Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


CHECK DTC (USING GTS)


a.

Connect the GTS to the DLC3.


b.

Engine start.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.

Body Electrical > Navigation System > Trouble Codes
50001 212



CLEAR DTC (USING GTS)


a.

Connect the GTS to the DLC3.


b.

Engine start.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212


START DIAGNOSTIC MODE (NOT USING GTS, for 6.1 Inch Display)


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

·

Start diagnostic mode using either of the 2 methods below.



a.

Method 1

i.
E307147C03
0.135,0.073 0.448,0.229 0.313,0.156 10 false *A 0.167,2.5 0.479,2.656 0.313,0.156 10 false *B 1.271,1.104 1.583,1.26 0.313,0.156 10 false *a 2.063,1.323 2.375,1.479 0.313,0.156 10 false *b 2.063,3.333 2.375,3.49 0.313,0.156 10 false *c 1.24,3.594 1.552,3.75 0.313,0.156 10 false *d
*A for LHD
*B for RHD
*a "MEDIA" Switch
*b "CAR" Switch


Start the engine.


ii.

While pressing and holding the "CAR" or "MEDIA" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


iii.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



b.

Method 2

NOTICE:

If the operation fails and diagnostic mode cannot be entered, turn the radio and display receiver assembly screen display on and off once, and then perform the procedures listed below from the first step again. (Only turning the radio and display receiver assembly power supply on and off will not work.)


i.
E309126C03
0.208,0.125 0.458,0.313 0.25,0.188 10 false *A 0.24,2.354 0.49,2.542 0.25,0.188 10 false *B 1.302,1.302 1.552,1.49 0.25,0.188 10 false *a 1.302,1.563 1.552,1.75 0.25,0.188 10 false *b 2,3.573 2.25,3.76 0.25,0.188 10 false *a 2,3.833 2.25,4.021 0.25,0.188 10 false *b
*A for LHD
*B for RHD
*a ">" Switch
*b "<" Switch


Start the engine.


ii.

Turn the radio and display receiver assembly screen display off.


iii.

Turn the radio and display receiver assembly power supply off.


iv.

Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.


v.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.




START DIAGNOSTIC MODE (NOT USING GTS, for 7 Inch Display)


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

·

Start diagnostic mode using either of the 2 methods below.



a.

Method 1

i.
E335186C01
0.344,0.219 0.656,0.417 0.313,0.198 10 false *A 0.417,2.479 0.729,2.677 0.313,0.198 10 false *B 1.198,1.104 1.51,1.302 0.313,0.198 10 false *a 2.063,1.26 2.375,1.458 0.313,0.198 10 false *b 1.219,3.5 1.531,3.698 0.313,0.198 10 false *b 2.094,3.333 2.406,3.531 0.313,0.198 10 false *a
*A for LHD
*B for RHD
*a "MEDIA" Switch
*b "CAR" Switch


Start the engine.


ii.

While pressing and holding the "CAR" or "MEDIA" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


iii.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



b.

Method 2

NOTICE:

If the operation fails and diagnostic mode cannot be entered, turn the radio and display receiver assembly screen display on and off once, and then perform the procedures listed below from the first step again. (Only turning the radio and display receiver assembly power supply on and off will not work.)


i.
E335187C01
0.375,0.24 0.688,0.438 0.313,0.198 10 false *A 0.438,2.448 0.75,2.646 0.313,0.198 10 false *B 1.177,1.24 1.385,1.427 0.208,0.188 10 false *a 1.177,1.448 1.354,1.635 0.177,0.188 10 false *b 2.083,3.448 2.323,3.625 0.24,0.177 10 false *a 2.083,3.625 2.313,3.792 0.229,0.167 10 false *b
*A for LHD
*B for RHD
*a ">" Switch
*b "<" Switch


Start the engine.


ii.

Turn the radio and display receiver assembly screen display off.


iii.

Turn the radio and display receiver assembly power supply off.


iv.

Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.


v.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.




FAILURE DIAGNOSIS


a.
E278177

Press the "Failure Diagnosis" switch on the "Service Menu" screen.


b.

The "Failure Diagnosis" will be displayed.



SYSTEM CHECK


a.
E353082

Press the "System Check" switch on the "Failure Diagnosis" screen.


b.

The "System Check Mode" screen will be displayed.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E353083E01
0.281,0.583 0.531,0.583 true 1,1.833 1,0.667 true 2.083,1.917 2.083,1.667 true 2.667,1.917 2.667,1.667 true 3.083,0.917 2.917,0.917 true 0.104,0.5 0.417,0.698 0.313,0.198 10 false *a 0.938,1.917 1.25,2.115 0.313,0.198 10 false *b 2,1.917 2.25,2.083 0.25,0.167 10 false *c 2.583,1.917 2.896,2.115 0.313,0.198 10 false *d 3.104,0.833 3.417,1.031 0.313,0.198 10 false *e

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 1 are shown in the following table


*b: Check Result Result codes for all devices are displayed
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared

·

Press the "Memory CLR" switch for 3 seconds


*d: Recheck
·

A system check will be performed again after the memory is cleared

·

The "Recheck" switch will dim during a system check


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 2 are shown in the following table



*a: Device Name List No. 1 Description
Name Component Connection Method

*: w/ Panoramic View Monitor System

DA Radio and display receiver assembly -
CAMERA-C Parking assist ECU* Communication line for AVC-LAN

*b: Check Result Description
Result Meaning Action

*: As these functions are not equipped on the vehicle, they are not displayed.

OK The device does not respond with a DTC -
DETAIL The device responds with a DTC Look up the DTC in "Unit Check Mode"
NCON* The device was previously present, but does not respond in diagnostic mode Check power supply wire harness of the device
NRES* The device responds in diagnostic mode, but gives no DTC information Check power supply wire harness of the device

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E226127N06
0.917,0.094 1.115,0.094 1.115,0.094 1.365,0.604 true 0.313,0.688 0.677,0.688 true 1.823,0.094 1.615,0.094 1.615,0.094 1.458,0.438 true 0.875,1.104 0.875,1.896 true 2.906,1.667 3.125,1.667 true 0.719,0.0 0.875,0.156 0.156,0.156 10 *b 0.115,0.594 0.583,0.979 0.469,0.385 10 *c 0.792,1.917 1.115,2.104 0.323,0.188 10 *d 1.854,0.0 2.01,0.156 0.156,0.156 10 *a 3.167,1.573 3.396,1.844 0.229,0.271 10 *e

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared.).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.

Read the system check result.

i.

If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", this means that no DTCs are stored.

·

When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.







DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E353084

Clear DTCs

i.

Press the "Memory CLR" switch for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.





b.

Recheck

i.
E353085

Press the "Recheck" switch.


ii.
E353086

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

HINT:

When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the ignition switch off.