Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM U

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A342925E01
2.333,0.448 2.729,0.698 0.396,0.25 5.885,0.448 6.281,0.698 0.396,0.25 5.948,0.49 6.406,0.688 0.458,0.198 10 false A62 2.406,0.49 2.865,0.688 0.458,0.198 10 false B93

HINT:

The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of the terminals, which is displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-1 (BATT) - B93-59 (E1) W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A62-2 (+B) - B93-59 (E1) R - BR Power source of ECM Ignition switch ON 11 to 14 V
A62-3 (+B2) - B93-59 (E1) P - BR Power source of ECM Ignition switch ON 11 to 14 V
A62-5 (ELS1) - B93-59 (E1) G - BR Electric load signal Taillight switch on 7.5 to 14 V
Taillight switch off Below 1.5 V
A62-6 (IGSW) - B93-59 (E1) B - BR Ignition switch signal Ignition switch ON 11 to 14 V
A62-7 (FANL) - B93-59 (E1) R - BR FAN NO.3 relay operation signal Ignition switch ON 11 to 14 V
Idling with A/C on or high engine coolant temperature Below 1.5 V
A62-8 (FANH) - B93-59 (E1) W - BR FAN NO.1 and NO.2 relay operation signal Idling with high engine coolant temperature Below 1.5 V
A62-9 (STP) - B93-59 (E1) L - BR Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A62-10 (ST1-) - B93-59 (E1) GR - BR Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON, Brake pedal depressed Below 1.5 V
Ignition switch ON, Brake pedal released 7.5 to 14 V
A62-13 (CANH) - B93-59 (E1) Y - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A62-23 (NSW)*1 - B93-59 (E1) W - BR Park/Neutral position switch assembly signal Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
A62-26 (CANL) - B93-59 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A62-27 (W) - B93-59 (E1) R - BR Malfunction Indicator Lamp (MIL) operation signal Ignition switch ON (MIL goes off) Below 1.5 V
Idling 11 to 14 V
A62-29 (STA) - B93-59 (E1) V*1 - BR
SB*2 - BR
Starter assembly signal Cranking 5.5 V or higher
A62-30 (NEO) - B93-59 (E1) LG - BR Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 3)
A62-31 (TACH) - B93-59 (E1) GR - BR Engine speed signal Idling Pulse generation
(See waveform 4)
A62-32 (EC) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A62-33 (TC) - B93-59 (E1) G - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A62-34 (ELS2) - B93-59 (E1) P - BR Electric load signal Defogger switch on 7.5 to 14 V
Defogger switch off Below 1.5 V
A62-41 (FC) - B93-59 (E1) W - BR Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A62-44 (SPD) - B93-59 (E1) V - BR Vehicle speed signal from combination meter assembly signal Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A62-46 (MREL) - B93-59 (E1) P - BR EFI-MAIN NO.1 relay operation signal Ignition switch ON 11 to 14 V
A62-47 (VPA) - A62-48 (EPA) W - Y Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A62-49 (VCPA) - A62-48 (EPA) B - Y Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A62-50 (VPA2) - A62-51 (EPA2) R - P Accelerator pedal position sensor signal (for sensor malfunctioning detection) Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed 3.4 to 4.75 V
A62-52 (VCP2) - A62-51 (EPA2) L - P Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
B93-26 (E04) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
B93-27 (HA1A) - B93-26 (E04) L - W-B Air fuel ratio sensor heater operation signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See WAVEFORM 6)
B93-28 (ME01) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
B93-29 (+BM) - B93-59 (E1) L - BR Power source of throttle actuator Always 11 to 14 V
B93-30 (M-) - B93-28 (ME01) P - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See WAVEFORM 7)
B93-31 (CAN+) - B93-59 (E1) Y - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
B93-32 (CAN-) - B93-59 (E1) L - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
B93-33 (PRG) - B93-59 (E1) G - BR Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See WAVEFORM 8)
B93-35 (OC1+) - B93-34 (OC1-) W - B Camshaft timing oil control valve assembly (for intake camshaft) operation signal Idling Pulse generation
(See WAVEFORM 9)
B93-37 (OE1+) - B93-36 (OE1-) R - LG Camshaft timing oil control valve assembly (for exhaust camshaft) operation signal Idling Pulse generation
(See WAVEFORM 10)
B93-56 (HT1B) - B93-59 (E1) R - BR Heated oxygen sensor heater operation signal Ignition switch ON 11 to 14 V
Idling Below 3.0 V
B93-57 (E01) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
B93-58 (E02) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
B93-59 (E1) - Body ground BR - Body ground Ground circuit of ECM Always Below 1 Ω
B93-60 (M+) - B93-28 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See WAVEFORM 11)
B93-62 (ACIS) - B93-59 (E1) R - BR Vacuum switching valve (for acoustic control induction system) operation signal Ignition switch ON 11 to 14 V
B93-71 (IGF1) - B93-59 (E1) W - BR Ignition coil assembly
(ignition confirmation signal)
Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(See WAVEFORM 12)
B93-72 (IGT4) - B93-59 (E1) L - BR No. 4 ignition coil assembly signal
(ignition signal)
Idling Pulse generation
(See WAVEFORM 12)
B93-73 (IGT3) - B93-59 (E1) G - BR No. 3 ignition coil assembly signal
(ignition signal)
Idling Pulse generation
(See WAVEFORM 12)
B93-74 (IGT2) - B93-59 (E1) B - BR No. 2 ignition coil assembly signal
(ignition signal)
Idling Pulse generation
(See WAVEFORM 12)
B93-75 (IGT1) - B93-59 (E1) R - BR No. 1 ignition coil assembly signal
(ignition signal)
Idling Pulse generation
(See WAVEFORM 12)
B93-77 (VCPM) - B93-76 (EPIM) R - BE*1
R - W*2
Power source of manifold absolute pressure sensor Ignition switch ON 4.5 to 5.5 V
B93-78 (PIM) - B93-76 (EPIM) G - BE*1
G - W*2
Manifold absolute pressure sensor signal Ignition switch ON 3.0 to 5.25 V
B93-80 (EV1+) - B93-112 (EV1-) B - R Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See WAVEFORM 13)
B93-81 (VCNE) - B93-59 (E1) P - BR Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
B93-82 (VV1+) - B93-115 (VV1-) B - R Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See WAVEFORM 13)
B93-89 (THEO) - B93-90 (ETHE) W - V Engine oil temperature sensor signal Idling with warm engine 0.3 to 0.85 V
B93-95 (#20) - B93-57 (E01) G - W-B No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See WAVEFORM 14)
B93-96 (#30) - B93-57 (E01) B - W-B No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See WAVEFORM 14)
B93-97 (#40) - B93-57 (E01) W - W-B No. 4 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See WAVEFORM 14)
B93-98 (#10) - B93-57 (E01) L - W-B No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See WAVEFORM 14)
B93-99 (OX1B) - B93-131 (EX1B) W - B Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See WAVEFORM 15)
B93-100 (A1A+) - B93-59 (E1) L - BR Air fuel ratio sensor signal Ignition switch ON 3.3 V*3
B93-101 (VTA2) - B93-133 (ETA) L - L Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
B93-108 (GE01) - Body ground BR - Body ground Shielded ground circuit of throttle actuator Always Below 1 Ω
B93-111 (VCE1) - B93-59 (E1) G - BR Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
B93-114 (NE+) - B93-113 (NE-) GR - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(See WAVEFORM 16)
B93-116 (VCV1) - B93-59 (E1) G - BR Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
B93-120 (THW) - B93-119 (ETHW) GR - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
B93-122 (KNK1) - B93-121 (EKNK) R - G Knock sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See WAVEFORM 17)
B93-132 (A1A-) - B93-59 (E1) Y - BR Air fuel ratio sensor signal Ignition switch ON 2.9 V*3
B93-134 (VCTA) - B93-133 (ETA) Y - L Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
B93-135 (VTA1) - B93-133 (ETA) G - L Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V
B93-136 (SDWN) - B93-59 (E1) G - BR Continuously variable valve lift controller assembly signal Ignition switch ON 7.2 to 10.3 V
B93-137 (VG) - B93-104 (E2G) R - G Mass air flow meter sub-assembly signal Idling, shift lever in P or N (neutral), A/C switch off 0.5 to 3.0 V
B93-138 (THA) - B93-139 (ETHA) W - BR Intake air temperature sensor signal Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V

*1: for CVT Models

*2: for Manual Transaxle Models

*3: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CAN+ and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CAN- and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A210050E11
2.833,2.396 3.167,2.552 0.333,0.156 10 false GND 1.104,2.76 1.771,3.031 0.667,0.271 10 false 2 ms./DIV. 2.229,0.302 2.771,0.594 0.542,0.292 10 false 5 V/DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine


WAVEFORM 4


A283574E01
0.438,0.313 1.167,0.625 0.729,0.313 10 5 V/DIV. 0.448,1.177 0.896,1.458 0.448,0.281 10 GND 1.688,1.885 2.708,2.104 1.021,0.219 10 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A283573E12
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 7


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 9


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 10


A283575E02
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.115 1.021,1.375 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 11


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A299080E15
0.219,1.979 0.552,2.167 0.333,0.188 10 false (IGF) 0.229,1.333 0.563,1.521 0.333,0.188 10 false (IGT) 3.021,1.521 3.354,1.708 0.333,0.188 10 false GND 3.021,2.177 3.354,2.365 0.333,0.188 10 false GND 2.76,0.771 3.354,0.979 0.594,0.208 10 false 2 V/DIV. 1.552,2.594 2.333,2.813 0.781,0.219 10 false 20 ms./DIV. 0.24,1.177 0.573,1.365 0.333,0.188 10 false CH1 0.229,1.823 0.563,2.01 0.333,0.188 10 false CH2

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 13


A255508E20
0.052,0.031 0.656,0.188 0.604,0.156 10 5 V/DIV. 0.167,0.656 0.49,0.823 0.323,0.167 10 CH1 0.156,1.448 0.479,1.615 0.323,0.167 10 CH2 0.094,0.844 0.49,1.052 0.396,0.208 10 (VV1) 0.083,1.604 0.479,1.833 0.396,0.229 10 (EV1) 3.052,0.813 3.396,0.958 0.344,0.146 10 GND 3.052,1.573 3.396,1.719 0.344,0.146 10 GND 1.271,1.865 2.021,2.042 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 14


A287799E02
0.719,1.594 1.177,1.792 0.458,0.198 10 GND 0.396,0.115 1.063,0.344 0.667,0.229 10 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 20 ms./DIV.

No. 1 (to No. 4) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the items O2S B1 S2 show the values input to the ECM from the heated oxygen sensor.



WAVEFORM 16


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.