There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Detection Item | Trouble Area |
|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type) *2: for 4WD/AWD *3: w/ Stop and Start System *4: w/ Telematics Transceiver |
|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
Combination meter assembly ·
Power steering ECU assembly ·
Air conditioning amplifier assembly ·
Airbag sensor assembly ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Radio and display receiver assembly*1 ·
4WD ECU assembly*2 ·
Brake actuator assembly (skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
Engine stop and start ECU*3 ·
Telematics transceiver*4 ·
No. 6 CAN junction connector ·
No. 7 CAN junction connector ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to Power Steering ECU Assembly |
| *e | to Brake Actuator Assembly (Skid Control ECU) | *f | to No. 7 CAN Junction Connector |
| *g | to ECM | *h | to DLC3 |
| *i | to Airbag Sensor Assembly | *j | to Air Conditioning Amplifier Assembly |
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| G171-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| G171-11 (CANL) - G14-4 (CG) | |||
| G171-2 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| G171-12 (CANL) - G14-4 (CG) | |||
| G171-3 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| G171-13 (CANL) - G14-4 (CG) | |||
| G171-4 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 7 CAN junction connector |
| G171-14 (CANL) - G14-4 (CG) | |||
| G171-5 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ECM |
| G171-15 (CANL) - G14-4 (CG) | |||
| G171-8 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| G171-18 (CANL) - G14-4 (CG) | |||
| G171-9 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| G171-19 (CANL) - G14-4 (CG) | |||
| G171-10 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| G171-20 (CANL) - G14-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 7 CAN junction connector CAN main wire) | B |
| NG (DLC3 CAN branch wires) | C |
| NG (ECU or sensor CAN main or branch wires) | D |
A
B
C
D
Reconnect the G171 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 7 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Combination Meter Assembly | *d | to Telematics Transceiver (w/ Telematics Transceiver) |
| *e | to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) | *f | to Engine Stop and Start ECU (w/ Stop and Start System) |
| *g | to 4WD ECU Assembly (for 4WD/AWD) | *h | to No. 6 CAN Junction Connector |
| *i | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type) *2: for 4WD/AWD *3: w/ Stop and Start System *4: w/ Telematics Transceiver |
|||
| G172-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Combination meter assembly |
| G172-11 (CANL) - G14-4 (CG) | |||
| G172-2 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Telematics transceiver*4 |
| G172-12 (CANL) - G14-4 (CG) | |||
| G172-3 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Radio and display receiver assembly*1 |
| G172-13 (CANL) - G14-4 (CG) | |||
| G172-4 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Engine stop and start ECU*3 |
| G172-14 (CANL) - G14-4 (CG) | |||
| G172-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU assembly*2 |
| G172-16 (CANL) - G14-4 (CG) | |||
| G172-8 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 6 CAN junction connector |
| G172-18 (CANL) - G14-4 (CG) | |||
| G172-9 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| G172-19 (CANL) - G14-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 6 CAN junction connector CAN main wire) | B |
| NG (ECU or sensor CAN main or branch wires) | C |
A
B
C
| *a | Front view of DLC3 |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G14-14 (CANL) - G14-4 (CG) |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG