Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2016.08
RM3090E _53 Suspension _008764 FRONT SUSPENSION _0049353 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 2.DISCONNECT FRONT SPEED SENSOR LH

a.
C276122

Remove the bolt, detach the clamp and disconnect the front speed sensor.

NOTICE:

Be sure to completely disconnect the front speed sensor from the front shock absorber with coil spring.



Hide 48810 3.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C284566

Remove the nut and disconnect the stabilizer link assembly from the front shock absorber with coil spring.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 47313A 4.DISCONNECT FRONT FLEXIBLE HOSE

a.
C153576

Remove the bolt and disconnect the front flexible hose.


Hide 48684B 5.REMOVE FRONT SUSPENSION SUPPORT DUST COVER LH

a.

Remove the front suspension support dust cover LH.


Hide 6.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C158628C01
0.417,1.448 0.74,1.448 false 2.438,1.969 2.729,1.698 2.729,1.698 3,1.698 false 0.219,1.365 0.531,1.521 0.313,0.156 10 false *a 3.073,1.635 3.385,1.792 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Support the front lower arm using a jack and wooden block.


b.
C117406

Loosen the front support to front shock absorber nut of the front shock absorber.

NOTICE:
·

Do not remove the front support to front shock absorber nut.

·

Loosen the nut only when the front shock absorber with coil spring needs to be disassembled.




c.
C117407

Remove the 2 bolts and 2 nuts and disconnect the front shock absorber with coil spring from the steering knuckle.


d.
C117405

Remove the 3 nuts, front fender apron rear extension LH and front shock absorber with coil spring.

NOTICE:

Make sure that the front speed sensor is completely disconnected from the front shock absorber with coil spring.



Hide 48687B 7.REMOVE FRONT SUSPENSION SUPPORT PLATE LH

a.
C225289

Remove the front suspension support plate from the front shock absorber with coil spring.


Hide 48520 8.REMOVE FRONT SHOCK ABSORBER ASSEMBLY LH

a.
C266189N02
0.521,1.427 0.938,1.427 false 0.198,1.333 0.656,1.531 0.458,0.198 10 SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706C07
0.26,0.167 0.573,0.323 0.313,0.156 10 *a 0.354,2.51 0.667,2.667 0.313,0.156 10 *b
*a Correct
*b Incorrect


Attach the arm of SST to the diameter of the coil spring.

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.

Confirm that the coil spring becomes free and remove the front support to front shock absorber nut and collar.

CAUTION:

Do not remove the front support to front shock absorber nut when the coil spring is not free.



e.

Remove the front suspension support sub-assembly.


f.

Remove the strut mounting bearing from the front suspension support.


g.

Remove the front spring seat sub-assembly with insulator LH.


h.

Remove the spring bumper from the shock absorber.


i.

Remove the lower insulator from the shock absorber.


j.

Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench.