Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

w/o Telematics Transceiver:

The radio and display receiver assemblyand telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assemblysends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly.


w/ Telematics Transceiver:

The radio and display receiver assemblyand telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


WIRING DIAGRAM

E357368E01
0.229,0.094 2.604,0.354 2.375,0.26 12 false w/ Telematics Transceiver: 0.24,3.979 2.615,4.24 2.375,0.26 12 false w/o Telematics Transceiver: 0.5,6.188 1.906,6.906 1.406,0.719 10 false Telephone Microphone Assembly 0.521,2.396 1.927,3.115 1.406,0.719 10 false Telephone Microphone Assembly 5.719,3.052 6.927,3.698 1.208,0.646 10 false Radio and Display Receiver Assembly 5.708,7.063 6.917,7.604 1.208,0.542 10 false Radio and Display Receiver Assembly 5.708,6.844 6.323,7.042 0.615,0.198 10 false G143 5.729,2.844 6.344,3.042 0.615,0.198 10 false G143 3.708,2.948 4.323,3.146 0.615,0.198 10 false M38 3.708,3.146 5.177,3.552 1.469,0.406 10 false Telematics Transceiver 0.74,0.885 1.354,1.083 0.615,0.198 10 false SNS2 1.688,0.75 2.302,0.948 0.615,0.198 10 false SNS2 6.01,0.865 6.625,1.063 0.615,0.198 10 false SNS2 0.75,4.802 1.365,5 0.615,0.198 10 false SNS2 1.688,4.656 2.302,4.854 0.615,0.198 10 false SNS2 6.021,4.802 6.635,5 0.615,0.198 10 false SNS2 0.76,1.25 1.375,1.448 0.615,0.198 10 false MACC 1.667,1.135 2.281,1.333 0.615,0.198 10 false MACC 6.031,5.156 6.646,5.354 0.615,0.198 10 false MACC 1.688,5.021 2.302,5.219 0.615,0.198 10 false MACC 0.75,5.104 1.365,5.302 0.615,0.198 10 false MACC 0.75,1.646 1.365,1.844 0.615,0.198 10 false MIC+ 0.75,2.052 1.365,2.25 0.615,0.198 10 false MIC- 1.708,1.51 2.323,1.708 0.615,0.198 10 false MCO+ 1.719,1.938 2.333,2.135 0.615,0.198 10 false MCO- 4.313,1.26 4.927,1.458 0.615,0.198 10 false MCO+ 4.344,1.646 4.958,1.844 0.615,0.198 10 false MCO- 3.865,1.25 4.479,1.448 0.615,0.198 10 false MCVD 3.875,1.646 4.49,1.844 0.615,0.198 10 false MCI+ 3.885,2.073 4.5,2.271 0.615,0.198 10 false MCI- 3.885,2.552 4.5,2.75 0.615,0.198 10 false SGND 6.01,1.271 6.625,1.469 0.615,0.198 10 false MIN+ 6.01,1.677 6.625,1.875 0.615,0.198 10 false MIN- 6.01,2.146 6.625,2.344 0.615,0.198 10 false SGND 2.74,2.698 2.896,2.896 0.156,0.198 10 false * 3.042,2.719 3.198,2.917 0.156,0.198 10 false * 3.365,2.708 3.521,2.906 0.156,0.198 10 false * 5.177,2.26 5.333,2.458 0.156,0.198 10 false * 5.479,2.26 5.635,2.458 0.156,0.198 10 false * 5.75,0.75 5.906,0.948 0.156,0.198 10 false 6 5.75,1.135 5.906,1.333 0.156,0.198 10 false 5 5.729,1.552 5.958,1.75 0.229,0.198 10 false 19 5.729,1.969 5.958,2.167 0.229,0.198 10 false 18 4.833,1.135 5.063,1.333 0.229,0.198 10 false 18 4.833,1.552 5.063,1.75 0.229,0.198 10 false 19 2.26,0.75 2.417,0.948 0.156,0.198 10 false 5 2.26,1.135 2.417,1.333 0.156,0.198 10 false 3 2.26,1.552 2.417,1.75 0.156,0.198 10 false 4 2.26,1.917 2.417,2.115 0.156,0.198 10 false 6 3.604,1.156 3.823,1.354 0.219,0.198 10 false 33 3.615,1.521 3.833,1.719 0.219,0.198 10 false 34 3.604,1.948 3.823,2.146 0.219,0.198 10 false 35 3.615,2.396 3.833,2.594 0.219,0.198 10 false 32 0.375,3.188 0.99,3.385 0.615,0.198 10 false Q16 0.375,3.396 2,3.75 1.625,0.354 10 false Map Light Assembly 0.396,7.188 2.021,7.542 1.625,0.354 10 false Map Light Assembly 0.396,7 1.01,7.198 0.615,0.198 10 false Q16 0.271,7.531 1.135,7.802 0.865,0.271 10 false *: Shielded 0.75,5.469 1.365,5.667 0.615,0.198 10 false MIC+ 1.698,5.365 2.313,5.563 0.615,0.198 10 false MCO+ 0.75,5.802 1.365,6 0.615,0.198 10 false MIC- 1.698,5.719 2.313,5.917 0.615,0.198 10 false MCO- 3.208,6.313 3.365,6.51 0.156,0.198 10 false * 4.719,6.333 4.875,6.531 0.156,0.198 10 false * 6.042,5.469 6.656,5.667 0.615,0.198 10 false MIN+ 6.052,5.802 6.667,6 0.615,0.198 10 false MIN- 6.021,6.125 6.635,6.323 0.615,0.198 10 false SGND 5.75,4.646 5.906,4.844 0.156,0.198 10 false 6 5.74,5.375 5.885,5.563 0.146,0.188 10 false 5 5.75,5.031 5.917,5.219 0.167,0.188 10 false 4 5.698,5.719 5.917,5.917 0.219,0.198 10 false 19 5.698,6.031 5.917,6.229 0.219,0.198 10 false 18 2.281,4.604 2.438,4.802 0.156,0.198 10 false 5 2.292,5.031 2.448,5.229 0.156,0.198 10 false 3 2.302,5.385 2.458,5.583 0.156,0.198 10 false 4 2.313,5.719 2.469,5.917 0.156,0.198 10 false 6 1.344,5 1.5,5.198 0.156,0.198 10 false 5 1.344,5.333 1.5,5.531 0.156,0.198 10 false 3 1.344,5.667 1.5,5.865 0.156,0.198 10 false 2 1.344,4.667 1.5,4.865 0.156,0.198 10 false 1 1.333,0.75 1.49,0.948 0.156,0.198 10 false 1 1.333,1.135 1.49,1.333 0.156,0.198 10 false 5 1.333,1.552 1.49,1.75 0.156,0.198 10 false 3 1.344,1.969 1.5,2.167 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω
G143-4 (MACC) - Q16-3 (MACC) Always Below 1 Ω
G143-5 (MIN+) - Q16-4 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - Q16-6 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Body ground Always 10 kΩ or higher
G143-4 (MACC) - Body ground Always 10 kΩ or higher
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.
E355981N01
0.354,2.49 0.719,2.76 0.365,0.271 0.188,0.99 0.552,1.26 0.365,0.271 2.125,1.052 2.344,0.417 2.344,0.417 2.51,0.417 true 1.948,1.063 2.063,0.219 2.063,0.219 2.229,0.219 true 1.615,1.063 1.521,0.438 1.521,0.438 1.385,0.438 true 2.24,2.688 2.458,2.052 2.458,2.052 2.625,2.052 true 1.76,2.833 2.042,3.25 2.042,3.25 2.208,3.25 true 1.427,2.688 1.333,2.063 1.333,2.063 1.198,2.063 true 1.156,2.833 0.875,3.104 0.875,3.104 0.74,3.104 true 1.802,1.135 1.865,1.813 1.865,1.813 2.031,1.813 true 0.323,1.042 0.479,1.24 0.156,0.198 10 false A 0.49,2.542 0.646,2.74 0.156,0.198 10 false B 2.563,0.333 3.177,0.531 0.615,0.198 10 false MACC 2.281,0.146 2.896,0.344 0.615,0.198 10 false MCO+ 0.948,0.344 1.563,0.542 0.615,0.198 10 false MCO- 2.677,1.969 3.292,2.167 0.615,0.198 10 false MACC 2.292,3.167 2.906,3.365 0.615,0.198 10 false MIC+ 0.844,1.969 1.458,2.167 0.615,0.198 10 false MIC- 2.094,1.729 2.708,1.927 0.615,0.198 10 false SNS2 0.323,3.01 0.938,3.208 0.615,0.198 10 false SNS2

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (MACC) - B-5 (MACC) Always Below 1 Ω
A-4 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-6 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-3 (MACC) - A-4 (MCO+) Always 10 kΩ or higher
A-3 (MACC) - A-5 (SNS2) Always 10 kΩ or higher
A-3 (MACC) - A-6 (MCO-) Always 10 kΩ or higher
A-4 (MCO+) - A-5 (SNS2) Always 10 kΩ or higher
A-4 (MCO+) - A-6 (MCO-) Always 10 kΩ or higher
A-5 (SNS2) - A-6 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the M38 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-5 (MIN+) - M38-18 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - M38-19 (MCO-) Always Below 1 Ω
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the M38 telematics transceiver connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-33 (MCVD) - Q16-3 (MACC) Always Below 1 Ω
M38-34 (MCI+) - Q16-4 (MCO+) Always Below 1 Ω
M38-35 (MCI-) - Q16-6 (MCO-) Always Below 1 Ω
M38-33 (MCVD) - Body ground Always 10 kΩ or higher
M38-34 (MCI+) - Body ground Always 10 kΩ or higher
M38-35 (MCI-) - Body ground Always 10 kΩ or higher
M38-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.
E355981N01
0.354,2.49 0.719,2.76 0.365,0.271 0.188,0.99 0.552,1.26 0.365,0.271 2.125,1.052 2.344,0.417 2.344,0.417 2.51,0.417 true 1.948,1.063 2.063,0.219 2.063,0.219 2.229,0.219 true 1.615,1.063 1.521,0.438 1.521,0.438 1.385,0.438 true 2.24,2.688 2.458,2.052 2.458,2.052 2.625,2.052 true 1.76,2.833 2.042,3.25 2.042,3.25 2.208,3.25 true 1.427,2.688 1.333,2.063 1.333,2.063 1.198,2.063 true 1.156,2.833 0.875,3.104 0.875,3.104 0.74,3.104 true 1.802,1.135 1.865,1.813 1.865,1.813 2.031,1.813 true 0.323,1.042 0.479,1.24 0.156,0.198 10 false A 0.49,2.542 0.646,2.74 0.156,0.198 10 false B 2.563,0.333 3.177,0.531 0.615,0.198 10 false MACC 2.281,0.146 2.896,0.344 0.615,0.198 10 false MCO+ 0.948,0.344 1.563,0.542 0.615,0.198 10 false MCO- 2.677,1.969 3.292,2.167 0.615,0.198 10 false MACC 2.292,3.167 2.906,3.365 0.615,0.198 10 false MIC+ 0.844,1.969 1.458,2.167 0.615,0.198 10 false MIC- 2.094,1.729 2.708,1.927 0.615,0.198 10 false SNS2 0.323,3.01 0.938,3.208 0.615,0.198 10 false SNS2

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (MACC) - B-5 (MACC) Always Below 1 Ω
A-4 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-6 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-3 (MACC) - A-4 (MCO+) Always 10 kΩ or higher
A-3 (MACC) - A-5 (SNS2) Always 10 kΩ or higher
A-3 (MACC) - A-6 (MCO-) Always 10 kΩ or higher
A-4 (MCO+) - A-5 (SNS2) Always 10 kΩ or higher
A-4 (MCO+) - A-6 (MCO-) Always 10 kΩ or higher
A-5 (SNS2) - A-6 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

9.CHECK TELEMATICS TRANSCEIVER
a.
E283057C23
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.667,0.667 2.167,0.844 0.5,0.177 10 false M38
*a Component with harness connected
(Telematics Transceiver)


Disconnect the Q16 map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M38-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-32 (SGND) - Body ground Always Below 1 Ω
M38-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY