Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C306841C03
0.198,0.146 0.51,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND2) Pump motor ground
2 - (Not used)
3 - (Not used)
4 - (Not used)
5 (STP2) Stop light switch assembly input
6 - (Not used)
7 - (Not used)
8 - (Not used)
9 - (Not used)
10 (CANL) CAN communication line L
11 (EXI3)*1 Back-up light switch assembly input
12 (IG1) ECU power supply input
13 (BM) Motor relay power supply
14 (SP1) Speed signal output for speedometer
15 (RR-) Rear wheel speed RH (-) signal input
16 (RR+) Rear wheel speed RH (+) power supply output
17 (FL-) Front wheel speed LH (-) signal input
18 (FL+) Front wheel speed LH (+) power supply output
19 - (Not used)
20 - (Not used)
21 - (Not used)
22 (CANH) CAN communication line H
23 - (Not used)
24 - (Not used)
25 (GND1) Skid control ECU (Brake actuator assembly) ground
26 (STPO) Stop light control relay output
27 (HDCS)*2 Downhill assist control switch input
28 (RL-) Rear wheel speed LH (-) signal input
29 (RL+) Rear wheel speed LH (+) power supply output
30 (FR-) Front wheel speed RH (-) signal input
31 (FR+) Front wheel speed RH (+) power supply output
32 - (Not used)
33 (CSW) VSC OFF switch (Telltale light assembly) input
34 - (Not used)
35 (STP) Stop light switch assembly input
36 - (Not used)
37 - (Not used)
38 (+BS) Solenoid relay power supply

*1: for Manual Transaxle

*2: w/ Downhill Assist Control



TERMINAL INSPECTION


a.

Disconnect the A100skid control ECU (brake actuator assembly) connector and measure the voltage or resistance on the wire harness side.

C306842C29
1.667,1.167 2.104,1.469 0.438,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.74,1.229 2.198,1.427 0.458,0.198 10 false A100
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-1 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A100-5 (STP2) - Body ground LG - Body ground Stop light signal input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A100-11 (EXI3) - Body ground*1 R - Body ground Back-up light switch assembly input Shift lever not in R → Shift lever in R Below 1.5 V → 8 to 14 V
A100-12 (IG1) - Body ground L - Body ground ECU power supply input Ignition switch ON 10.5 to 16 V*3
11 to 14 V*4
A100-13 (BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A100-14 (SP1) - Body ground V - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A100-25 (GND1) - Body ground W-B - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A100-26 (STPO) - Body ground W - Body ground Stop light control relay output Ignition switch ON 11 to 14 V
A100-27 (HDCS) - Body ground*2 Y - Body ground Downhill assist control switch input Downhill assist control switch on → off Below 1 Ω → 10 kΩ or higher
A100-33 (CSW) - Body ground L - Body ground VSC OFF switch (Telltale light assembly) input VSC OFF switch (telltale light assembly) pressed and held → released Below 1 Ω → 10 kΩ or higher
A100-35 (STP) - Body ground L - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A100-38 (+BS) - Body ground W - Body ground Solenoid relay power supply Always 11 to 14 V

*1: for Manual Transaxle

*2: w/ Downhill Assist Control

*3: w/ Stop and Start System

*4: w/o Stop and Start System