Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1269  Theft Deterrent ECU Communication Stop  B126A  Remote Engine Starter ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the accessory ECU and accessory BERKES.

This DTC is output when there is no communication between the main body ECU (multiplex network body ECU) and accessory ECU for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1269 Theft Deterrent ECU Communication Stop No communication between main body ECU (multiplex network body ECU) and accessory ECU (genuine auto alarm) (no communication for 10 seconds or more)
·

Main body ECU (multiplex network body ECU)

·

Option connector (accessory BERKES)

·

Wire harness and connector


B126A Remote Engine Starter ECU Communication Stop No communication between main body ECU (multiplex network body ECU) and accessory ECU (genuine remote engine starter) (no communication for 10 seconds or more)
·

Main body ECU (multiplex network body ECU)

·

Option connector (accessory BERKES)

·

Wire harness and connector



WIRING DIAGRAM

E342458E01
0.406,2.604 2.094,3.031 1.688,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 0.396,2.406 0.854,2.604 0.458,0.198 10 false G78 1.385,1.208 1.844,1.406 0.458,0.198 10 false BTX 1.792,1.094 2.104,1.292 0.313,0.198 10 false 25 1.365,1.771 1.823,1.969 0.458,0.198 10 false BRX 1.802,1.656 2.115,1.854 0.313,0.198 10 false 26 2.792,1.083 3.104,1.281 0.313,0.198 10 false 1 2.802,1.635 3.115,1.833 0.313,0.198 10 false 2 2.927,2.396 3.385,2.594 0.458,0.198 10 false G69 2.885,2.583 4.281,3.031 1.396,0.448 10 false Option Connector (Accessory BERKES) 3.042,1.208 3.5,1.406 0.458,0.198 10 false BRX2 3.031,1.771 3.49,1.969 0.458,0.198 10 false BTX2 5.198,2.438 6.229,2.719 1.031,0.281 10 false Accessory ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing repairs, make sure there are no malfunctions in the power source circuit of the accessory ECU. (For details, refer to the installation procedures of the accessory manual.)

·

When using the GTS with the ignition switch off, turn a door courtesy light switch assembly on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins.



HINT:

For the circuit diagram of the accessory ECU, refer to the installation manual wiring diagram of the accessory manual.


PROCEDURE

1.CHECK ACCESSORY ECU INSTALLATION
a.

Check if an accessory ECU (security ECU or remote engine starter ECU) is installed.


Result:
Result Proceed to
Part installed A
Part not installed B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - OPTION CONNECTOR)

B

3.INITIALIZE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - OPTION CONNECTOR)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the G69 connector of the option connector (accessory BERKES).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specification Condition
G78-25 (BTX) - G69-1 (BRX2) Always Below 1 Ω
G78-26 (BRX) - G69-2 (BTX2)
G78-25 (BTX) - Body ground Always 10 kΩ or higher
G78-26 (BRX) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE OPTION CONNECTOR (ACCESSORY BERKES) WITH NEW OR NORMALLY FUNCTIONING ONE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.INITIALIZE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
HINT:

When an accessory ECU (security ECU or remote engine starter ECU) connected to the main body ECU (multiplex network body ECU) is removed, initialize the main body ECU (multiplex network body ECU).


a.

Initialize ECU connection information

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Main Body / Utility / Initialize ECU Connection Information. Body Electrical

Body Electrical > Main Body > Utility
Tester Display
Initialization
50005 123 207


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B1269 and B126A are not output A
B1269 or B126A is output (for LHD) B
B1269 or B126A is output (for RHD) C



A

END

B

C