Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Speaker Circuit  


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.

If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E350599E03
0.354,2.198 1.656,2.563 1.302,0.365 10 false Front No. 1 Speaker Assembly RH 0.333,4.615 1.635,4.979 1.302,0.365 10 false Front No. 1 Speaker Assembly LH 0.75,6.135 1.667,6.5 0.917,0.365 10 false Rear Speaker Assembly RH 0.75,7.281 1.667,7.646 0.917,0.365 10 false Rear Speaker Assembly LH 2.917,3.177 5.177,3.396 2.26,0.219 10 false Telematics Transceiver*2 2.917,2.979 3.531,3.177 0.615,0.198 10 false M38 5.417,8.083 7.083,8.281 1.667,0.198 10 false Radio Receiver Assembly 3.521,0.917 3.833,1.115 0.313,0.198 10 false *1 3.646,3.563 3.958,3.76 0.313,0.198 10 false *1 2.667,2.802 2.979,3 0.313,0.198 10 false *2 1.75,4.375 1.906,4.573 0.156,0.198 10 false 1 1.74,2.677 1.896,2.875 0.156,0.198 10 false 2 4.531,1.719 4.844,1.917 0.313,0.198 10 false *2 2.604,1.708 2.917,1.906 0.313,0.198 10 false *2 4.479,2.823 4.792,3.021 0.313,0.198 10 false *2 2.979,1.688 3.135,1.885 0.156,0.198 10 false 5 2.958,2.552 3.115,2.75 0.156,0.198 10 false 6 4.208,2.573 4.365,2.771 0.156,0.198 10 false 3 4.229,1.708 4.385,1.906 0.156,0.198 10 false 2 3.76,1.792 4.208,1.99 0.448,0.198 10 false SPI+ 3.813,2.646 4.26,2.844 0.448,0.198 10 false SPI- 3.208,1.823 3.656,2.021 0.448,0.198 10 false SPO+ 3.208,2.667 3.656,2.865 0.448,0.198 10 false SPO- 1.729,1.896 1.885,2.094 0.156,0.198 10 false 1 1.76,5.052 1.917,5.25 0.156,0.198 10 false 2 1.76,7.667 1.917,7.865 0.156,0.198 10 false 2 1.76,6.51 1.917,6.708 0.156,0.198 10 false 2 1.76,5.906 1.917,6.104 0.156,0.198 10 false 1 1.76,7.063 1.917,7.26 0.156,0.198 10 false 1 5.417,1.813 5.875,2.01 0.458,0.198 10 false G46 5.406,2.698 5.865,2.896 0.458,0.198 10 false G46 5.406,4.271 5.865,4.469 0.458,0.198 10 false G46 5.406,5.146 5.865,5.344 0.458,0.198 10 false G46 5.406,5.896 5.865,6.094 0.458,0.198 10 false G47 5.406,6.531 5.865,6.729 0.458,0.198 10 false G47 5.406,7.052 5.865,7.25 0.458,0.198 10 false G47 5.406,7.688 5.865,7.885 0.458,0.198 10 false G47 5.823,1.813 6.281,2.01 0.458,0.198 10 false FR+ 5.823,2.708 6.281,2.906 0.458,0.198 10 false FR- 5.833,4.281 6.292,4.479 0.458,0.198 10 false FL+ 5.833,5.146 6.292,5.344 0.458,0.198 10 false FL- 5.833,5.896 6.292,6.094 0.458,0.198 10 false RR+ 5.833,7.052 6.292,7.25 0.458,0.198 10 false RL+ 5.833,7.677 6.292,7.875 0.458,0.198 10 false RL- 5.833,6.531 6.292,6.729 0.458,0.198 10 false RR- 5.479,1.604 5.635,1.802 0.156,0.198 10 false 1 5.521,2.469 5.677,2.667 0.156,0.198 10 false 5 5.5,4.052 5.656,4.25 0.156,0.198 10 false 2 5.51,4.927 5.667,5.125 0.156,0.198 10 false 6 5.5,5.677 5.656,5.875 0.156,0.198 10 false 1 5.51,6.313 5.667,6.51 0.156,0.198 10 false 3 5.51,6.823 5.667,7.021 0.156,0.198 10 false 2 5.5,7.458 5.656,7.656 0.156,0.198 10 false 6 0.25,8.167 2.333,8.365 2.083,0.198 10 false *1: w/o Telematics Transceiver 0.25,8.469 2.333,8.667 2.083,0.198 10 false *2: w/ Telematics Transceiver 0.365,1.948 0.677,2.146 0.313,0.198 10 false I1 0.344,4.427 0.656,4.625 0.313,0.198 10 false J1 0.75,5.948 1.063,6.146 0.313,0.198 10 false K2 0.75,7.094 1.063,7.292 0.313,0.198 10 false L2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>PRECAUTION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B



A

2.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

*1: for LH Side

*2: for RH Side


a.

Disconnect the G46 and G47 radio receiver assembly connectors.


b.

Disconnect the J1*1 and/or I1*2 front No. 1 speaker assembly connector.


c.

Disconnect the L2*1 and/or K2*2 rear speaker assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side:
Tester Connection Condition Specified Condition
G46-2 (FL+) - J1-1 Always Below 1 Ω
G46-6 (FL-) -J1-2 Always Below 1 Ω
G47-2 (RL+) - L2-1 Always Below 1 Ω
G47-6 (RL-) - L2-2 Always Below 1 Ω
G46-2 (FL+) - Body ground Always 10 kΩ or higher
G46-6 (FL-) - Body ground Always 10 kΩ or higher
G47-2 (RL+) - Body ground Always 10 kΩ or higher
G47-6 (RL-) - Body ground Always 10 kΩ or higher

for RH Side:
Tester Connection Condition Specified Condition
G46-1 (FR+) - I1-1 Always Below 1 Ω
G46-5 (FR-) - I1-2 Always Below 1 Ω
G47-1 (RR+) - K2-1 Always Below 1 Ω
G47-3 (RR-) - K2-2 Always Below 1 Ω
G46-1 (FR+) - Body ground Always 10 kΩ or higher
G46-5 (FR-) - Body ground Always 10 kΩ or higher
G47-1 (RR+) - Body ground Always 10 kΩ or higher
G47-3 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Disconnect the J1*1 and/or I1*2 front No. 1 speaker assembly connector.

*1: for LH Side

*2: for RH Side


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT REAR SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.INSPECT REAR SPEAKER ASSEMBLY
a.

Disconnect the L2*1 and/or K2*2 rear speaker assembly connector.

*1: for LH Side

*2: for RH Side


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

*1: for LH Side

*2: for RH Side


a.

Disconnect the G46 and G47 radio receiver assembly connectors.


b.

Disconnect the J1*1 and/or I1*2 front No. 1 speaker assembly connector.


c.

Disconnect the L2*1 and/or K2*2 rear speaker assembly connector.


d.

Disconnect the M38 Telematics transceiver connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side:
Tester Connection Condition Specified Condition
G46-2 (FL+) - J1-1 Always Below 1 Ω
G46-6 (FL-) -J1-2 Always Below 1 Ω
G47-2 (RL+) - L2-1 Always Below 1 Ω
G47-6 (RL-) - L2-2 Always Below 1 Ω
G46-2 (FL+) - Body ground Always 10 kΩ or higher
G46-6 (FL-) - Body ground Always 10 kΩ or higher
G47-2 (RL+) - Body ground Always 10 kΩ or higher
G47-6 (RL-) - Body ground Always 10 kΩ or higher

for RH Side:
Tester Connection Condition Specified Condition
G46-1 (FR+) - M38-2 (SPI+) Always Below 1 Ω
G46-5 (FR-) - M38-3 (SPI-) Always Below 1 Ω
M38-5 (SPO+) - I1-1 Always Below 1 Ω
M38-6 (SPO-) - I1-2 Always Below 1 Ω
G47-1 (RR+) - K2-1 Always Below 1 Ω
G47-3 (RR-) - K2-2 Always Below 1 Ω
G46-1 (FR+) - Body ground Always 10 kΩ or higher
G46-5 (FR-) - Body ground Always 10 kΩ or higher
M38-5 (SPO+) - Body ground Always 10 kΩ or higher
M38-6 (SPO-) - Body ground Always 10 kΩ or higher
G47-1 (RR+) - Body ground Always 10 kΩ or higher
G47-3 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Disconnect the J1*1 and/or I1*2 front No. 1 speaker assembly connector.

*1: for LH Side

*2: for RH Side


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

7.INSPECT REAR SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

7.INSPECT REAR SPEAKER ASSEMBLY
a.

Disconnect the L2*1 and/or K2*2 rear speaker assembly connector.

*1: for LH Side

*2: for RH Side


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK TELEMATICS TRANSCEIVER

NG

8.CHECK TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY