Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221951 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Short to B+ in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Detection Item Trouble Area

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: for 4WD/AWD

*3: w/ Stop and Start System

*4: w/ Telematics Transceiver

The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

ECM

·

Combination meter assembly

·

Power steering ECU assembly

·

Air conditioning amplifier assembly

·

Airbag sensor assembly

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Radio and display receiver assembly*1

·

4WD ECU assembly*2

·

Brake actuator assembly (skid control ECU)

·

Main body ECU (multiplex network body ECU)

·

Engine stop and start ECU*3

·

Telematics transceiver*4

·

No. 6 CAN junction connector

·

No. 7 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C347971E02
4.073,0.781 4.385,0.979 0.313,0.198 10 false 15 4.083,0.26 4.396,0.458 0.313,0.198 10 false 5 3.25,0.26 3.563,0.458 0.313,0.198 10 false 1 3.167,0.781 3.479,0.979 0.313,0.198 10 false 11 3.135,2.74 3.448,2.938 0.313,0.198 10 false 13 4.104,4.688 4.417,4.885 0.313,0.198 10 false 19 4.115,2.719 4.427,2.917 0.313,0.198 10 false 12 3.156,6.656 3.469,6.854 0.313,0.198 10 false 18 3.219,2.188 3.531,2.385 0.313,0.198 10 false 3 3.208,6.115 3.521,6.313 0.313,0.198 10 false 8 4.156,4.167 4.469,4.365 0.313,0.198 10 false 9 4.146,2.177 4.458,2.375 0.313,0.198 10 false 2 3.135,4.177 3.448,4.375 0.313,0.198 10 false 10 3.135,4.698 3.448,4.896 0.313,0.198 10 false 20 4.115,6.104 4.427,6.302 0.313,0.198 10 false 4 4.094,6.646 4.406,6.844 0.313,0.198 10 false 14 6.198,1.385 6.656,1.583 0.458,0.198 10 false ECM 4.5,0.375 4.948,0.573 0.448,0.198 10 false A62 4.49,0.906 4.938,1.104 0.448,0.198 10 false A62 5.01,0.385 5.458,0.583 0.448,0.198 10 false A62 5.01,0.917 5.458,1.115 0.448,0.198 10 false A62 5.521,0.385 5.969,0.583 0.448,0.198 10 false A61 5.521,0.906 5.969,1.104 0.448,0.198 10 false A61 4.479,0.146 5.094,0.344 0.615,0.198 10 false 13*1 4.979,0.146 5.594,0.344 0.615,0.198 10 false 26*2 5.552,0.146 6.167,0.344 0.615,0.198 10 false 7*3 4.458,0.667 5.073,0.865 0.615,0.198 10 false 26*1 4.979,0.667 5.594,0.865 0.615,0.198 10 false 25*2 5.552,0.677 6.167,0.875 0.615,0.198 10 false 6*3 6.021,0.281 6.635,0.479 0.615,0.198 10 false CANH 6.052,1.063 6.667,1.26 0.615,0.198 10 false CANL 0.875,0.406 1.49,0.604 0.615,0.198 10 false CANH 0.906,0.938 1.521,1.135 0.615,0.198 10 false CANL 1.396,0.25 1.708,0.448 0.313,0.198 10 false 14 1.406,0.792 1.719,0.99 0.313,0.198 10 false 13 0.094,1.188 0.542,1.385 0.448,0.198 10 false G78 0.104,1.365 3.219,1.656 3.115,0.292 10 false Main Body ECU (Multiplex Network Body ECU) 5.156,3.302 7.156,3.573 2,0.271 10 false Power Steering ECU Assembly 5.156,3.135 5.604,3.333 0.448,0.198 10 false h1 5.99,2.354 6.604,2.552 0.615,0.198 10 false CANH 6.01,2.885 6.625,3.083 0.615,0.198 10 false CANL 5.708,2.208 6.021,2.406 0.313,0.198 10 false 4 5.698,2.75 6.01,2.948 0.313,0.198 10 false 8 1.438,2.198 1.75,2.396 0.313,0.198 10 false 22 1.448,2.719 1.76,2.917 0.313,0.198 10 false 10 0.854,2.333 1.469,2.531 0.615,0.198 10 false CANH 0.875,2.865 1.49,3.063 0.615,0.198 10 false CANL 0.063,3.281 3.177,3.573 3.115,0.292 10 false Brake Actuator Assembly (Skid Control ECU) 0.052,3.115 0.5,3.313 0.448,0.198 10 false A100 5.51,5.271 7.115,5.573 1.604,0.302 10 false Airbag Sensor Assembly 5.5,5.094 5.948,5.292 0.448,0.198 10 false G92 5.979,4.313 6.594,4.51 0.615,0.198 10 false CANH 6.01,4.844 6.625,5.042 0.615,0.198 10 false CANL 5.677,4.146 5.99,4.344 0.313,0.198 10 false 13 5.677,4.688 5.99,4.885 0.313,0.198 10 false 22 0.885,4.302 1.5,4.5 0.615,0.198 10 false CANH 0.917,4.823 1.531,5.021 0.615,0.198 10 false CANL 1.469,4.156 1.781,4.354 0.313,0.198 10 false 8 1.49,4.656 1.802,4.854 0.313,0.198 10 false 9 0.104,5.24 2.521,5.531 2.417,0.292 10 false Air Conditioning Amplifier Assembly 0.104,5.083 0.552,5.281 0.448,0.198 10 false G80 1.479,6.635 1.792,6.833 0.313,0.198 10 false 14 1.51,6.115 1.823,6.313 0.313,0.198 10 false 6 0.729,7.396 1.24,7.635 0.51,0.24 10 false DLC3 0.75,7.208 1.198,7.406 0.448,0.198 10 false G14 0.844,6.26 1.458,6.458 0.615,0.198 10 false CANH 0.865,6.781 1.479,6.979 0.615,0.198 10 false CANL 2.729,7.188 4.823,7.417 2.094,0.229 10 false No. 6 CAN Junction Connector 2.719,7.021 3.167,7.219 0.448,0.198 10 false G171 0.198,7.979 2.656,8.198 2.458,0.219 10 false *1: for 2AR-FE, 3ZR-FAE, 3ZR-FE 0.219,8.385 2.677,8.604 2.458,0.219 10 false *2: for 2WW 2.583,7.969 5.99,8.188 3.406,0.219 10 false *3: for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF

C348129E02
4.552,3.594 7.156,3.802 2.604,0.208 10 false Radio and Display Receiver Assembly*1 4.552,3.458 5.146,3.615 0.594,0.156 10 false G143 6.021,2.656 6.615,2.813 0.594,0.156 10 false CANH 6.01,3.177 6.604,3.333 0.594,0.156 10 false CANL 5.74,2.563 6.333,2.719 0.594,0.156 10 false 9 5.667,3.073 6.26,3.229 0.594,0.156 10 false 10 4.115,2.531 4.708,2.688 0.594,0.156 10 false 3 4.104,3.052 4.698,3.208 0.594,0.156 10 false 13 4.073,0.594 4.667,0.75 0.594,0.156 10 false 8 4.073,1.125 4.667,1.281 0.594,0.156 10 false 18 3.198,2.531 3.792,2.688 0.594,0.156 10 false 4 3.177,3.042 3.771,3.198 0.594,0.156 10 false 14 0.094,3.604 2.698,3.813 2.604,0.208 10 false Engine Stop and Start ECU*3 0.094,3.458 2.698,3.667 2.604,0.208 10 false G87 1.417,2.542 2.01,2.698 0.594,0.156 10 false 13 1.427,3.063 2.021,3.219 0.594,0.156 10 false 14 0.854,2.667 1.448,2.823 0.594,0.156 10 false CANH 0.906,3.177 1.5,3.333 0.594,0.156 10 false CANL 4.115,4.469 4.708,4.625 0.594,0.156 10 false 6 4.083,5 4.677,5.156 0.594,0.156 10 false 16 6.01,4.615 6.604,4.771 0.594,0.156 10 false CANH 6.01,5.135 6.604,5.292 0.594,0.156 10 false CANL 5.573,5.542 7.156,5.781 1.583,0.24 10 false G86 5.573,5.729 7.156,5.969 1.583,0.24 10 false 4WD ECU Assembly*2 5.74,4.458 6.333,4.615 0.594,0.156 10 false 6 5.729,5.021 6.323,5.177 0.594,0.156 10 false 5 3.198,4.479 3.792,4.635 0.594,0.156 10 false 9 3.167,5.021 3.76,5.177 0.594,0.156 10 false 19 1.479,4.469 2.073,4.625 0.594,0.156 10 false 3 1.49,4.969 2.083,5.125 0.594,0.156 10 false 2 0.854,4.615 1.448,4.771 0.594,0.156 10 false CANH 0.896,5.156 1.49,5.313 0.594,0.156 10 false CANL 0.021,5.542 2.458,6 2.438,0.458 10 false G12 0.021,5.74 2.458,6.198 2.438,0.458 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 4.094,6.5 4.688,6.656 0.594,0.156 10 false 1 4.115,7.01 4.708,7.167 0.594,0.156 10 false 11 5.25,7.667 7.115,7.896 1.865,0.229 10 false Combination Meter Assembly 5.24,7.521 7.104,7.75 1.865,0.229 10 false G16 5.677,6.521 6.271,6.677 0.594,0.156 10 false 32 5.677,7.031 6.271,7.188 0.594,0.156 10 false 31 6.021,6.51 6.615,6.667 0.594,0.156 10 false CANH 6.073,7.323 6.667,7.479 0.594,0.156 10 false CANL 2.844,7.583 4.771,7.771 1.927,0.188 10 false No. 7 CAN Junction Connector 2.833,7.427 4.76,7.615 1.927,0.188 10 false G172 3.229,0.583 3.823,0.74 0.594,0.156 10 false 2 3.167,1.125 3.76,1.281 0.594,0.156 10 false 12 0.865,0.74 1.458,0.896 0.594,0.156 10 false CANP 0.875,1.271 1.469,1.427 0.594,0.156 10 false CANN 1.417,1.125 2.01,1.281 0.594,0.156 10 false 16 1.417,0.594 2.01,0.75 0.594,0.156 10 false 15 0.063,1.521 2.667,1.729 2.604,0.208 10 false M38 0.063,1.719 2.667,1.927 2.604,0.208 10 false Telematics Transceiver*4 0.083,6.771 2.281,7.125 2.198,0.354 10 false *1: w/ Audio and Visual System (for Radio and Display Type) 0.094,7.531 2.167,7.729 2.073,0.198 10 false *2: for 4WD/AWD 0.094,7.938 2.167,8.135 2.073,0.198 10 false *3: w/ Stop and Start System 0.083,8.292 2.156,8.49 2.073,0.198 10 false *4: w/ Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C280369C30
3.125,1.385 3.646,1.698 0.521,0.313 5.302,0.781 5.719,1.052 0.417,0.271 1.01,1.458 0.917,1.344 0.917,1.344 0.781,1.344 true 1.229,1.469 0.969,1.125 0.969,1.125 0.833,1.125 true 1.594,1.448 1.104,0.615 1.104,0.615 0.969,0.615 true 1.75,1.479 1.323,0.406 1.323,0.406 1.188,0.406 true 1.031,1.625 0.958,1.729 0.958,1.729 0.823,1.729 true 1.25,1.604 1.063,1.927 1.063,1.927 0.927,1.927 true 1.604,1.646 1.271,2.375 1.271,2.375 1.083,2.375 true 1.792,1.635 1.438,2.594 1.438,2.594 1.177,2.594 true 6.292,1.854 6.115,1.854 6.115,1.854 5.938,1.635 true 3.302,2.49 3.125,2.49 3.125,2.49 2.74,1.625 true 3.365,0.344 3.146,0.344 3.146,0.344 2.729,1.448 true 1.396,1.635 1.115,2.177 1.115,2.177 0.979,2.177 true 1.406,1.479 1.01,0.844 1.01,0.844 0.875,0.844 true 3.531,0.635 3.313,0.635 3.313,0.635 2.917,1.448 true 3.469,2.313 3.292,2.313 3.292,2.313 2.885,1.625 true 3.24,0.146 3.021,0.146 3.021,0.146 2.531,1.438 true 3.198,2.698 3.021,2.698 3.021,2.698 2.542,1.625 true 0.104,0.167 0.75,0.323 0.646,0.156 10 false *a 4.271,0.25 4.583,0.406 0.313,0.156 10 false *b 0.24,1.281 0.813,1.552 0.573,0.271 10 false CANH*c 0.292,1.083 0.875,1.365 0.583,0.281 10 false CANH*d 0.448,0.563 1.031,0.781 0.583,0.219 10 false CANH*f 0.677,0.333 1.26,0.563 0.583,0.229 10 false CANH*g 3.531,2.25 4.094,2.458 0.563,0.208 10 false CANL*j 3.208,1.458 3.615,1.667 0.406,0.208 10 false G171 5.375,0.833 5.708,1.021 0.333,0.188 10 false G14 6.333,1.792 6.646,1.948 0.313,0.156 10 false BAT 3.281,0.083 3.844,0.24 0.563,0.156 10 false CANH*h 0.667,2.51 1.354,2.667 0.688,0.156 10 false CANL*g 0.292,1.656 0.938,1.813 0.646,0.156 10 false CANL*c 0.406,1.875 0.99,2.156 0.583,0.281 10 false CANL*d 0.479,2.104 1.063,2.396 0.583,0.292 10 false CANL*e 0.583,2.323 1.167,2.542 0.583,0.219 10 false CANL*f 0.333,0.792 0.917,1.083 0.583,0.292 10 false CANH*e 3.406,0.271 3.969,0.448 0.563,0.177 10 false CANH*i 3.365,2.417 3.948,2.594 0.583,0.177 10 false CANL*i 3.271,2.625 3.833,2.781 0.563,0.156 10 false CANL*h 3.594,0.552 4.198,0.802 0.604,0.25 10 false CANH*j
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3
*c to Main Body ECU (Multiplex Network Body ECU) *d to Power Steering ECU Assembly
*e to Brake Actuator Assembly (Skid Control ECU) *f to No. 7 CAN Junction Connector
*g to ECM *h to DLC3
*i to Airbag Sensor Assembly *j to Air Conditioning Amplifier Assembly



b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
G171-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
G171-11 (CANL) - G14-16 (BAT)
G171-2 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power steering ECU assembly
G171-12 (CANL) - G14-16 (BAT)
G171-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly (skid control ECU)
G171-13 (CANL) - G14-16 (BAT)
G171-4 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 7 CAN junction connector
G171-14 (CANL) - G14-16 (BAT)
G171-5 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
G171-15 (CANL) - G14-16 (BAT)
G171-8 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher DLC3
G171-18 (CANL) - G14-16 (BAT)
G171-9 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag sensor assembly
G171-19 (CANL) - G14-16 (BAT)
G171-10 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
G171-20 (CANL) - G14-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 7 CAN junction connector CAN main wire) B
NG (DLC3 CAN branch wires) C
NG (ECU or sensor CAN main or branch wires) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

D

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G171 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

C280369C53
3.125,1.385 3.646,1.698 0.521,0.313 5.302,0.781 5.719,1.052 0.417,0.271 1.594,1.469 1.281,0.458 1.281,0.458 1.146,0.458 true 1.625,1.615 1.25,2.542 1.25,2.542 1.063,2.542 true 6.292,1.854 6.115,1.854 6.115,1.854 5.938,1.635 true 2.698,2.688 2.521,2.688 2.521,2.688 2.156,1.635 true 2.865,0.208 2.646,0.208 2.646,0.208 2.156,1.458 true 3.167,2 2.99,2 2.99,2 2.74,1.625 true 3.135,0.708 2.917,0.708 2.917,0.708 2.542,1.448 true 3.26,0.979 3.042,0.979 3.042,0.979 2.74,1.479 true 3.021,2.219 2.844,2.219 2.844,2.219 2.521,1.635 true 1.042,1.625 0.896,1.917 0.896,1.917 0.708,1.917 true 1.021,1.458 0.823,1.167 0.823,1.167 0.688,1.167 true 1.427,1.479 1.063,0.708 1.063,0.708 0.927,0.708 true 1.417,1.615 1.094,2.354 1.094,2.354 0.906,2.354 true 1.208,1.469 0.969,0.917 0.969,0.917 0.833,0.917 true 1.26,1.615 1.042,2.167 1.042,2.167 0.854,2.167 true 0.104,0.167 0.75,0.323 0.646,0.156 10 false *a 4.271,0.25 4.583,0.406 0.313,0.156 10 false *b 0.125,1.073 0.708,1.302 0.583,0.229 10 false CANH*c 0.635,0.375 1.219,0.594 0.583,0.219 10 false CANH*f 2.938,0.146 3.521,0.375 0.583,0.229 10 false CANH*g 3.073,2.146 3.698,2.354 0.625,0.208 10 false CANL*h 3.208,1.458 3.615,1.667 0.406,0.208 10 false G172 5.375,0.833 5.708,1.021 0.333,0.188 10 false G14 6.333,1.792 6.646,1.948 0.313,0.156 10 false BAT 3.188,0.635 3.75,0.792 0.563,0.156 10 false CANH*h 2.75,2.594 3.448,2.792 0.698,0.198 10 false CANL*g 0.167,1.823 0.698,2.063 0.531,0.24 10 false CANL*c 0.396,2.26 1.042,2.427 0.646,0.167 10 false CANL*e 0.563,2.469 1.146,2.656 0.583,0.188 10 false CANL*f 0.385,0.615 0.979,0.854 0.594,0.24 10 false CANH*e 0.26,0.844 0.854,1.042 0.594,0.198 10 false CANH*d 0.313,2.083 0.875,2.302 0.563,0.219 10 false CANL*d 3.219,1.927 3.844,2.135 0.625,0.208 10 false CANL*i 3.313,0.906 3.875,1.063 0.563,0.156 10 false CANH*i
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Combination Meter Assembly *d to Telematics Transceiver (w/ Telematics Transceiver)
*e to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) *f to Engine Stop and Start ECU (w/ Stop and Start System)
*g to 4WD ECU Assembly (for 4WD/AWD) *h to No. 6 CAN Junction Connector
*i to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: for 4WD/AWD

*3: w/ Stop and Start System

*4: w/ Telematics Transceiver

G172-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
G172-11 (CANL) - G14-16 (BAT)
G172-2 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Telematics transceiver*4
G172-12 (CANL) - G14-16 (BAT)
G172-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Radio and display receiver assembly*1
G172-13 (CANL) - G14-16 (BAT)
G172-4 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Engine stop and start ECU*3
G172-14 (CANL) - G14-16 (BAT)
G172-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher 4WD ECU assembly*2
G172-16 (CANL) - G14-16 (BAT)
G172-8 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 6 CAN junction connector
G172-18 (CANL) - G14-16 (BAT)
G172-9 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Spiral with sensor cable sub-assembly (steering angle sensor)
G172-19 (CANL) - G14-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (ECU or sensor CAN main or branch wires) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.
C253362C02
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 2.833,1.833 2.583,1.833 2.583,1.833 2.323,1.458 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 2.885,1.75 3.219,2 0.333,0.25 10 BAT
*a Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR