Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E357367E01
0.073,3.031 2.531,3.323 2.458,0.292 10 false No. 1 Stereo Jack Adapter Assembly 0.188,3.469 1.177,3.75 0.99,0.281 10 false *: Shielded 5.542,3.052 7.156,3.385 1.615,0.333 10 false Radio Receiver Assembly 5.542,2.833 6,3.031 0.458,0.198 10 false G48 5.969,2.417 6.583,2.615 0.615,0.198 10 false AGND 5.969,1.906 6.583,2.104 0.615,0.198 10 false VA- 5.99,1.448 6.604,1.646 0.615,0.198 10 false VAL+ 5.969,0.969 6.583,1.167 0.615,0.198 10 false VAR+ 5.99,0.479 6.604,0.677 0.615,0.198 10 false ADPG 0.781,0.49 1.396,0.688 0.615,0.198 10 false AUXO 0.854,0.979 1.469,1.177 0.615,0.198 10 false ARO 0.865,1.458 1.479,1.656 0.615,0.198 10 false ALO 0.813,1.938 1.427,2.135 0.615,0.198 10 false ASGN 2.708,2.594 2.99,2.865 0.281,0.271 10 false * 4.354,2.563 4.635,2.833 0.281,0.271 10 false * 0.76,2.438 1.375,2.635 0.615,0.198 10 false AGND 0.063,2.844 0.521,3.042 0.458,0.198 10 false G145 1.354,0.375 1.51,0.573 0.156,0.198 10 false 8 1.333,0.833 1.49,1.031 0.156,0.198 10 false 5 1.323,1.333 1.479,1.531 0.156,0.198 10 false 6 1.333,1.813 1.49,2.01 0.156,0.198 10 false 7 1.323,2.313 1.479,2.51 0.156,0.198 10 false 9 5.656,0.854 5.875,1.073 0.219,0.219 10 false 26 5.656,0.344 5.875,0.563 0.219,0.219 10 false 25 5.646,1.313 5.865,1.531 0.219,0.219 10 false 28 5.615,1.802 5.833,2.021 0.219,0.219 10 false 27 5.594,2.281 5.813,2.5 0.219,0.219 10 false 11

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G48 radio receiver assembly connector.


b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G145-8 (AUXO) - G48-25 (ADPG) Always Below 1 Ω
G145-5 (ARO) - G48-26 (VAR+) Always Below 1 Ω
G145-6 (ALO) - G48-28 (VAL+) Always Below 1 Ω
G145-7 (ASGN) - G48-27 (VA-) Always Below 1 Ω
G145-9 (AGND) - G48-11 (AGND) Always Below 1 Ω
G145-8 (AUXO) - Body ground Always 10 kΩ or higher
G145-5 (ARO) - Body ground Always 10 kΩ or higher
G145-6 (ALO) - Body ground Always 10 kΩ or higher
G145-7 (ASGN) - Body ground Always 10 kΩ or higher
G145-9 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR