Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E229861E69
0.813,0.813 1.24,0.969 0.427,0.156 10 false AUXO 0.896,1.281 1.323,1.438 0.427,0.156 10 false ARO 0.938,1.75 1.365,1.906 0.427,0.156 10 false ALO 0.813,2.229 1.24,2.385 0.427,0.156 10 false ASGN 0.813,2.708 1.24,2.865 0.427,0.156 10 false AGND 0.292,4.25 1.208,4.521 0.917,0.271 10 false *: Shielded 4.375,2.917 4.698,3.125 0.323,0.208 10 false * 5.927,0.729 6.354,0.885 0.427,0.156 10 false ADPG 5.927,1.219 6.354,1.375 0.427,0.156 10 false VAR+ 5.688,0.677 5.865,0.833 0.177,0.156 10 false 25 5.698,1.167 5.875,1.323 0.177,0.156 10 false 26 5.698,1.625 5.875,1.781 0.177,0.156 10 false 28 5.698,2.115 5.875,2.271 0.177,0.156 10 false 27 5.698,2.583 5.875,2.74 0.177,0.156 10 false 11 1.323,0.688 1.5,0.844 0.177,0.156 10 false 8 1.323,1.146 1.5,1.302 0.177,0.156 10 false 5 1.323,1.615 1.5,1.771 0.177,0.156 10 false 6 1.323,2.083 1.5,2.24 0.177,0.156 10 false 7 1.323,2.594 1.5,2.75 0.177,0.156 10 false 9 0.438,3.219 0.792,3.375 0.354,0.156 10 false G145 0.417,3.385 1.604,3.781 1.188,0.396 10 false No. 1 Stereo Jack Adapter Assembly 5.802,3.354 7.031,3.729 1.229,0.375 10 false Radio and Display Receiver Assembly 5.927,1.667 6.354,1.823 0.427,0.156 10 false VAL+ 5.927,2.177 6.354,2.333 0.427,0.156 10 false VA- 5.927,2.635 6.354,2.792 0.427,0.156 10 false AGND 5.802,3.177 6.313,3.365 0.51,0.188 10 false G143 2.771,2.896 3.094,3.104 0.323,0.208 10 false *

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G145-8 (AUXO) - G143-25 (ADPG) Always Below 1 Ω
G145-5 (ARO) - G143-26 (VAR+) Always Below 1 Ω
G145-6 (ALO) - G143-28 (VAL+) Always Below 1 Ω
G145-7 (ASGN) - G143-27 (VA-) Always Below 1 Ω
G145-9 (AGND) - G143-11 (AGND) Always Below 1 Ω
G145-8 (AUXO) - Body ground Always 10 kΩ or higher
G145-5 (ARO) - Body ground Always 10 kΩ or higher
G145-6 (ALO) - Body ground Always 10 kΩ or higher
G145-7 (ASGN) - Body ground Always 10 kΩ or higher
G145-9 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR