Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1686  Driver Side Camera Video Sync Signal Malfunction  C1687  Over Current Detected in Driver Side Camera  


DESCRIPTION

These DTCs are stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1686 Driver Side Camera Video Sync Signal Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


C1687 Over Current Detected in Driver Side Camera Side camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH



WIRING DIAGRAM

E334735E13
0.083,2.469 1.531,2.854 1.448,0.385 10 false Side Television Camera Assembly LH 1.823,2.469 3.25,2.844 1.427,0.375 10 false Outer Rear View Mirror Assembly LH 5.656,2.615 7.083,2.99 1.427,0.375 10 false Parking Assist ECU 5.646,2.458 5.958,2.656 0.313,0.198 10 false a1 1.625,0.771 1.781,0.969 0.156,0.198 10 false B 1.625,1.188 1.781,1.385 0.156,0.198 10 false B 1.625,1.604 1.781,1.802 0.156,0.198 10 false B 1.625,2.021 1.781,2.219 0.156,0.198 10 false B 2.635,0.771 3.063,0.969 0.427,0.198 10 false LCB+ 2.646,1.198 3.073,1.396 0.427,0.198 10 false LCV+ 2.667,1.583 3.094,1.781 0.427,0.198 10 false LCV- 2.625,2.021 3.083,2.219 0.458,0.198 10 false LGND 5.823,0.771 6.25,0.969 0.427,0.198 10 false LCB+ 5.823,1.167 6.25,1.365 0.427,0.198 10 false LCV+ 5.823,1.583 6.25,1.781 0.427,0.198 10 false LCV- 5.833,2.031 6.396,2.229 0.563,0.198 10 false LGND 3.198,0.771 3.448,0.99 0.25,0.219 10 false J15 3.24,0.552 3.396,0.75 0.156,0.198 10 false 5 3.25,1 3.406,1.198 0.156,0.198 10 false 6 3.208,1.406 3.521,1.604 0.313,0.198 10 false 14 3.219,1.823 3.531,2.021 0.313,0.198 10 false 13 5.542,0.646 5.74,0.844 0.198,0.198 10 false 12 5.552,1.052 5.75,1.25 0.198,0.198 10 false 10 5.542,1.469 5.75,1.667 0.208,0.198 10 false 11 5.542,1.896 5.781,2.094 0.24,0.198 10 false 24 3.677,2.188 3.833,2.385 0.156,0.198 10 false * 4.125,2.177 4.281,2.375 0.156,0.198 10 false * 4.573,2.177 4.729,2.375 0.156,0.198 10 false * 5.125,2.177 5.281,2.375 0.156,0.198 10 false * 0.344,3.313 2.031,3.51 1.688,0.198 10 false *: Shielded 3.188,1.198 3.438,1.417 0.25,0.219 10 false J15 3.188,1.604 3.438,1.823 0.25,0.219 10 false J15 3.177,2.031 3.427,2.25 0.25,0.219 10 false J15

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTCs C1686 and C1687 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the a1 parking assist ECU connector.


b.

Disconnect the J15 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-12 (LCB+) - J15-5 (LCB+) Always Below 1 Ω
a1-10 (LCV+) - J15-6 (LCV+) Always Below 1 Ω
a1-11 (LCV-) - J15-14 (LCV-) Always Below 1 Ω
a1-24 (LGND) - J15-13 (LGND) Always Below 1 Ω
a1-12 (LCB+) or J15-5 (LCB+) - Body ground Always 10 kΩ or higher
a1-10 (LCV+) or J15-6 (LCV+) - Body ground Always 10 kΩ or higher
a1-11 (LCV-) or J15-14 (LCV-) - Body ground Always 10 kΩ or higher
a1-24 (LGND) or J15-13 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU
a.
E272332C63
1.406,0.208 1.823,0.448 0.417,0.24 1.875,1.375 2.521,1.969 2.521,1.969 2.708,1.969 true 1.844,1.198 0.635,0.781 0.635,0.781 0.51,0.781 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.083,0.698 0.51,0.885 0.427,0.188 10 false LCB+ 2.771,1.875 3.198,2.063 0.427,0.188 10 false LGND 1.542,0.25 2,0.448 0.458,0.198 10 false a1
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-24 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a1-12 (LCB+) - a1-24 (LGND) Engine switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

4.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Remove the parking assist ECU with the connector still connected.

E272333C60
1.281,0.427 1.688,0.646 0.406,0.219 1.625,1.646 1.177,2.438 1.177,2.438 1.052,2.438 true 1.833,1.5 2.24,2.25 2.24,2.25 2.406,2.25 true 3.458,1.823 3.583,2.417 3.583,2.417 3.667,2.417 false 3.563,1.802 4.167,2.417 4.167,2.417 4.333,2.417 false 5.667,1.698 5.5,2.417 5.5,2.417 5.333,2.417 false 5.792,1.646 6,2.417 6,2.417 6.167,2.417 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.417,0.458 1.875,0.656 0.458,0.198 10 false a1 0.604,2.365 1.063,2.563 0.458,0.198 10 false LGND 2.479,2.167 2.938,2.365 0.458,0.198 10 false LCV+ 2.729,1.302 3.188,1.5 0.458,0.198 10 false GND 4.865,1.302 5.323,1.5 0.458,0.198 10 false GND 3.021,0.406 3.333,0.604 0.313,0.198 10 false *b 5.125,0.406 5.438,0.604 0.313,0.198 10 false *c 3.719,2.354 4.031,2.552 0.313,0.198 10 false *d 5.167,2.344 5.479,2.542 0.313,0.198 10 false *d 4.396,2.344 4.708,2.542 0.313,0.198 10 false *e 6.208,2.333 6.521,2.531 0.313,0.198 10 false *e
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Measure the waveform of the side television camera assembly LH using an oscilloscope.

HINT:
·

A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the side television camera assembly.



Measurement Condition
Item Content
Tester Connection a1-10 (LCV+) - a1-24 (LGND)
Tool Setting 200 mV/DIV., 50 μs/DIV.
Condition
·

Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image


·

Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen



OK:

Waveform is as shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH
5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTCs C1686 and C1687 are not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH