.417 0.208,0.167 10 9 5.021,4.427 5.573,4.594 0.552,0.167 10 G83 5.021,4.063 5.49,4.26 0.469,0.198 10 G83 1.948,4.104 2.406,4.406 0.458,0.302 10 CLGB 2.521,3.969 2.708,4.177 0.188,0.208 10 3 1.948,4.438 2.521,4.729 0.573,0.292 10 ANTE7 2.5,4.333 2.677,4.51 0.177,0.177 10 1 0.896,4.708 1.281,4.875 0.385,0.167 10 M21 0.896,4.865 3.792,5.292 2.896,0.427 10 No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.

·

The door control receiver is also related to interior verification.



PROCEDURE

1.CHECK ENTRY DOOR LOCK OPERATION
a.

Check that the entry lock and unlock functions operate for each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry functions do not operate.


OK:

All door entry lock and unlock functions operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK PUSH START FUNCTION

NG

2.CHECK PUSH START FUNCTION
a.
B323969C01
2.25,0.635 2.635,0.333 false 0.708,0.406 1.104,0.604 false 2.667,0.24 2.979,0.438 0.313,0.198 10 *2 0.531,0.333 0.844,0.531 0.313,0.198 10 *1
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


Remove the transmitter battery of the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT


b.

With the brake pedal*1 or clutch pedal*2 depressed, face the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch and then press the engine switch.

·

*1: except Manual Transaxle

·

*2: for Manual Transaxle



c.

When operating the engine switch, check whether the engine starts.

HINT:
·

When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the engine switch.

·

If the engine cannot be started when performing this inspection, the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU)* may be malfunctioning.

*: w/ ID Code Box (Immobiliser Code ECU)



OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform a entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Check that the customize status of the "Ignition Available Area" has been "All".


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (rear floor).



d.

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage) and perform a entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Check that the customize status of the "Ignition Available Area" has been "All".


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key antenna assembly (inside luggage).



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, the vehicle may be have the effects of wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



Result:
Proceed to
Entry and start system cannot be operated
Entry and start system can be operated



Entry and start system cannot be operated

4.CHECK KEY DIAGNOSTIC MODE

Entry and start system can be operated

AFFECTED BY WAVE INTERFERENCE

4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B340886C01
0.625,1.156 2.396,0.24 2.396,0.24 2.563,0.24 false 1.75,1.146 2.406,0.24 false 2.594,0.156 2.906,0.354 0.313,0.198 10 *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B340887C01
0.688,1.052 2.385,0.208 2.385,0.208 2.573,0.208 false 1.688,1.052 2.385,0.208 false 2.615,0.115 2.927,0.313 0.313,0.198 10 *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B340884C01
1.115,1.729 0.75,1.49 0.75,1.49 1.51,1.042 false 0.583,1.396 0.896,1.594 0.313,0.198 10 *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna (inside luggage):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:
·

If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

·

It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage) is operating by the sounding of the buzzer.

·

If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may be malfunctioning.



OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
Front floor operation check fails
Rear floor operation check fails
Inside luggage operation check fails
All operation checks are normal



Front floor operation check fails

5.CHECK HARNESS AND CONNECTOR (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)

Rear floor operation check fails

9.CHECK HARNESS AND CONNECTOR (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)

Inside luggage operation check fails

13.CHECK HARNESS AND CONNECTOR (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)

All operation checks are normal

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-1 (ANTE5) - G84-3 (CLG5) Always Below 1 Ω
G45-3 (CLGB) - G84-2 (CG5B) Always Below 1 Ω
G45-1 (ANTE5) or G84-3 (CLG5) - Body ground Always 10 kΩ or higher
G45-3 (CLGB) or G84-2 (CG5B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA)
a.
B250988C16
0.844,0.51 1.219,0.781 0.375,0.271 1.135,1.219 1.323,1.219 1.323,1.219 1.5,0.885 false 2.333,1.208 2.146,1.208 2.146,1.208 1.906,0.875 false 0.063,0.073 0.323,0.323 0.26,0.25 10 *a 0.771,3.156 1.156,3.354 0.385,0.198 10 *c 1.719,3.167 2.083,3.396 0.365,0.229 10 *d 0.073,1.406 0.354,1.677 0.281,0.271 10 *b 0.083,2.292 0.521,2.5 0.438,0.208 10 GND 0.563,1.135 1.167,1.375 0.604,0.24 10 ANTE5 2.375,1.125 2.917,1.302 0.542,0.177 10 CLGB 0.917,0.563 1.281,0.76 0.365,0.198 10 G45
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna [Front Floor])
*b Waveform
*c Within approximately 30 seconds from when the door is closed
*d After approximately 30 seconds from when the door is closed


Disconnect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.


b.

Connect the G84 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
G45-1 (ANTE5) - G45-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

7.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Instrument Panel Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK KEY DIAGNOSTIC MODE
8.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.
B340886C01
0.625,1.156 2.396,0.24 2.396,0.24 2.563,0.24 false 1.75,1.146 2.406,0.24 false 2.594,0.156 2.906,0.354 0.313,0.198 10 *a
*a Inspection Point


Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the No. 1 indoor electrical key antenna assembly (front floor). When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the M18 No. 2 indoor electrical key antenna assembly (rear floor) connector.


b.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M18-1 (ANTE6) - G83-11 (CLG6) Always Below 1 Ω
M18-3 (CLGB) - G83-10 (CG6B) Always Below 1 Ω
M18-1 (ANTE6) or G83-11 (CLG6) - Body ground Always 10 kΩ or higher
M18-3 (CLGB) or G83-10 (CG6B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.
B250988C17
0.75,0.51 1.104,0.76 0.354,0.25 1.135,1.219 1.323,1.219 1.323,1.219 1.5,0.885 false 2.333,1.208 2.146,1.208 2.146,1.208 1.906,0.875 false 0.094,0.094 0.354,0.344 0.26,0.25 10 *a 0.771,3.177 0.979,3.375 0.208,0.198 10 *c 1.719,3.177 1.927,3.375 0.208,0.198 10 *d 0.104,1.427 0.688,1.875 0.583,0.448 10 *b 0.104,2.292 0.542,2.5 0.438,0.208 10 GND 0.667,1.135 1.271,1.375 0.604,0.24 10 ANTE6 2.396,1.125 2.938,1.302 0.542,0.177 10 CLGB 0.823,0.552 1.188,0.75 0.365,0.198 10 M18
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna [Rear Floor])
*b Waveform
*c Within approximately 30 seconds from when the door is closed
*d After approximately 30 seconds from when the door is closed


Disconnect the M18 No. 2 indoor electrical key antenna assembly (rear floor) connector.


b.

Connect the G83 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M18-1 (ANTE6) - M18-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

11.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Instrument Panel Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK KEY DIAGNOSTIC MODE
12.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.
B340887C01
0.688,1.052 2.385,0.208 2.385,0.208 2.573,0.208 false 1.688,1.052 2.385,0.208 false 2.615,0.115 2.927,0.313 0.313,0.198 10 *a
*a Inspection Point


Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the No. 2 indoor electrical key antenna assembly (rear floor). When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.CHECK HARNESS AND CONNECTOR (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


b.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M21-1 (ANTE7) - G83-9 (CLG7) Always Below 1 Ω
M21-3 (CLGB) - G83-8 (CG7B) Always Below 1 Ω
M21-1 (ANTE7) or G83-9 (CLG7) - Body ground Always 10 kΩ or higher
M21-3 (CLGB) or G83-8 (CG7B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA)
a.
B250988C18
0.792,0.51 1.156,0.76 0.365,0.25 1.135,1.219 1.323,1.219 1.323,1.219 1.5,0.885 false 2.333,1.208 2.146,1.208 2.146,1.208 1.906,0.875 false 0.094,0.094 0.354,0.344 0.26,0.25 10 *a 0.771,3.177 0.979,3.375 0.208,0.198 10 *c 1.719,3.177 2.021,3.427 0.302,0.25 10 *d 0.104,1.427 0.302,1.635 0.198,0.208 10 *b 0.115,2.281 0.552,2.49 0.438,0.208 10 GND 0.656,1.125 1.26,1.365 0.604,0.24 10 ANTE7 2.385,1.125 2.927,1.302 0.542,0.177 10 CLGB 0.823,0.552 1.188,0.75 0.365,0.198 10 M21
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna [Inside Luggage])
*b Waveform
*c Within approximately 30 seconds from when the door is closed
*d After approximately 30 seconds from when the door is closed


Disconnect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


b.

Connect the G83 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M21-1 (ANTE7) - M21-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

15.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK KEY DIAGNOSTIC MODE
16.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.
B340884C01
1.115,1.729 0.75,1.49 0.75,1.49 1.51,1.042 false 0.583,1.396 0.896,1.594 0.313,0.198 10 *a
*a Inspection Point


Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the No. 3 indoor electrical key antenna assembly (inside luggage). When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)