Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

Telematics transceiver sends a mute signal to the radio and display receiver assembly.

The radio and display receiver assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E336503E26
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.719,0.906 2.333,1.104 0.615,0.198 10 false 8 5.292,0.917 5.906,1.115 0.615,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.677,1.948 1.292,2.146 0.615,0.198 10 false G141 0.719,2.115 1.927,2.604 1.208,0.49 10 false Radio and Display Receiver Assembly 5.125,2.042 6.656,2.313 1.531,0.271 10 false Telematics Transceiver 5.115,1.896 5.729,2.094 0.615,0.198 10 false M38

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION



PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E259127C43
1.469,0.531 1.906,0.802 0.438,0.271 1.385,1.927 1.021,0.958 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.531,0.583 2.063,0.844 0.531,0.26 10 false M38 0.688,0.781 1.188,0.99 0.5,0.208 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M38-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G141 radio and display receiver assembly connector.


b.

Disconnect the M38 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-8 (TMUT) - M38-17 (MUTE) Always Below 1 Ω
G141-8 (TMUT) or M38-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the G141 radio and display receiver assembly connector.


b.
E176650C35
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.583,0.813 1.99,1.042 0.406,0.229 10 false M38
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M38-17 (MUTE) - Body ground Ignition switch ACC 3.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY