Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 13 CAN Junction Connector (w/ Seat Memory)

C235392C96
4.417,1.25 4.833,1.5 0.417,0.25 3.281,1.323 2.917,0.656 2.917,0.656 2.667,0.656 true 3.177,1.313 2.813,0.865 2.813,0.865 2.583,0.865 true 3.073,1.313 2.833,1.083 2.833,1.083 2.583,1.083 true 3.073,1.469 2.833,1.75 2.833,1.75 2.583,1.75 true 3.177,1.479 2.938,1.927 2.938,1.927 2.688,1.927 true 3.281,1.49 3.104,2.167 3.104,2.167 2.854,2.167 true 2.115,0.552 3.031,0.75 0.917,0.198 10 false CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.031,0.781 2.948,0.979 0.917,0.198 10 false CANH*c 2.021,0.99 2.938,1.188 0.917,0.198 10 false CANH*d 2.167,1.833 3.083,2.031 0.917,0.198 10 false CANL*c 2.063,1.646 2.979,1.844 0.917,0.198 10 false CANL*d 2.333,2.083 3.25,2.281 0.917,0.198 10 false CANL*b 4.479,1.302 5.396,1.5 0.917,0.198 10 false M39
*a Rear view of wire harness connector
(to No. 13 CAN Junction Connector)
*b for Main Body ECU (Multiplex Network Body ECU)
*c for No. 5 CAN Junction Connector *d for Position Control ECU and Switch Assembly


No. 13 CAN Junction Connector Wiring Color Connect to
M39-9 (CANH) B Main body ECU (multiplex network body ECU)
M39-20 (CANL) GR
M39-10 (CANH) P No. 5 CAN junction connector
M39-21 (CANL) GR
M39-11 (CANH) R Position control ECU and switch assembly
M39-22 (CANL) GR


b.

No. 5 CAN Junction Connector (w/ Power Back Door System)

C235392C97
4.417,1.25 4.833,1.5 0.417,0.25 3.375,1.313 2.917,0.667 2.917,0.667 2.667,0.667 true 3.271,1.313 2.813,0.865 2.813,0.865 2.583,0.865 true 3.188,1.333 2.833,1.083 2.833,1.083 2.583,1.083 true 3.198,1.479 2.833,1.75 2.833,1.75 2.583,1.75 true 3.271,1.49 2.938,1.927 2.938,1.927 2.688,1.927 true 3.365,1.49 3.104,2.167 3.104,2.167 2.854,2.167 true 2.115,0.552 3.031,0.75 0.917,0.198 10 false CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.031,0.781 2.948,0.979 0.917,0.198 10 false CANH*c 2.021,0.99 2.938,1.188 0.917,0.198 10 false CANH*d 2.167,1.833 3.083,2.031 0.917,0.198 10 false CANL*c 2.063,1.646 2.979,1.844 0.917,0.198 10 false CANL*d 2.333,2.083 3.25,2.281 0.917,0.198 10 false CANL*b 4.5,1.271 5.417,1.469 0.917,0.198 10 false N39
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b
·

for Main Body ECU (Multiplex Network Body ECU) (w/o Seat Memory)

·

for No. 13 CAN Junction Connector (w/ Seat Memory)


*c for Multiplex Network Door ECU *d for No. 1 CAN Junction Terminal


No. 5 CAN Junction Connector Wiring Color Connect to

*1: w/o Seat Memory

*2: w/ Seat Memory

N39-8 (CANH) B*1
P*2
·

Main body ECU (multiplex network body ECU)*1

·

No. 13 CAN junction connector*2


N39-19 (CANL) GR
N39-9 (CANH) G Multiplex network door ECU
N39-20 (CANL) GR
N39-10 (CANH) L No. 1 CAN junction terminal
N39-21 (CANL) GR


c.

No. 11 CAN Junction Connector

C235392C42
4.385,1.25 4.875,1.49 0.49,0.24 3.656,1.302 3.083,0.458 3.083,0.458 2.833,0.458 true 3.573,1.333 2.906,0.719 2.906,0.719 2.677,0.719 true 3.438,1.313 2.906,1 2.906,1 2.656,1 true 3.448,1.458 2.917,1.875 2.917,1.875 2.667,1.875 true 3.563,1.458 3.083,2.083 3.083,2.083 2.833,2.083 true 3.646,1.49 3.25,2.25 3.25,2.25 3,2.25 true 4.5,0.969 4.313,0.969 4.313,0.969 4.031,1.313 true 4.396,0.667 4.208,0.667 4.208,0.667 3.938,1.313 true 4.26,0.417 4.073,0.417 4.073,0.417 3.833,1.313 true 4.51,1.844 4.323,1.844 4.323,1.844 4.031,1.448 true 4.313,2.063 4.125,2.063 4.125,2.063 3.917,1.479 true 4.25,2.396 4.063,2.396 4.063,2.396 3.833,1.469 true 3.75,1.469 3.438,2.448 3.438,2.448 3.188,2.448 true 3.729,1.313 3.354,0.198 3.354,0.198 3.104,0.198 true 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.104,0.896 3.021,1.094 0.917,0.198 10 false CANH*h 2.656,2.354 3.573,2.552 0.917,0.198 10 false CANL*e 2.135,1.76 3.052,1.958 0.917,0.198 10 false CANL*h 4.313,2.271 5.229,2.469 0.917,0.198 10 false CANL*d 4.448,1.271 5.365,1.469 0.917,0.198 10 false G188 4.563,0.865 5.479,1.063 0.917,0.198 10 false CANH*b 4.438,0.573 5.354,0.771 0.917,0.198 10 false CANH*c 4.302,0.313 5.219,0.51 0.917,0.198 10 false CANH*d 4.573,1.719 5.49,1.917 0.917,0.198 10 false CANL*b 4.365,1.948 5.281,2.146 0.917,0.198 10 false CANL*c 2.542,0.104 3.458,0.302 0.917,0.198 10 false CANH*e 2.313,1.948 3.229,2.146 0.917,0.198 10 false CANL*g 2.323,0.375 3.24,0.573 0.917,0.198 10 false CANH*f 2.146,0.625 3.063,0.823 0.917,0.198 10 false CANH*g 2.5,2.146 3.417,2.344 0.917,0.198 10 false CANL*f
*a Rear view of wire harness connector
(to No. 11 CAN Junction Connector)
*b for Main Body ECU (Multiplex Network Body ECU)
*c for Air Conditioning Amplifier Assembly *d for Brake Actuator Assembly (Skid Control ECU)
*e for No. 12 CAN Junction Connector *f for Engine Stop and Start ECU (w/ Stop and Start System)
*g for Airbag Sensor Assembly *h for ECM


No. 11 CAN Junction Connector Wiring Color Connect to

*: w/ Stop and Start System

G188-1 (CANH) G Main body ECU (multiplex network body ECU)
G188-12 (CANL) W
G188-2 (CANH) B Air conditioning amplifier assembly
G188-13 (CANL) W
G188-3 (CANH) GR Brake actuator assembly (skid control ECU)
G188-14 (CANL) W
G188-4 (CANH) V No. 12 CAN junction connector
G188-15 (CANL) W
G188-5 (CANH) LG Engine stop and start ECU*
G188-16 (CANL) W
G188-6 (CANH) BR Airbag sensor assembly
G188-17 (CANL) W
G188-7 (CANH) Y ECM
G188-18 (CANL) W


d.

No. 12 CAN Junction Connector

C235392C76
4.385,1.25 4.875,1.49 0.49,0.24 3.552,1.302 2.979,0.458 2.979,0.458 2.729,0.458 true 3.375,1.333 2.906,0.719 2.906,0.719 2.677,0.719 true 3.188,1.333 2.823,1.156 2.823,1.156 2.573,1.156 true 3.188,1.448 2.844,1.74 2.844,1.74 2.594,1.74 true 3.354,1.458 2.885,1.979 2.885,1.979 2.635,1.979 true 3.552,1.448 3.156,2.208 3.156,2.208 2.906,2.208 true 4.5,0.969 4.313,0.969 4.313,0.969 4.031,1.313 true 4.396,0.667 4.208,0.667 4.208,0.667 3.938,1.313 true 4.26,0.417 4.073,0.417 4.073,0.417 3.75,1.313 true 4.51,1.844 4.323,1.844 4.323,1.844 4.031,1.448 true 4.313,2.063 4.125,2.063 4.125,2.063 3.917,1.479 true 4.25,2.396 4.063,2.396 4.063,2.396 3.75,1.479 true 3.667,1.448 3.417,2.396 3.417,2.396 3.167,2.396 true 3.667,1.323 3.24,0.229 3.24,0.229 2.99,0.229 true 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.635,2.281 3.552,2.479 0.917,0.198 10 false CANL*e 2.063,1.625 2.979,1.823 0.917,0.198 10 false CANL*h 4.313,2.271 5.229,2.469 0.917,0.198 10 false CANL*d 4.448,1.271 5.365,1.469 0.917,0.198 10 false G189 4.563,0.865 5.479,1.063 0.917,0.198 10 false CANH*b 4.438,0.573 5.354,0.771 0.917,0.198 10 false CANH*c 4.302,0.313 5.219,0.51 0.917,0.198 10 false CANH*d 4.573,1.719 5.49,1.917 0.917,0.198 10 false CANL*b 4.365,1.948 5.281,2.146 0.917,0.198 10 false CANL*c 2.448,0.104 3.365,0.302 0.917,0.198 10 false CANH*e 2.094,1.844 3.01,2.042 0.917,0.198 10 false CANL*g 2.146,0.625 3.063,0.823 0.917,0.198 10 false CANH*g 2.417,2.094 3.333,2.292 0.917,0.198 10 false CANL*f 2.219,0.344 3.135,0.542 0.917,0.198 10 false CANH*f 2.031,1.021 2.948,1.219 0.917,0.198 10 false CANH*h
*a Rear view of wire harness connector
(to No. 12 CAN Junction Connector)
*b for Combination Meter Assembly
*c for Power Steering ECU Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*e for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *f for 4WD ECU Assembly (for 4WD/AWD)
*g for No. 11 CAN Junction Connector *h for Central Gateway ECU


No. 12 CAN Junction Connector Wiring Color Connect to

*1: w/ Entry and Start System

*2: for 4WD/AWD

G189-1 (CANH) G Combination meter assembly
G189-12 (CANL) W
G189-2 (CANH) LG Power steering ECU assembly
G189-13 (CANL) W
G189-4 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
G189-15 (CANL) W
G189-5 (CANH) R Certification ECU (smart key ECU assembly)*1
G189-16 (CANL) W
G189-6 (CANH) GR 4WD ECU assembly*2
G189-17 (CANL) W
G189-8 (CANH) V No. 11 CAN junction connector
G189-19 (CANL) W
G189-10 (CANH) SB Central gateway ECU
G189-21 (CANL) W


e.

No. 8 CAN Junction Connector

C235392C44
4.417,1.25 4.833,1.5 0.417,0.25 3.656,1.302 3.083,0.458 3.083,0.458 2.833,0.458 true 3.573,1.333 2.906,0.719 2.906,0.719 2.677,0.719 true 3.438,1.313 2.906,1 2.906,1 2.656,1 true 3.448,1.458 2.917,1.875 2.917,1.875 2.667,1.875 true 3.563,1.458 3.083,2.083 3.083,2.083 2.833,2.083 true 3.646,1.49 3.25,2.25 3.25,2.25 3,2.25 true 4.5,0.969 4.313,0.969 4.313,0.969 4.031,1.313 true 4.396,0.667 4.208,0.667 4.208,0.667 3.833,1.323 true 4.26,0.417 4.073,0.417 4.073,0.417 3.74,1.302 true 4.51,1.844 4.323,1.844 4.323,1.844 4.031,1.448 true 4.313,2.063 4.125,2.063 4.125,2.063 3.823,1.469 true 4.188,2.229 4,2.229 4,2.229 3.74,1.469 true 2.25,0.323 3.167,0.521 0.917,0.198 10 false CANH*d 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.125,0.583 3.042,0.781 0.917,0.198 10 false CANH*e 2.104,0.896 3.021,1.094 0.917,0.198 10 false CANH*f 2.302,1.958 3.219,2.156 0.917,0.198 10 false CANL*e 2.135,1.76 3.052,1.958 0.917,0.198 10 false CANL*f 2.438,2.146 3.354,2.344 0.917,0.198 10 false CANL*d 4.458,1.271 5.375,1.469 0.917,0.198 10 false G173 4.563,0.865 5.479,1.063 0.917,0.198 10 false CANH*b 4.438,0.573 5.354,0.771 0.917,0.198 10 false CANH*c 4.302,0.313 5.219,0.51 0.917,0.198 10 false CANH*c 4.573,1.719 5.49,1.917 0.917,0.198 10 false CANL*b 4.365,1.948 5.281,2.146 0.917,0.198 10 false CANL*c 4.229,2.125 5.146,2.323 0.917,0.198 10 false CANL*c
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b
·

for Navigation Receiver Assembly (w/ Navigation System)

·

for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])


*c for Central Gateway ECU *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e for Forward Recognition Camera (w/ Pre-crash Safety System) *f for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)


No. 8 CAN Junction Connector Wiring Color Connect to

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

*3: w/ Pre-crash Safety System

G173-1 (CANH) Y
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G173-12 (CANL) W
G173-3 (CANH) R Central gateway ECU
G173-14 (CANL) W
G173-4 (CANH) V Central gateway ECU
G173-15 (CANL) W
G173-5 (CANH) B Driving support ECU assembly*3
G173-16 (CANL) W
G173-6 (CANH) L Forward recognition camera*3
G173-17 (CANL) W
G173-7 (CANH) SB Millimeter wave radar sensor assembly*3
G173-18 (CANL) W


f.

No. 9 CAN Junction Connector

C343209C15
0.833,0.771 1.333,1.021 0.5,0.25 2.188,0.646 2.375,0.646 2.375,0.646 2.635,0.885 true 2.375,0.438 2.563,0.438 2.563,0.438 2.813,0.865 true 2.625,0.26 2.813,0.26 2.813,0.26 3.021,0.865 true 2.865,0.135 3.052,0.135 3.052,0.135 3.208,0.854 true 2.24,1.198 2.427,1.198 2.427,1.198 2.656,1.042 true 2.354,1.406 2.542,1.406 2.542,1.406 2.823,1.031 true 2.531,1.573 2.719,1.573 2.719,1.573 3.01,1.021 true 3.177,1.573 3.031,1.573 3.031,1.573 3.208,1.01 true 3.875,0.125 3.688,0.125 3.688,0.125 3.427,0.854 true 4.24,0.396 4.052,0.396 4.052,0.396 3.771,0.854 true 4.354,1.344 4.167,1.344 4.167,1.344 3.729,1.01 true 4.188,1.635 4,1.635 4,1.635 3.427,1.021 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.615,0.552 2.229,0.76 0.615,0.208 10 false CANH*b 1.823,0.333 2.438,0.542 0.615,0.208 10 false CANH*c 2.073,0.156 2.688,0.365 0.615,0.208 10 false CANH*d 2.302,0.01 2.917,0.219 0.615,0.208 10 false CANH*e 3.938,0.031 4.552,0.24 0.615,0.208 10 false CANH*f 4.271,0.292 4.885,0.5 0.615,0.208 10 false CANH*g 1.688,1.063 2.302,1.271 0.615,0.208 10 false CANL*b 1.813,1.302 2.427,1.51 0.615,0.208 10 false CANL*c 1.99,1.469 2.604,1.677 0.615,0.208 10 false CANL*d 3.219,1.458 3.833,1.667 0.615,0.208 10 false CANL*e 4.25,1.531 4.865,1.74 0.615,0.208 10 false CANL*f 4.427,1.24 5.042,1.448 0.615,0.208 10 false CANL*g 0.917,0.792 1.375,0.99 0.458,0.198 10 false G174
*a Front view of wire harness connector
(to No. 9 CAN Junction Connector)
*b for Forward Recognition Camera (w/ Pre-crash Safety System)
*c for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e for Central Gateway ECU *f for No. 10 CAN Junction Connector
*g for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type]) - -


No. 9 CAN Junction Connector Wiring Color Connect to

*1: w/ Pre-crash Safety System

*2: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

G174-1 (CANH) G Forward recognition camera*1
G174-11 (CANL) LG
G174-2 (CANH) B Millimeter wave radar sensor assembly*1
G174-12 (CANL) LG
G174-3 (CANH) P Driving support ECU assembly*1
G174-13 (CANL) LG
G174-4 (CANH) Y Central gateway ECU
G174-14 (CANL) LG
G174-5 (CANH) L No. 10 CAN junction connector
G174-15 (CANL) LG
G174-6 (CANH) R Clearance warning ECU assembly*2
G174-16 (CANL) LG


g.

No. 10 CAN Junction Connector

C343209C35
0.833,0.771 1.333,1.021 0.5,0.25 2.188,0.646 2.375,0.646 2.375,0.646 2.823,0.885 true 2.375,0.438 2.563,0.438 2.563,0.438 3,0.854 true 2.24,1.198 2.427,1.198 2.427,1.198 2.823,1.042 true 2.333,1.406 2.521,1.406 2.521,1.406 3.021,1 true 4.021,0.354 3.833,0.354 3.833,0.354 3.427,0.865 true 3.854,1.385 3.667,1.385 3.667,1.385 3.396,1.031 true 2.667,0.24 2.854,0.24 2.854,0.24 3.198,0.885 true 2.594,1.573 2.781,1.573 2.781,1.573 3.229,1.021 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.615,0.552 2.229,0.76 0.615,0.208 10 false CANH*b 1.823,0.333 2.438,0.542 0.615,0.208 10 false CANH*c 2.073,0.156 2.688,0.365 0.615,0.208 10 false CANH*d 4.083,0.25 4.698,0.458 0.615,0.208 10 false CANH*e 1.688,1.083 2.302,1.292 0.615,0.208 10 false CANL*b 1.792,1.292 2.406,1.5 0.615,0.208 10 false CANL*c 2.052,1.479 2.667,1.688 0.615,0.208 10 false CANL*d 3.917,1.271 4.531,1.479 0.615,0.208 10 false CANL*e 0.958,0.792 1.417,0.99 0.458,0.198 10 false N36
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b for Central Gateway ECU
*c for No. 9 CAN Junction Connector *d for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System)
*e for Television Camera Assembly (w/ Parking Assist Monitor System [for Camera built-in ECU]) - -


No. 10 CAN Junction Connector Wiring Color Connect to

*1: w/ Blind Spot Monitor System

*2: w/ Parking Assist Monitor System (for Camera built-in ECU)

N36-2 (CANH) V Central gateway ECU
N36-12 (CANL) LG
N36-3 (CANH) L No. 9 CAN junction connector
N36-13 (CANL) LG
N36-4 (CANH) R Blind spot monitor sensor LH*1
N36-14 (CANL) LG
N36-5 (CANH) P Television camera assembly*2
N36-15 (CANL) LG


h.
C210060C41
0.271,0.969 0.688,1.219 0.417,0.25 1.646,0.219 1.5,0.219 1.5,0.219 1.354,0.885 true 2.167,0.458 2.021,0.458 2.021,0.458 1.719,0.885 true 1.688,0.104 2.25,0.281 0.563,0.177 10 false CANH*b 0.354,1 0.656,1.177 0.302,0.177 10 false N31 2.219,0.344 2.781,0.521 0.563,0.177 10 false CANL*b 0.156,0.115 0.719,0.292 0.563,0.177 10 false *a
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b for No. 5 CAN Junction Connector


No. 1 CAN Junction Terminal (w/ Power Back Door System)

No. 1 CAN Junction Terminal Wiring Color Connect to
N31-2 (CANL) GR No. 5 CAN junction connector
N31-3 (CANH) L



CHECK DLC3


a.
C253362C06
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.052 0.708,1.25 0.458,0.198 10 G14 0.75,0.417 1.208,0.615 0.458,0.198 10 CG 2.469,0.344 2.927,0.542 0.458,0.198 10 CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 66 Ω
G14-6 (CANH) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-6 (CANH) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU


C331365C13
3.281,0.313 3.76,0.573 0.479,0.26 5.094,0.938 4.823,0.938 4.823,0.938 4.188,1.344 true 2.333,0.865 2.563,0.865 2.563,0.865 2.948,1.354 true 4.375,2.083 4.104,2.083 4.104,2.083 3.854,1.458 true 4.021,2.552 3.75,2.552 3.75,2.552 3.542,1.448 true 4.635,0.646 4.365,0.646 4.365,0.646 3.885,1.354 true 4.552,0.375 4.281,0.375 4.281,0.375 3.688,1.438 true 4.438,0.135 4.167,0.135 4.167,0.135 3.625,1.438 true 4.24,2.302 3.969,2.302 3.969,2.302 3.781,1.438 true 1.979,1.906 2.208,1.906 2.208,1.906 2.979,1.448 true 2.396,2.208 2.625,2.208 2.625,2.208 3.271,1.448 true 2.729,2.448 2.958,2.448 2.958,2.448 3.375,1.438 true 2.927,2.646 3.156,2.646 3.156,2.646 3.448,1.438 true 2.5,0.635 2.729,0.635 2.729,0.635 3.031,1.375 true 2.729,0.385 2.958,0.385 2.958,0.385 3.25,1.365 true 3.354,0.344 3.969,0.542 0.615,0.198 10 false G170 5.156,0.833 5.594,1.042 0.438,0.208 10 false BATT 1.99,0.781 2.427,0.99 0.438,0.208 10 false GND 4.427,1.969 5.042,2.177 0.615,0.208 10 false CA6H*D 2.167,2.344 2.802,2.552 0.635,0.208 10 false CAYL*B 4.49,0.042 5.094,0.25 0.604,0.208 10 false CA4L*A 4.083,2.49 4.74,2.708 0.656,0.219 10 false CA4H*A 4.688,0.542 5.281,0.771 0.594,0.229 10 false CA6L*D 4.292,2.198 4.906,2.406 0.615,0.208 10 false CA5H*C 4.594,0.281 5.208,0.49 0.615,0.208 10 false CA5L*C 2.396,2.531 3.031,2.74 0.635,0.208 10 false CAYH*B 1.885,2.104 2.479,2.323 0.594,0.219 10 false CA3L*B 1.458,1.802 2.073,2.01 0.615,0.208 10 false CAXL*C 1.938,0.531 2.552,0.74 0.615,0.208 10 false CAXH*C 2.188,0.281 2.802,0.49 0.615,0.208 10 false CA3H*B
*A Bus 2 *B Bus 3
*C Bus 5 *D V Bus


a.
C343190C06
1.667,0.208 2.198,0.458 0.531,0.25 1.094,1.875 1.24,1.875 1.24,1.875 1.667,1.271 true 1.323,2.052 1.469,2.052 1.469,2.052 1.771,1.271 true 2.646,0.26 2.49,0.26 2.49,0.26 2.125,1.115 true 2.823,0.729 2.667,0.729 2.667,0.729 2.469,1.115 true 2.844,1.542 2.729,1.542 2.729,1.542 2.563,1.281 true 0.719,0.677 0.865,0.677 0.865,0.677 1.302,1.094 true 0.927,0.458 1.073,0.458 1.073,0.458 1.573,1.26 true 1.219,0.198 1.365,0.198 1.365,0.198 1.854,1.271 true 2.396,2.063 2.26,2.063 2.26,2.063 1.958,1.271 true 2.646,1.833 2.51,1.833 2.51,1.833 2.063,1.271 true 2.906,1.021 2.75,1.021 2.75,1.021 2.604,1.115 true 0.448,1.344 0.594,1.344 0.594,1.344 0.823,1.115 true 0.667,1.688 0.813,1.688 0.813,1.688 1.479,1.271 true 0.615,0.865 0.76,0.865 0.76,0.865 1.365,1.271 true 1.771,0.25 2.188,0.427 0.417,0.177 10 false G170 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 0.781,1.938 1.375,2.167 0.594,0.229 10 false CA4H*A 0.563,1.781 1.156,2.01 0.594,0.229 10 false CA4L*A 2.719,0.135 3.313,0.365 0.594,0.229 10 false CA3H*B 2.875,0.615 3.427,0.844 0.552,0.229 10 false CAXH*C 2.885,1.438 3.396,1.698 0.51,0.26 10 false CAXL*C 0.396,0.344 0.906,0.604 0.51,0.26 10 false CA5L*C 0.177,0.573 0.76,0.823 0.583,0.25 10 false CA6L*D 0.656,0.104 1.229,0.365 0.573,0.26 10 false CAYH*B 2.438,1.958 3.01,2.156 0.573,0.198 10 false CAYL*B 2.698,1.719 3.292,1.948 0.594,0.229 10 false CA3L*B 2.958,0.938 3.354,1.208 0.396,0.271 10 false GND 0.104,1.25 0.563,1.521 0.458,0.271 10 false BATT 0.094,1.573 0.677,1.823 0.583,0.25 10 false CA5H*C 0.063,0.792 0.646,1.042 0.583,0.25 10 false CA6H*D
*A Bus 2
*B Bus 3
*C Bus 5
*D V Bus
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Bus 2
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-18 (CA4H) - G170-17 (CA4L) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G170-18 (CA4H) - G170-10 (GND) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-17 (CA4L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-18 (CA4H) - G170-1 (BATT) SB - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-17 (CA4L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-6 (CA3H) - G170-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-21 (CA3L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-6 (CA3H) - G170-1 (BATT) R - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-21 (CA3L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-19 (CAYH) - G170-20 (CAYL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-19 (CAYH) - G170-10 (GND) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-20 (CAYL) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-19 (CAYH) - G170-1 (BATT) V - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-20 (CAYL) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-15 (CA5H) - G170-16 (CA5L) Y - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-15 (CA5H) - G170-10 (GND) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-16 (CA5L) - G170-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-15 (CA5H) - G170-1 (BATT) Y - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-16 (CA5L) - G170-1 (BATT) LG - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-9 (CAXH) - G170-24 (CAXL) V - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-9 (CAXH) - G170-10 (GND) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-24 (CAXL) - G170-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-9 (CAXH) - G170-1 (BATT) V - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-24 (CAXL) - G170-1 (BATT) LG - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G170-14 (CA6H) - G170-10 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-5 (CA6L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-14 (CA6H) - G170-1 (BATT) B - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-5 (CA6L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


a.

for 2AR-FE:

C228683E02
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 4.781,1.031 4.448,0.365 4.448,0.365 4.229,0.365 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.667,1.042 2.365,0.51 2.365,0.51 2.125,0.51 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B77 3.823,0.292 4.5,0.5 0.677,0.208 10 CANH 3.865,0.542 4.542,0.75 0.677,0.208 10 CANL 1.906,0.438 2.365,0.635 0.458,0.198 10 E1 6.76,0.521 7.156,0.677 0.396,0.156 10 BATT

i.

Disconnect the ECM connectors.

C229008C05
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.604,1.448 2.948,2.115 2.948,2.115 3.135,2.115 true 2.594,1.365 2.885,0.927 2.885,0.927 3.094,0.927 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.844 0.75,1.083 0.406,0.24 10 BATT 3.135,0.844 3.635,1.094 0.5,0.25 10 CANH 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 4.063,0.667 4.469,0.906 0.406,0.24 10 E1 4.833,0.625 5.24,0.865 0.406,0.24 10 B77 3.156,2.042 3.656,2.292 0.5,0.25 10 CANL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B77-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B77-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.

for 3ZR-FAE, 3ZR-FE:

C228683C19
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.396 2.896,0.646 0.458,0.25 2.438,0.083 2.896,0.333 0.458,0.25 4.802,1.042 4.448,0.417 4.448,0.417 4.229,0.417 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.688,1.042 2.188,0.573 2.188,0.573 1.948,0.573 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 1.948,2.271 1.771,2.271 1.771,2.271 1.104,1.156 true 5.385,0.292 5.844,0.49 0.458,0.198 10 false A62 2.552,0.115 3.01,0.313 0.458,0.198 10 false B93 3.781,0.292 4.458,0.5 0.677,0.208 10 false CANH 3.854,0.521 4.531,0.729 0.677,0.208 10 false CANL 1.583,0.458 2.427,0.635 0.844,0.177 10 false E1*D 6.76,0.49 7.156,0.646 0.396,0.156 10 false BATT 2.01,2.156 3.708,2.354 1.698,0.198 10 false E1*A, *B, *C 2.542,0.406 3,0.604 0.458,0.198 10 false B75 2.938,0.417 3.396,0.615 0.458,0.198 10 false *D 2.948,0.115 3.625,0.417 0.677,0.302 10 false *A, *B, *C
*A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
*C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)


i.

Disconnect the ECM connectors.

C229008C52
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 4.771,0.25 5.188,0.5 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.615,1.448 2.896,1.646 2.896,1.646 3.083,1.646 true 2.615,1.375 2.865,1.125 2.865,1.125 3.073,1.125 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 5.958,1.51 5.563,2.313 5.563,2.313 5.406,2.313 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.354,0.833 0.76,1.073 0.406,0.24 10 false BATT 3.115,1.031 3.688,1.281 0.573,0.25 10 false CANH 1.74,0.542 2.146,0.781 0.406,0.24 10 false A62 3.875,0.656 4.635,0.865 0.76,0.208 10 false E1*D 4.865,0.604 5.271,0.844 0.406,0.24 10 false B75 3.135,1.542 3.76,1.792 0.625,0.25 10 false CANL 4.542,2.208 5.781,2.417 1.24,0.208 10 false E1*A, *B, *C 5.26,0.604 5.667,0.844 0.406,0.24 10 false *D 4.854,0.271 5.26,0.51 0.406,0.24 10 false B93 5.26,0.281 6.01,0.542 0.75,0.26 10 false *A, *B, *C
*A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
*C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

for 3ZR-FAE
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, Manual Transaxle System
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, CVT (K114)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, CVT (K111)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B75-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

for 2WW:

C228683C18
5.281,0.26 5.74,0.51 0.458,0.25 4.885,1.146 4.615,0.333 4.615,0.333 4.396,0.333 true 4.781,1.135 4.365,0.604 4.365,0.604 4.24,0.604 true 5.99,1.146 6.469,0.604 6.469,0.604 6.719,0.604 true 5.781,1.052 6.125,0.344 6.125,0.344 6.375,0.344 true 5.385,0.292 5.844,0.49 0.458,0.198 10 false A62 3.823,0.51 4.5,0.719 0.677,0.208 10 false CANH 3.99,0.24 4.667,0.448 0.677,0.208 10 false CANL 6.438,0.229 6.896,0.427 0.458,0.198 10 false E1 6.76,0.49 7.156,0.646 0.396,0.156 10 false BATT

i.
C300832C23
1.448,0.302 1.865,0.583 0.417,0.281 2.219,1.323 2.5,0.615 2.5,0.615 2.646,0.615 true 2.302,1.323 2.677,1.052 2.677,1.052 2.823,1.052 true 0.938,0.604 1.115,0.604 1.115,0.604 1.427,1.26 true 0.479,0.833 0.656,0.833 0.656,0.833 1.219,1.344 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.875,0.948 3.333,1.104 0.458,0.156 10 false CANH 2.688,0.531 3.156,0.688 0.469,0.156 10 false CANL 1.542,0.344 1.875,0.49 0.333,0.146 10 false A62 0.719,0.49 1.031,0.688 0.313,0.198 10 false E1 0.125,0.74 0.542,0.958 0.417,0.219 10 false BATT
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-26 (CANH) - A62-25 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-26 (CANH) - A62-4 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-25 (CANL) - A62-4 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANH) - A62-15 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-25 (CANL) - A62-15 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



d.

for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF:

C159489E30
2.344,0.385 2.76,0.656 0.417,0.271 4.781,0.458 5.198,0.729 0.417,0.271 5.094,1.073 5.563,0.469 5.563,0.469 5.729,0.469 true 5.781,1.188 6.229,1.438 6.229,1.438 6.417,1.438 true 5.24,1.073 5.75,0.667 5.75,0.667 5.917,0.667 true 1.219,1.99 1,2.156 1,2.156 0.74,2.156 true 4.885,0.49 5.354,0.688 0.469,0.198 10 false A61 2.438,0.438 2.906,0.635 0.469,0.198 10 false B76 5.958,0.552 6.656,0.75 0.698,0.198 10 false CANL 5.771,0.365 6.469,0.563 0.698,0.198 10 false CANH 6.479,1.365 7.021,1.563 0.542,0.198 10 false BATT 0.542,2.063 1.083,2.26 0.542,0.198 10 false E1

i.

Disconnect the ECM connectors.

C234869C12
0.323,1.354 0.792,1.625 0.469,0.271 4.542,0.51 5.01,0.781 0.469,0.271 1.458,0.833 1.677,0.833 1.677,0.833 1.958,1.188 true 2.917,0.823 2.781,0.823 2.781,0.823 2.438,1.208 true 6.125,2.188 5.823,2.188 5.823,2.188 5.667,1.813 true 2.75,0.531 2.615,0.531 2.615,0.531 2.344,1.208 true 0.448,1.396 0.74,1.573 0.292,0.177 10 false A61 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 1.104,0.74 1.531,0.906 0.427,0.167 10 false BATT 2.958,0.719 3.823,0.885 0.865,0.167 10 false CANH 6.177,2.073 7.042,2.24 0.865,0.167 10 false E1 4.656,0.531 4.99,0.708 0.333,0.177 10 false B76 2.802,0.417 3.667,0.583 0.865,0.167 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A61-7 (CANH) - B76-109 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-6 (CANL) - B76-109 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-7 (CANH) - A61-2 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A61-6 (CANL) - A61-2 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278790C01
2.51,5.542 2.927,5.792 0.417,0.25 1.333,7.385 1.75,7.635 0.417,0.25 3.333,7.385 3.75,7.635 0.417,0.25 1.302,3.656 1.719,3.906 0.417,0.25 3.875,5.792 4.167,6.25 4.167,6.25 4.333,6.25 true 3.167,6.198 3.417,6.198 3.417,6.198 3.781,5.781 true 3.49,8.188 3.833,8.583 3.833,8.583 4,8.583 true 3,8.583 3.167,8.583 3.167,8.583 3.396,8.177 true 1.271,8.583 1.438,8.583 1.438,8.583 1.667,8.177 true 1.771,8.156 2.052,7.583 2.052,7.583 2.219,7.583 true 1.25,4.844 1.5,4.844 false 1.25,7.042 1.5,7.042 false 2.417,3.417 2.583,3.417 2.583,3.417 3,3.781 true 5.333,3.417 5.167,3.417 5.167,3.417 4.771,3.771 true 0.25,4.26 0.917,4.417 0.667,0.156 10 *A 0.25,6.604 0.563,6.76 0.313,0.156 10 *B 2.604,6.115 3.25,6.354 0.646,0.24 10 CANH*C 2.25,7.51 2.833,7.833 0.583,0.323 10 CANP*D 1.083,4.76 1.396,4.917 0.313,0.156 10 *1 4.396,6.167 5.042,6.406 0.646,0.24 10 CANL*C 0.708,8.5 1.375,8.74 0.667,0.24 10 CANN*D 2.583,5.583 2.896,5.74 0.313,0.156 10 G78 3.417,7.427 3.729,7.583 0.313,0.156 10 G78 4.063,8.51 4.708,8.75 0.646,0.24 10 CANL*C 2.438,8.5 3.083,8.75 0.646,0.25 10 CANH*C 1.406,7.427 1.719,7.583 0.313,0.156 10 G79 1.073,6.969 1.385,7.125 0.313,0.156 10 *1 1.469,3.698 2.135,3.854 0.667,0.156 10 A 2,3.344 2.646,3.583 0.646,0.24 10 GND1 5.417,3.344 6.063,3.583 0.646,0.24 10 BECU 2.667,1.667 3.333,1.823 0.667,0.156 10 A
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B Main Body ECU (Multiplex Network Body ECU) with 3 Connectors
*C Bus 2 *D Sub Bus 1
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL

C279368C01
5.385,0.385 5.771,0.656 0.385,0.271 2.26,0.333 2.646,0.604 0.385,0.271 0.073,0.292 0.458,0.563 0.385,0.271 4.938,0.771 5.083,0.771 5.083,0.771 5.281,1.021 true 6.313,0.771 6.458,0.771 6.458,0.771 6.656,1.021 true 0.979,0.948 1.333,1.438 1.333,1.438 1.531,1.438 true 0.927,0.948 1.219,1.625 1.219,1.625 1.417,1.625 true 3.292,0.958 3.646,1.448 3.646,1.448 3.844,1.448 true 3.25,0.969 3.542,1.646 3.542,1.646 3.74,1.646 true 1.448,1.552 2.104,1.771 0.656,0.219 10 CANH*A 3.875,1.354 4.521,1.594 0.646,0.24 10 CANP*B 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 4.271,0.094 4.583,0.25 0.313,0.156 10 *b 3.771,1.563 4.458,1.771 0.688,0.208 10 CANN*B 1.563,1.354 2.156,1.677 0.594,0.323 10 CANL*A 4.542,0.688 5.188,0.927 0.646,0.24 10 GND1 5.917,0.698 6.563,0.938 0.646,0.24 10 BECU 5.531,0.438 5.844,0.594 0.313,0.156 10 A 2.333,0.375 2.74,0.646 0.406,0.271 10 G79 0.146,0.344 0.552,0.615 0.406,0.271 10 G78
*A Bus 2 *B Sub Bus 1
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Bus 2
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G78-14 (CANH) - A-11 (GND1) G - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-13 (CANL) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-14 (CANH) - A-30 (BECU) G - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G78-13 (CANL) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) B - GR HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G79-9 (CANP) - A-11 (GND1) B - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-10 (CANN) - A-11 (GND1) GR - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-9 (CANP) - A-30 (BECU) B - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G79-10 (CANN) - A-30 (BECU) GR - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130E26
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.438,1.229 2.188,1.427 2.188,1.427 2.063,1.427 true 3.375,1.208 3.146,1.646 3.146,1.646 3.021,1.646 true 3.51,1.208 3.698,1.615 3.698,1.615 3.885,1.615 true 3.438,0.323 3.719,0.49 0.281,0.167 10 G16 5.01,1.479 5.271,1.667 0.26,0.188 10 ET 1.906,1.344 2.042,1.531 0.135,0.188 10 B 2.604,1.563 3.021,1.729 0.417,0.167 10 CANH 3.927,1.531 4.354,1.688 0.427,0.156 10 CANL

a.
C240157C07
1.531,0.146 1.969,0.458 0.438,0.313 1.719,1.219 2.26,1.76 2.26,1.76 2.49,1.76 true 1.635,1.219 1.375,1.844 1.375,1.844 1.135,1.844 true 0.979,1.219 0.781,1.083 0.781,1.083 0.604,1.083 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 1.625,0.229 2.083,0.427 0.458,0.198 10 G16 0.719,1.75 1.177,1.948 0.458,0.198 10 CANH 2.531,1.667 3.01,1.865 0.479,0.198 10 CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 ET 0.49,1.021 0.854,1.281 0.365,0.26 10 B
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G16-32 (CANH) - G16-21 (ET) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-31 (CANL) - G16-21 (ET) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-32 (CANH) - G16-40 (B) G - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G16-31 (CANL) - G16-40 (B) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


C123353E89
2.24,0.542 2.583,0.885 0.344,0.344 3.146,1.583 3.458,0.708 3.458,0.708 3.604,0.708 true 3.323,2 3.469,2.479 3.469,2.479 3.615,2.479 true 2.813,2.021 2.396,2.49 2.396,2.49 2.24,2.49 true 2.271,0.635 2.625,0.833 0.354,0.198 10 false G92 3.688,0.635 4.302,0.833 0.615,0.198 10 false CANH 3.677,2.406 4.292,2.604 0.615,0.198 10 false CANL 2,2.417 2.615,2.615 0.615,0.198 10 false E1

a.
C227529C03
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 BAT 1,1.604 1.542,1.813 0.542,0.208 10 E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G92-13 (CANH) - G92-22 (CANL) BR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G92-13 (CANH) - G92-25 (E1) BR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-22 (CANL) - G92-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-13 (CANH) - G14-16 (BAT) BR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G92-22 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


C306841E10
3.271,0.188 3.844,0.427 0.573,0.24 1.552,0.781 1.698,0.781 1.698,0.781 2.125,1.115 true 2.271,0.385 2.417,0.385 2.417,0.385 2.927,1.104 true 2.083,2.396 2.281,2.396 2.281,2.396 2.896,1.385 true 4.958,1.646 5.396,2.156 5.396,2.156 5.594,2.156 true 3.417,0.25 3.792,0.448 0.375,0.198 10 false A100 5.688,2.073 6.219,2.313 0.531,0.24 10 false GND1 1.896,0.281 2.427,0.521 0.531,0.24 10 false CANL 1.646,2.302 2.177,2.542 0.531,0.24 10 false CANH 1.302,0.656 1.833,0.896 0.531,0.24 10 false BM

a.
C321017C57
0.094,0.969 0.531,1.198 0.438,0.229 2.49,0.958 2.781,0.49 2.781,0.49 2.979,0.49 true 2.073,1.094 1.865,1.865 1.865,1.865 1.677,1.865 true 2.073,0.979 1.813,0.354 1.813,0.354 1.656,0.354 true 0.906,1.219 0.667,1.76 0.667,1.76 0.51,1.76 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 3.042,0.375 3.333,0.656 0.292,0.281 10 false BM 0.146,1.021 0.604,1.219 0.458,0.198 10 false A100 1.229,1.76 1.844,1.958 0.615,0.198 10 false CANH 1.229,0.25 1.844,0.448 0.615,0.198 10 false CANL 0.115,1.688 0.729,1.885 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-22 (CANH) - A100-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A100-22 (CANH) - A100-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-10 (CANL) - A100-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-22 (CANH) - A100-13 (BM) B - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A100-10 (CANL) - A100-13 (BM) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C228050E03
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 G12 2.833,0.896 3.24,1.052 0.406,0.156 10 ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 BAT

a.
C277459C04
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G12 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G12-3 (CANH) - G12-1 (ESS) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-2 (CANL) - G12-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-3 (CANH) - G12-5 (BAT) P - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G12-2 (CANL) - G12-5 (BAT) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


B264892E76
4.719,0.646 5.167,0.927 0.448,0.281 1.854,0.646 2.302,0.927 0.448,0.281 3.135,2.323 2.823,2.323 2.823,2.323 2.51,1.646 true 4.281,2.177 4.563,2.177 4.563,2.177 4.823,1.5 true 1.146,0.833 1.344,0.833 1.344,0.833 1.552,1.344 true 4.083,0.906 4.365,0.906 4.365,0.906 4.729,1.479 true 4.813,0.698 5.271,0.896 0.458,0.198 10 G84 3.646,0.823 4.104,1.021 0.458,0.198 10 CANL 3.833,2.094 4.292,2.292 0.458,0.198 10 CANH 0.938,0.771 1.396,0.969 0.458,0.198 10 +B 3.208,2.24 3.667,2.438 0.458,0.198 10 E 1.938,0.708 2.396,0.906 0.458,0.198 10 G82

a.
C277455C02
0.115,2.396 0.521,2.677 0.406,0.281 0.292,0.677 0.698,0.958 0.406,0.281 0.771,1.406 0.99,1.406 0.99,1.406 1.135,1.083 true 2.292,0.781 2.542,0.552 2.542,0.552 2.75,0.552 true 2.667,1.875 2.427,1.875 2.427,1.875 2.094,2.552 true 2.552,1.604 2.313,1.604 2.313,1.604 1.969,2.542 true 0.052,0.031 0.365,0.188 0.313,0.156 10 *a 0.354,0.74 0.667,0.896 0.313,0.156 10 G82 0.177,2.448 0.49,2.604 0.313,0.156 10 G84 0.615,1.323 0.927,1.479 0.313,0.156 10 E 2.802,0.469 3.115,0.625 0.313,0.156 10 +B 2.719,1.802 3.167,2.031 0.448,0.229 10 CANL 2.604,1.542 3.052,1.771 0.448,0.229 10 CANH
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G84-14 (CANH) - G84-15 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G84-14 (CANH) - G82-11 (E) R - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-15 (CANL) - G82-11 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-14 (CANH) - G82-2 (+B) R - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G84-15 (CANL) - G82-2 (+B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


C297912E01
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G141 4.979,0.146 5.594,0.344 0.615,0.198 10 false G143 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C07
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.51,0.302 1.969,0.5 0.458,0.198 10 false G141 1.542,1.885 2,2.083 0.458,0.198 10 false G143 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G143-9 (CANH) - G141-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-9 (CANH) - G141-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


C297912E08
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.49,0.177 2.104,0.375 0.615,0.198 10 false G137 4.99,0.146 5.604,0.344 0.615,0.198 10 false G139 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C27
1.479,0.26 1.917,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.531,0.292 1.99,0.49 0.458,0.198 10 false G137 1.573,1.875 2.031,2.073 0.458,0.198 10 false G139 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G139-9 (CANH) - G139-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G139-9 (CANH) - G137-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G139-10 (CANL) - G137-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G139-9 (CANH) - G137-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G139-10 (CANL) - G137-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD ECU ASSEMBLY (for 4WD/AWD)


C270073E03
3.385,0.135 3.813,0.438 0.427,0.302 4.667,1.531 5.146,2.646 5.146,2.646 5.385,2.646 true 4.865,1.531 5.344,2.396 5.344,2.396 5.552,2.396 true 1.677,0.313 1.906,0.313 1.906,0.313 2.427,1.156 true 3.469,0.208 3.938,0.375 0.469,0.167 10 G86 5.594,2.323 6.063,2.49 0.469,0.167 10 CANL 5.438,2.563 5.906,2.729 0.469,0.167 10 CANH 1.344,0.25 1.813,0.417 0.469,0.167 10 GND

a.
C251150C05
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 2.208,2.833 2.417,3.021 2.417,3.021 2.594,3.021 true 2.229,1.094 2.438,1.281 2.438,1.281 2.615,1.281 true 2.167,1.094 2.333,1.563 2.333,1.563 2.51,1.563 true 0.875,0.688 1.094,0.688 1.094,0.688 1.229,0.948 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2.083 0.417,2.24 0.313,0.156 10 *b 0.479,2.563 0.854,2.771 0.375,0.208 10 G14 2.656,2.938 3.031,3.146 0.375,0.208 10 BAT 2.563,1.49 3.042,1.76 0.479,0.271 10 CANH 2.667,1.198 3.146,1.469 0.479,0.271 10 CANL 0.51,0.99 0.885,1.198 0.375,0.208 10 G86 0.552,0.635 1.031,0.906 0.479,0.271 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G86-6 (CANH) - G86-4 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-5 (CANL) - G86-4 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-6 (CANH) - G14-16 (BAT) GR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G86-5 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)


C347359E02
1.469,0.542 1.948,0.781 0.479,0.24 4.969,0.531 5.448,0.771 0.479,0.24 0.615,2.125 0.76,2.125 0.76,2.125 1.26,1.594 true 2.677,2.125 2.51,2.125 2.51,2.125 2.24,1.573 true 6.302,2.083 6.135,2.083 6.135,2.083 5.865,1.531 true 5.115,2.125 5.26,2.125 5.26,2.125 5.771,1.531 true 1.594,0.552 2.052,0.75 0.458,0.198 10 false A86 5.063,0.563 5.521,0.76 0.458,0.198 10 false G87 2.719,2.01 3.177,2.208 0.458,0.198 10 false BIN1 0.188,2.01 0.646,2.208 0.458,0.198 10 false GND1 6.333,1.99 6.792,2.188 0.458,0.198 10 false CANH 4.708,2.021 5.167,2.219 0.458,0.198 10 false CANL

a.
C347360C02
0.146,2.427 0.563,2.635 0.417,0.208 0.365,0.781 0.781,0.99 0.417,0.208 0.677,1.5 0.833,1.5 0.833,1.5 1.125,1.177 true 0.49,3.052 0.646,3.052 0.646,3.052 0.938,2.729 true 0.802,3.26 0.958,3.26 0.958,3.26 1.042,2.708 true 2.656,1.583 2.469,1.583 2.469,1.583 2.24,1.219 true 0.125,0.146 0.438,0.302 0.313,0.156 10 false *a 0.438,0.792 0.75,0.948 0.313,0.156 10 false A86 0.229,2.438 0.542,2.594 0.313,0.156 10 false G87 0.333,1.396 0.792,1.604 0.458,0.208 10 false BIN1 2.708,1.479 3.167,1.688 0.458,0.208 10 false GND1 0.063,2.958 0.521,3.167 0.458,0.208 10 false CANH 0.396,3.167 0.854,3.375 0.458,0.208 10 false CANL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G87-13 (CANH) - G87-14 (CANL) LG - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G87-13 (CANH) - A86-8 (GND1) LG - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-14 (CANL) - A86-8 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-13 (CANH) - A86-3 (BIN1) LG - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G87-14 (CANL) - A86-3 (BIN1) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


C278749E01
3.375,0.25 3.854,0.542 0.479,0.292 2.417,0.25 2.75,0.25 2.75,0.25 3.375,1.417 true 2.167,0.5 2.5,0.5 2.5,0.5 3.25,1.406 true 4.365,1.521 5.063,2.417 5.063,2.417 5.417,2.417 true 2.083,2.417 2.417,2.417 2.417,2.417 3.083,1.406 true 3.49,0.333 3.948,0.531 0.458,0.198 10 G81 1.771,0.427 2.333,0.667 0.563,0.24 10 CANL 1.75,2.333 2.208,2.531 0.458,0.198 10 GND 2,0.177 2.563,0.417 0.563,0.24 10 CANH 5.479,2.333 5.938,2.531 0.458,0.198 10 B

a.
C240157C06
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.333,1.052 0.792,1.25 0.458,0.198 10 G81 2.333,0.406 2.792,0.604 0.458,0.198 10 CANH 2.25,0.156 2.708,0.354 0.458,0.198 10 CANL 3.031,1.531 3.333,1.802 0.302,0.271 10 B 0.667,0.385 1.031,0.646 0.365,0.26 10 GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G81-11 (CANH) - G81-12 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G81-11 (CANH) - G81-14 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-12 (CANL) - G81-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-11 (CANH) - G81-21 (B) B - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G81-12 (CANL) - G81-21 (B) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY


C239855E06
3.781,1.781 4.188,2.021 0.406,0.24 3.656,0.271 4.063,0.51 0.406,0.24 1.854,0.896 2.188,1.094 0.333,0.198 0.896,1.323 1.229,1.521 0.333,0.198 2.021,0.896 2.021,0.781 false 1.042,1.313 1.042,1.135 true 3.385,2.406 3.594,2.406 3.594,2.406 3.823,2.573 true 3.406,3.125 3.615,3.125 3.615,3.125 3.844,2.729 true 3.156,1.563 3.375,1.563 3.375,1.563 3.563,1.052 true 4.698,1.521 4.438,1.521 4.438,1.521 4.198,1.052 true 0.969,1.344 1.281,1.542 0.313,0.198 10 h1 1.938,0.917 2.25,1.115 0.313,0.198 10 h2 3.771,0.313 4.083,0.51 0.313,0.198 10 h2 3.917,1.833 4.229,2.031 0.313,0.198 10 h1 2.948,2.344 3.5,2.521 0.552,0.177 10 CANH 2.979,3.052 3.531,3.229 0.552,0.177 10 CANL 2.729,1.49 3.281,1.667 0.552,0.177 10 PGND 4.75,1.448 5.302,1.625 0.552,0.177 10 PIG

a.
C279366C01
0.354,2.479 0.719,2.74 0.365,0.26 0.458,0.969 0.823,1.229 0.365,0.26 1.969,0.938 2.25,0.74 2.25,0.74 2.469,0.74 true 1.969,1.25 2.208,1.521 2.208,1.521 2.427,1.521 true 2.156,2.615 2.438,2.417 2.438,2.417 2.656,2.417 true 0.844,2.271 1.094,2.271 1.094,2.271 1.323,2.542 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.563,1.01 0.875,1.167 0.313,0.156 10 h1 0.469,2.531 0.781,2.688 0.313,0.156 10 h2 2.521,0.646 3.01,0.854 0.49,0.208 10 CANH 2.469,1.427 2.958,1.635 0.49,0.208 10 CANL 2.708,2.333 3.198,2.542 0.49,0.208 10 PGND 0.573,2.188 1.063,2.396 0.49,0.208 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
h1-4 (CANH) - h2-2 (PGND) W - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-8 (CANL) - h2-2 (PGND) B - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-4 (CANH) - h2-1 (PIG) W - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h1-8 (CANL) - h2-1 (PIG) B - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


C270135E10
1.458,0.198 1.938,0.406 0.479,0.208 2.417,0.583 2.229,0.583 2.229,0.583 1.958,1.01 true 1.281,1.354 0.917,1.844 0.917,1.844 0.729,1.844 true 2.469,1.823 2.26,1.823 2.26,1.823 1.948,1.344 true 1.604,0.219 1.917,0.417 0.313,0.198 10 false R1 2.479,0.479 3.083,0.792 0.604,0.313 10 false CA1P 2.521,1.719 3.188,1.979 0.667,0.26 10 false CA1N 0.333,1.76 0.938,2.073 0.604,0.313 10 false BLGD

a.
C268298C15
1.5,1.958 1.979,2.188 0.479,0.229 1.469,0.24 1.885,0.5 0.417,0.26 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.563,1.219 1.24,1.542 1.24,1.542 1.073,1.542 true 1.563,1.063 1.219,0.646 1.219,0.646 0.99,0.646 true 1.927,1.198 2.135,1.604 2.135,1.604 2.385,1.604 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.104,1.979 0.417,2.135 0.313,0.156 10 false *b 0.646,1.438 1.26,1.646 0.615,0.208 10 false CA1N 2.573,3.156 3.063,3.354 0.49,0.198 10 false BAT 1.594,0.292 1.99,0.469 0.396,0.177 10 false R1 1.604,1.99 2,2.167 0.396,0.177 10 false G14 0.583,0.531 1.198,0.813 0.615,0.281 10 false CA1P 2.448,1.51 2.938,1.708 0.49,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R1-2 (CA1P) - R1-7 (CA1N) R - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R1-2 (CA1P) - R1-10 (BLGD) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-7 (CA1N) - R1-10 (BLGD) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-2 (CA1P) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-7 (CA1N) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


C323669E08
4.219,0.323 4.771,0.573 0.552,0.25 2.563,0.323 3.115,0.573 0.552,0.25 0.99,2.333 1.177,2.333 1.177,2.333 1.792,1.458 true 1.51,2.625 1.698,2.625 1.698,2.625 1.885,1.479 true 3.292,2.406 3.479,2.406 3.479,2.406 4.042,1.583 true 5.833,0.531 5.625,0.531 5.625,0.531 4.865,1.271 true 2.708,0.344 3.167,0.542 0.458,0.198 10 false U29 4.365,0.354 4.823,0.552 0.458,0.198 10 false U30 1.073,2.521 1.531,2.719 0.458,0.198 10 false CANP 0.573,2.219 1.031,2.417 0.458,0.198 10 false CANN 2.948,2.292 3.406,2.49 0.458,0.198 10 false GND 5.948,0.448 6.406,0.646 0.458,0.198 10 false B

a.
C325480C19
1.5,0.375 1.958,0.615 0.458,0.24 1.417,2.302 1.917,2.552 0.5,0.25 0.688,2.635 0.844,2.635 0.844,2.635 1.01,3.094 true 2.781,1.448 2.417,1.896 2.417,1.896 2.208,1.896 true 2.813,3.875 2.667,3.875 2.667,3.875 2.292,3.583 true 2.917,1.448 2.677,2.125 2.677,2.125 2.469,2.125 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.396 2.063,0.594 0.458,0.198 10 false U29 1.531,2.333 1.99,2.531 0.458,0.198 10 false U30 1.771,1.792 2.25,1.979 0.479,0.188 10 false CANP 2.865,3.76 3.26,3.979 0.396,0.219 10 false GND 0.49,2.563 0.885,2.781 0.396,0.219 10 false B 2.052,2.031 2.531,2.219 0.479,0.188 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U29-39 (CANP) - U29-40 (CANN) G - GR HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
U29-39 (CANP) - U30-10 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U29-40 (CANN) - U30-10 (GND) GR - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U29-39 (CANP) - U30-1 (B) G - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
U29-40 (CANN) - U30-1 (B) GR - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type])


C251659E06
3.406,0.25 3.885,0.51 0.479,0.26 1.479,0.521 1.677,0.521 1.677,0.521 2.094,0.896 true 1.75,0.281 1.948,0.281 1.948,0.281 2.219,0.906 true 2.969,1.573 3.167,1.573 3.167,1.573 3.51,1.167 true 3.479,0.281 4.094,0.479 0.615,0.198 10 false G166 1.531,0.177 2.146,0.375 0.615,0.198 10 false R1 1.281,0.417 1.896,0.615 0.615,0.198 10 false R2 2.823,1.458 3.438,1.656 0.615,0.198 10 false E

a.
C251149C12
2.688,0.823 3.104,1.073 0.417,0.25 0.458,2.521 0.875,2.771 0.417,0.25 1.031,0.927 0.854,0.802 0.854,0.802 0.76,0.802 true 1.688,1.021 1.385,1.5 1.385,1.5 1.292,1.5 true 2.188,2.844 2.292,3.063 2.292,3.063 2.385,3.063 true 1.104,0.927 0.938,0.542 0.938,0.542 0.844,0.542 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.115,2 0.427,2.156 0.313,0.156 10 false *b 0.552,0.708 1.01,0.875 0.458,0.167 10 false R2 2.74,0.854 3.198,1.021 0.458,0.167 10 false G166 0.542,2.542 1,2.708 0.458,0.167 10 false G14 2.438,2.948 2.896,3.115 0.458,0.167 10 false BAT 0.656,0.438 1.115,0.604 0.458,0.167 10 false R1 1.146,1.396 1.604,1.563 0.458,0.167 10 false E
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3


Disconnect the clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G166-17 (R1) - G166-18 (R2) R - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G166-17 (R1) - G166-30 (E) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G166-18 (R2) - G166-30 (E) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G166-17 (R1) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G166-18 (R2) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)


C279365C02
1.5,0.26 1.927,0.542 0.427,0.281 0.802,0.771 0.938,0.771 0.938,0.771 1.229,1.167 true 0.865,1.875 1.01,1.875 1.01,1.875 1.24,1.552 true 1.646,1.531 2,2.01 2,2.01 2.167,2.01 true 0.948,0.438 1.083,0.438 1.083,0.438 1.385,1.208 true 1.146,2.083 1.292,2.083 1.292,2.083 1.448,1.552 true 1.573,0.302 2.031,0.5 0.458,0.198 10 false Q17 0.219,0.688 0.854,0.896 0.635,0.208 10 false CANH*B 0.302,1.771 1,1.979 0.698,0.208 10 false CANL*B 2.229,1.906 2.688,2.104 0.458,0.198 10 false GND 0.292,0.344 0.927,0.552 0.635,0.208 10 false CA1P*A 0.594,1.979 1.156,2.146 0.563,0.167 10 false CA1N*A
*A Bus 5
*B Local Bus


a.
C267485C14
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 2.198,2.917 2.344,3.125 2.344,3.125 2.563,3.125 true 2.073,1.406 2.219,1.615 2.219,1.615 2.438,1.615 true 2.063,1.135 2.208,0.958 2.208,0.958 2.427,0.958 true 1.792,1.375 1.427,1.792 1.427,1.792 1.208,1.792 true 1.927,1.385 2.135,1.802 2.135,1.802 2.354,1.802 true 1.906,1.125 2.281,0.594 2.281,0.594 2.5,0.594 true 0.083,0.083 0.396,0.25 0.313,0.167 10 false *a 0.167,2.094 0.479,2.25 0.313,0.156 10 false *b 2.615,3.052 2.969,3.24 0.354,0.188 10 false BAT 0.49,2.583 0.844,2.771 0.354,0.188 10 false G14 0.635,1.094 0.99,1.281 0.354,0.188 10 false Q17 2.469,1.521 3.104,1.74 0.635,0.219 10 false CANL*B 0.865,1.698 1.333,1.885 0.469,0.188 10 false GND 2.542,0.5 3.229,0.771 0.688,0.271 10 false CA1P*A 2.385,1.688 3.146,1.927 0.76,0.24 10 false CA1N*A 2.469,0.865 3.104,1.083 0.635,0.219 10 false CANH*B
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q17-5 (CA1P) - Q17-11 (CA1N) G - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q17-5 (CA1P) - Q17-10 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q17-11 (CA1N) - Q17-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q17-5 (CA1P) - G14-16 (BAT) G - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q17-11 (CA1N) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q17-6 (CANH) - Q17-12 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
Q17-6 (CANH) - Q17-10 (GND) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q17-12 (CANL) - Q17-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q17-6 (CANH) - G14-16 (BAT) L - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q17-12 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


C334530C04
1.313,0.781 1.917,1.052 0.604,0.271 2.177,0.25 2.354,0.25 2.354,0.25 2.833,0.854 true 1.969,0.5 2.146,0.5 2.146,0.5 2.698,0.844 true 3.083,0.854 3.479,0.458 3.479,0.458 3.688,0.458 true 2.969,0.865 3.302,0.219 3.302,0.219 3.51,0.219 true 2.927,0.99 3.313,1.385 3.313,1.385 3.521,1.385 true 3.729,0.354 4.646,0.552 0.917,0.198 10 false CA1P*B 3.542,0.125 4.458,0.323 0.917,0.198 10 false CA1N*B 1.583,0.146 2.5,0.344 0.917,0.198 10 false CA2H*A 1.438,0.396 2.354,0.594 0.917,0.198 10 false CA2L*A 3.583,1.26 4.5,1.458 0.917,0.198 10 false GND 1.448,0.823 2.365,1.021 0.917,0.198 10 false G168
*A Bus 5 *B Local Bus


a.
C339054C02
0.198,0.292 0.719,0.51 0.521,0.219 0.24,2.479 0.729,2.677 0.49,0.198 2.646,3.052 2.49,3.052 2.49,3.052 2.25,2.781 true 2.813,1.708 2.625,1.708 2.625,1.708 2.281,1.156 true 2.833,0.51 2.646,0.51 2.646,0.51 2.542,0.958 true 2.698,0.292 2.51,0.292 2.51,0.292 2.427,0.958 true 2.167,0.958 1.833,0.406 1.833,0.406 1.635,0.406 true 2.292,0.948 2.01,0.156 2.01,0.156 1.813,0.156 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 0.083,1.833 0.396,1.99 0.313,0.156 10 false *b 0.375,2.5 0.688,2.656 0.313,0.156 10 false G14 0.271,0.313 0.688,0.521 0.417,0.208 10 false G168 2.75,0.188 3.333,0.375 0.583,0.188 10 false CA2H*A 2.896,0.417 3.427,0.615 0.531,0.198 10 false CA2L*A 2.865,1.625 3.396,1.823 0.531,0.198 10 false GND 2.698,2.958 3.229,3.156 0.531,0.198 10 false BAT 1.104,0.323 1.635,0.521 0.531,0.198 10 false CA1P*B 1.25,0.052 1.781,0.25 0.531,0.198 10 false CA1N*B
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3


Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G168-10 (CA2H) - G168-11 (CA2L) P - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G168-10 (CA2H) - G168-28 (GND) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G168-11 (CA2L) - G168-28 (GND) LG - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G168-10 (CA2H) - G14-16 (BAT) P - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G168-11 (CA2L) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G168-8 (CA1P) - G168-9 (CA1N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G168-8 (CA1P) - G168-28 (GND) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G168-9 (CA1N) - G168-28 (GND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G168-8 (CA1P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G168-9 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


E321782C05
2.135,0.74 2.604,1.031 0.469,0.292 2.604,0.323 2.833,0.323 2.833,0.323 3.448,0.781 true 3.677,0.833 4.125,0.271 4.125,0.271 4.302,0.271 true 3.875,1.042 4.385,1.302 4.385,1.302 4.563,1.302 true 3.667,1.073 4.26,1.563 4.26,1.563 4.438,1.563 true 3.865,0.813 4.354,0.625 4.354,0.625 4.531,0.625 true 2.271,0.792 2.729,0.99 0.458,0.198 10 false Z6 2.083,0.219 2.656,0.406 0.573,0.188 10 false CA2H*A 4.344,0.156 4.875,0.333 0.531,0.177 10 false CA2L*A 4.604,1.188 5.177,1.375 0.573,0.188 10 false CA1P*B 4.51,1.448 5.083,1.635 0.573,0.188 10 false CA1N*B 4.583,0.531 5.156,0.719 0.573,0.188 10 false SGND
*A Bus 5 *B Local Bus


a.
C339037C03
0.25,2.396 0.719,2.646 0.469,0.25 2.51,0.625 2.979,0.875 0.469,0.25 0.896,1.396 1.052,1.396 1.052,1.396 1.469,1.01 true 1.208,1.688 1.365,1.688 1.365,1.688 1.635,1.021 true 2.313,2.771 2.573,3.021 2.573,3.021 2.75,3.021 true 0.792,0.635 0.948,0.635 0.948,0.635 1.458,0.865 true 1.052,0.365 1.208,0.365 1.208,0.365 1.625,0.844 true 1.323,0.156 1.479,0.156 1.479,0.156 1.75,0.854 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.115,1.833 0.427,1.99 0.313,0.156 10 false *b 0.354,2.417 0.667,2.573 0.313,0.156 10 false G14 2.656,0.635 2.969,0.792 0.313,0.156 10 false Z6 0.354,1.271 0.948,1.448 0.594,0.177 10 false CA1P*B 0.667,1.552 1.271,1.74 0.604,0.188 10 false CA1N*B 2.802,2.885 3.24,3.063 0.438,0.177 10 false BAT 0.375,0.531 0.969,0.708 0.594,0.177 10 false SGND 0.5,0.271 1.094,0.448 0.594,0.177 10 false CA2L*A 0.75,0.052 1.344,0.229 0.594,0.177 10 false CA2H*A
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Z6-3 (CA2H) - Z6-2 (CA2L) B - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Z6-3 (CA2H) - Z6-1 (SGND) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z6-2 (CA2L) - Z6-1 (SGND) LG - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z6-3 (CA2H) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Z6-2 (CA2L) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Z6-5 (CA1P) - Z6-6 (CA1N) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
Z6-5 (CA1P) - Z6-1 (SGND) SB - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z6-6 (CA1N) - Z6-1 (SGND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z6-5 (CA1P) - G14-16 (BAT) SB - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Z6-6 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System [for Camera built-in ECU])


E286120E22
3.385,0.094 3.833,0.302 0.448,0.208 4.323,1.531 4.188,1.531 4.188,1.531 3.833,1.198 true 4.323,0.594 4.188,0.594 4.188,0.594 3.854,0.885 true 3.531,0.125 3.885,0.313 0.354,0.188 10 false c2 4.396,1.427 5.01,1.625 0.615,0.198 10 false CANH 4.385,0.51 5,0.708 0.615,0.198 10 false CANL

a.
C311029C04
1.438,0.115 2,0.344 0.563,0.229 0.302,2.531 0.771,2.844 0.469,0.313 0.781,0.427 0.948,0.427 0.948,0.427 1.448,0.969 true 0.885,1.729 1.052,1.729 1.052,1.729 1.479,1.292 true 2.615,3.188 2.49,3.188 2.49,3.188 2.24,2.865 true 1.208,2.073 1.375,2.073 1.375,2.073 1.677,2.448 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.021 0.458,2.177 0.313,0.156 10 false *b 0.427,1.635 1.042,1.833 0.615,0.198 10 false CANH 0.396,0.323 1.01,0.521 0.615,0.198 10 false CANL 1.625,0.135 2.24,0.333 0.615,0.198 10 false c2 0.417,2.583 1.031,2.781 0.615,0.198 10 false G14 0.969,1.979 1.583,2.177 0.615,0.198 10 false CG 2.688,3.073 3.302,3.271 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Television Camera Assembly)
*b Front view of DLC3


Disconnect the television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c2-4 (CANH) - c2-1 (CANL) P - G HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
c2-4 (CANH) - G14-4 (CG) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
c2-1 (CANL) - G14-4 (CG) G - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
c2-4 (CANH) - G14-16 (BAT) P - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
c2-1 (CANL) - G14-16 (BAT) G - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Memory)


B219506E58
4.74,0.833 5.115,1.063 0.375,0.229 1.938,0.958 2.313,1.188 0.375,0.229 5.042,1.427 4.844,1.427 4.844,1.427 4.427,1.219 true 4.927,1.625 4.729,1.625 4.729,1.625 4.354,1.208 true 3.708,0.531 3.458,0.531 3.458,0.531 3.552,0.917 true 3.469,0.208 3.271,0.208 3.271,0.208 3.531,1.115 true 4.844,0.865 5.156,1.063 0.313,0.198 10 false d28 2,1 2.313,1.198 0.313,0.198 10 false d27 4.969,1.521 5.583,1.719 0.615,0.198 10 false CANP 5.083,1.323 5.698,1.521 0.615,0.198 10 false CANN 3.76,0.427 4.375,0.625 0.615,0.198 10 false GND1 3.51,0.125 4.125,0.323 0.615,0.198 10 false +B1

a.
C219234C21
0.208,1.208 0.625,1.479 0.417,0.271 2.74,0.948 3.135,1.208 0.396,0.26 2.802,1.656 2.667,1.656 2.667,1.656 2.542,1.573 true 2.656,1.917 2.521,1.917 2.521,1.917 2.438,1.563 true 1.375,1.25 0.99,0.823 0.99,0.823 0.781,0.823 true 0.885,1.833 1.052,1.833 1.052,1.833 1.375,1.396 true 0.104,0.073 0.594,0.49 0.49,0.417 10 false *a 0.302,1.271 0.677,1.521 0.375,0.25 10 false d27 2.844,0.99 3.177,1.208 0.333,0.219 10 false d28 2.854,1.573 3.292,1.771 0.438,0.198 10 false CANN 2.708,1.833 3.188,2.021 0.479,0.188 10 false CANP 0.594,1.74 1.031,1.938 0.438,0.198 10 false +B1 0.375,0.74 0.813,0.938 0.438,0.198 10 false GND1
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)


Disconnect the position control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d28-8 (CANP) - d28-7 (CANN) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
d28-8 (CANP) - d27-2 (GND1) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
d28-7 (CANN) - d27-2 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
d28-8 (CANP) - d27-7 (+B1) L - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d28-7 (CANN) - d27-7 (+B1) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher