Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3090E _56 Audio / Visual / Telematics _057499 TELEMATICS _0279690 TELEMATICS SYSTEM J

TELEMATICS  TELEMATICS SYSTEM  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E353340E08
1.521,1.74 2.875,1.969 1.354,0.229 10 false Manual (SOS) Switch 1.125,2.156 1.448,2.354 0.323,0.198 10 false Q16 1.125,2.333 2.479,2.563 1.354,0.229 10 false Map Light Assembly 4.979,1.958 6.469,2.167 1.49,0.208 10 false Telematics Transceiver 4.969,1.771 5.292,1.969 0.323,0.198 10 false M38 3.417,0.667 3.823,0.854 0.406,0.188 10 false SLED 3.469,1.094 3.833,1.281 0.365,0.188 10 false GND 5.177,1.104 5.542,1.292 0.365,0.188 10 false SIG- 5.156,0.781 5.573,0.969 0.417,0.188 10 false SLED 4.958,0.688 5.104,0.906 0.146,0.219 10 false 9 4.896,1.094 5.104,1.333 0.208,0.24 10 false 26 3.896,0.667 4.104,0.906 0.208,0.24 10 false 2 3.885,1.104 4.094,1.344 0.208,0.24 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E303110C15
2.271,1.063 2.417,0.479 2.417,0.479 2.552,0.479 true 1.01,1.063 0.865,0.479 0.865,0.479 0.729,0.479 true 0.365,0.406 0.979,0.604 0.615,0.198 10 false GND 2.635,0.406 3.25,0.604 0.615,0.198 10 false SLED 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 4 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) from the batteries lead to terminal 2 (SLED) and a negative (-) lead to terminal 10 (GND) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch illuminates.

OK:

Manual (SOS) switch illuminates.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the M38 telematics transceiver connector.


b.

Disconnect the Q16 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-9 (SLED) - Q16-2 (SLED) Always Below 1 Ω
M38-26 (SIG-) - Q16-10 (GND) Always Below 1 Ω
M38-9 (SLED) or Q16-2 (SLED) - Body ground Always 10 kΩ or higher
M38-26 (SIG-) or Q16-10 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR