Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the radio and display receiver assembly.

It also supplies power from the radio and display receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E350989E04
0.146,0.063 2.219,0.333 2.073,0.271 12 false w/ Telematics Transceiver: 0.146,3.417 2.271,3.708 2.125,0.292 12 false w/o Telematics Transceiver: 0.469,2.125 1.854,2.521 1.385,0.396 10 false Telephone Microphone Assembly 0.406,5.521 1.781,5.896 1.375,0.375 10 false Telephone Microphone Assembly 0.469,2.875 1.781,3.094 1.313,0.219 10 false Map Light Assembly 0.396,6.208 1.708,6.427 1.313,0.219 10 false Map Light Assembly 0.375,6.052 1.688,6.271 1.313,0.219 10 false Q16 0.479,2.698 1.792,2.917 1.313,0.219 10 false Q16 1.74,0.531 2.167,0.74 0.427,0.208 10 false SNS2 1.698,0.948 2.167,1.146 0.469,0.198 10 false MACC 1.708,1.375 2.177,1.573 0.469,0.198 10 false MCO+ 1.729,1.781 2.198,1.979 0.469,0.198 10 false MCO- 3.865,1.042 4.333,1.24 0.469,0.198 10 false MCVD 3.865,1.469 4.333,1.667 0.469,0.198 10 false MCI+ 3.865,1.906 4.333,2.104 0.469,0.198 10 false MCI- 3.865,2.333 4.333,2.531 0.469,0.198 10 false SGND 4.333,1.042 4.802,1.24 0.469,0.198 10 false MCO+ 4.354,1.458 4.823,1.656 0.469,0.198 10 false MCO- 5.979,0.646 6.406,0.854 0.427,0.208 10 false SNS2 6,1.052 6.469,1.25 0.469,0.198 10 false MIN+ 5.99,1.448 6.458,1.646 0.469,0.198 10 false MIN- 5.99,1.896 6.458,2.094 0.469,0.198 10 false SGND 5.167,2.021 5.344,2.198 0.177,0.177 10 false * 5.49,2.021 5.667,2.198 0.177,0.177 10 false * 2.708,2.438 2.885,2.615 0.177,0.177 10 false * 3.365,2.458 3.542,2.635 0.177,0.177 10 false * 3.24,5.844 3.417,6.021 0.177,0.177 10 false * 4.583,5.844 4.76,6.021 0.177,0.177 10 false * 3.667,2.875 5.188,3.104 1.521,0.229 10 false Telematics Transceiver 5.823,2.948 7.042,3.354 1.219,0.406 10 false Radio and Display Receiver Assembly 5.802,2.771 6.313,2.99 0.51,0.219 10 false G143 5.771,0.542 5.917,0.74 0.146,0.198 10 false 6 5.771,0.958 5.917,1.156 0.146,0.198 10 false 5 5.729,1.375 5.906,1.583 0.177,0.208 10 false 19 5.729,1.792 5.906,2 0.177,0.208 10 false 18 4.813,0.969 4.99,1.177 0.177,0.208 10 false 18 4.823,1.385 5,1.594 0.177,0.208 10 false 19 3.625,0.958 3.802,1.167 0.177,0.208 10 false 33 3.625,1.375 3.802,1.583 0.177,0.208 10 false 34 3.615,1.802 3.792,2.01 0.177,0.208 10 false 35 3.615,2.198 3.792,2.406 0.177,0.208 10 false 32 2.219,0.542 2.396,0.75 0.177,0.208 10 false 5 2.219,0.948 2.396,1.156 0.177,0.208 10 false 3 2.219,1.813 2.396,2.021 0.177,0.208 10 false 6 2.219,1.375 2.396,1.583 0.177,0.208 10 false 4 1.688,4.354 2.156,4.552 0.469,0.198 10 false MACC 5.979,4.469 6.448,4.667 0.469,0.198 10 false MACC 5.99,4.865 6.458,5.063 0.469,0.198 10 false MIN+ 1.688,4.771 2.156,4.969 0.469,0.198 10 false MCO+ 1.729,5.188 2.198,5.385 0.469,0.198 10 false MCO- 5.99,5.281 6.458,5.479 0.469,0.198 10 false MIN- 5.979,5.708 6.448,5.906 0.469,0.198 10 false SGND 5.979,4.063 6.406,4.271 0.427,0.208 10 false SNS2 1.719,3.927 2.146,4.135 0.427,0.208 10 false SNS2 5.76,3.948 5.906,4.146 0.146,0.198 10 false 6 5.76,4.781 5.906,4.979 0.146,0.198 10 false 5 5.76,4.375 5.906,4.573 0.146,0.198 10 false 4 5.708,5.198 5.885,5.406 0.177,0.208 10 false 19 5.708,5.583 5.885,5.792 0.177,0.208 10 false 18 0.146,6.49 0.958,6.708 0.813,0.219 10 false *: Shielded 5.781,6.229 7,6.635 1.219,0.406 10 false Radio and Display Receiver Assembly 5.76,6.063 6.271,6.281 0.51,0.219 10 false G143 3.656,2.698 4.167,2.917 0.51,0.219 10 false M38 1.052,0.646 1.479,0.854 0.427,0.208 10 false SNS2 1.01,1.042 1.479,1.24 0.469,0.198 10 false MACC 1.094,1.469 1.563,1.667 0.469,0.198 10 false MIC+ 1.125,1.885 1.594,2.083 0.469,0.198 10 false MIC- 1.063,4.042 1.49,4.25 0.427,0.208 10 false SNS2 1.021,4.448 1.49,4.646 0.469,0.198 10 false MACC 1.094,4.875 1.563,5.073 0.469,0.198 10 false MIC+ 1.115,5.292 1.583,5.49 0.469,0.198 10 false MIC- 1.5,0.552 1.677,0.76 0.177,0.208 10 false 1 1.51,0.969 1.688,1.177 0.177,0.208 10 false 5 1.521,1.385 1.698,1.594 0.177,0.208 10 false 3 1.521,1.813 1.698,2.021 0.177,0.208 10 false 2 1.49,3.958 1.667,4.167 0.177,0.208 10 false 1 1.51,4.375 1.688,4.583 0.177,0.208 10 false 5 1.521,4.792 1.698,5 0.177,0.208 10 false 3 1.521,5.198 1.698,5.406 0.177,0.208 10 false 2 2.208,3.958 2.385,4.167 0.177,0.208 10 false 5 2.208,4.375 2.385,4.583 0.177,0.208 10 false 3 2.219,4.781 2.396,4.99 0.177,0.208 10 false 4 2.219,5.219 2.396,5.427 0.177,0.208 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing telematics transceiver, perform the vehicle contract setting.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-5 (MIN+) - Q16-4 (MCO+) Always Below 1 Ω
G143-4 (MACC) - Q16-3 (MACC) Always Below 1 Ω
G143-19 (MIN-) - Q16-6 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher
G143-4 (MACC) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-6 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


c.
E355981C02
0.354,2.49 0.719,2.76 0.365,0.271 0.188,0.99 0.552,1.26 0.365,0.271 2.125,1.031 2.51,0.406 2.51,0.406 2.677,0.406 true 1.646,1.031 1.292,0.406 1.292,0.406 1.156,0.406 true 2.24,2.688 2.458,2.052 2.458,2.052 2.625,2.052 true 1.729,2.708 1.844,1.833 1.844,1.833 2.01,1.833 true 1.469,2.688 1.344,1.833 1.344,1.833 1.208,1.833 true 1.802,1.042 1.406,0.156 1.406,0.156 1.271,0.156 true 1.208,2.677 1.115,2.052 1.115,2.052 0.979,2.052 true 1.969,1.042 2.323,0.177 2.323,0.177 2.49,0.177 true 0.156,0.083 0.469,0.281 0.313,0.198 10 false *a 0.323,1.042 0.479,1.24 0.156,0.198 10 false A 0.49,2.542 0.646,2.74 0.156,0.198 10 false B 2.74,0.344 3.354,0.542 0.615,0.198 10 false MACC 0.885,0.073 1.5,0.271 0.615,0.198 10 false SNS2 0.729,0.302 1.344,0.5 0.615,0.198 10 false MCO- 2.688,1.979 3.302,2.177 0.615,0.198 10 false MACC 2.073,1.75 2.688,1.948 0.615,0.198 10 false MIC+ 0.875,1.74 1.49,1.938 0.615,0.198 10 false MIC- 0.552,1.979 1.167,2.177 0.615,0.198 10 false SNS2 2.531,0.104 3.146,0.302 0.615,0.198 10 false MCO+
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (MACC) - B-5 (MACC) Always Below 1 Ω
A-4 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-6 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-3 (MACC) - A-4 (MCO+) Always 10 kΩ or higher
A-3 (MACC) - A-5 (SNS2) Always 10 kΩ or higher
A-3 (MACC) - A-6 (MCO-) Always 10 kΩ or higher
A-4 (MCO+) - A-5 (SNS2) Always 10 kΩ or higher
A-4 (MCO+) - A-6 (MCO-) Always 10 kΩ or higher
A-5 (SNS2) - A-6 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the M38 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-5 (MIN+) - M38-18 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - M38-19 (MCO-) Always Below 1 Ω
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the M38 telematics transceiver connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-33 (MCVD) - Q16-3 (MACC) Always Below 1 Ω
M38-34 (MCI+) - Q16-4 (MCO+) Always Below 1 Ω
M38-35 (MCI-) - Q16-6 (MCO-) Always Below 1 Ω
M38-33 (MCVD) - Body ground Always 10 kΩ or higher
M38-34 (MCI+) - Body ground Always 10 kΩ or higher
M38-35 (MCI-) - Body ground Always 10 kΩ or higher
M38-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


c.
E355981C02
0.354,2.49 0.719,2.76 0.365,0.271 0.188,0.99 0.552,1.26 0.365,0.271 2.125,1.031 2.51,0.406 2.51,0.406 2.677,0.406 true 1.646,1.031 1.292,0.406 1.292,0.406 1.156,0.406 true 2.24,2.688 2.458,2.052 2.458,2.052 2.625,2.052 true 1.729,2.708 1.844,1.833 1.844,1.833 2.01,1.833 true 1.469,2.688 1.344,1.833 1.344,1.833 1.208,1.833 true 1.802,1.042 1.406,0.156 1.406,0.156 1.271,0.156 true 1.208,2.677 1.115,2.052 1.115,2.052 0.979,2.052 true 1.969,1.042 2.323,0.177 2.323,0.177 2.49,0.177 true 0.156,0.083 0.469,0.281 0.313,0.198 10 false *a 0.323,1.042 0.479,1.24 0.156,0.198 10 false A 0.49,2.542 0.646,2.74 0.156,0.198 10 false B 2.74,0.344 3.354,0.542 0.615,0.198 10 false MACC 0.885,0.073 1.5,0.271 0.615,0.198 10 false SNS2 0.729,0.302 1.344,0.5 0.615,0.198 10 false MCO- 2.688,1.979 3.302,2.177 0.615,0.198 10 false MACC 2.073,1.75 2.688,1.948 0.615,0.198 10 false MIC+ 0.875,1.74 1.49,1.938 0.615,0.198 10 false MIC- 0.552,1.979 1.167,2.177 0.615,0.198 10 false SNS2 2.531,0.104 3.146,0.302 0.615,0.198 10 false MCO+
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (MACC) - B-5 (MACC) Always Below 1 Ω
A-4 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-6 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-3 (MACC) - A-4 (MCO+) Always 10 kΩ or higher
A-3 (MACC) - A-5 (SNS2) Always 10 kΩ or higher
A-3 (MACC) - A-6 (MCO-) Always 10 kΩ or higher
A-4 (MCO+) - A-5 (SNS2) Always 10 kΩ or higher
A-4 (MCO+) - A-6 (MCO-) Always 10 kΩ or higher
A-5 (SNS2) - A-6 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

9.CHECK TELEMATICS TRANSCEIVER
a.

Disconnect the Q16 map light assembly connector.


b.
E283057C29
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.677,0.667 2.177,0.844 0.5,0.177 10 false M38
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M38-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-32 (SGND) - Body ground Always Below 1 Ω
M38-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

10.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY