Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The telematics transceiver sends a mute signal to the radio receiver assembly.

The radio receiver assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E350600E03
5,2 6.688,2.198 1.688,0.198 10 false Radio Receiver Assembly 5,1.802 5.458,2 0.458,0.198 10 false G46 0.979,2 3.094,2.25 2.115,0.25 10 false Telematics Transceiver 0.979,1.802 1.438,2 0.458,0.198 10 false M38 1.531,1.052 2.146,1.25 0.615,0.198 10 false MUTE 5.219,1.052 5.833,1.25 0.615,0.198 10 false TMUT 5,0.917 5.156,1.115 0.156,0.198 10 false 8 2.083,0.917 2.323,1.167 0.24,0.25 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E259127C43
1.469,0.531 1.906,0.802 0.438,0.271 1.385,1.927 1.021,0.958 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.531,0.583 2.063,0.844 0.531,0.26 10 false M38 0.688,0.781 1.188,0.99 0.5,0.208 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M38-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G46 radio receiver assembly connector.


b.

Disconnect the M38 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-8 (TMUT) - M38-17 (MUTE) Always Below 1 Ω
G46-8 (TMUT) or M38-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO RECEIVER ASSEMBLY
a.

Reconnect the G46 radio receiver assembly connector.


b.
E176650C35
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.583,0.813 1.99,1.042 0.406,0.229 10 false M38
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M38-17 (MUTE) - Body ground Ignition switch ACC 3.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO RECEIVER ASSEMBLY