Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U0230  Lost Communication with Rear Gate Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0230 Lost Communication with Rear Gate Module There is no communication from the multiplex network door ECU.
·

Power source or inside multiplex network door ECU

·

Multiplex network door ECU CAN branch wire or connector

·

Multiplex network door ECU


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C280381E57
5.198,6 6.958,6.281 1.76,0.281 10 false Multiplex Network Door ECU 5.646,5.073 7,5.458 1.354,0.385 10 false GND 5.646,4.25 7,4.635 1.354,0.385 10 false IG 5.646,3.438 7,3.823 1.354,0.385 10 false B 5.646,2.583 7,2.969 1.354,0.385 10 false ECUB 5.646,1.438 7,1.823 1.354,0.385 10 false CANN 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANP 1.677,0.698 3.031,1.083 1.354,0.385 10 false 9 1.667,1.271 3.021,1.656 1.354,0.385 10 false 20 0.438,1.771 1.792,2.156 1.354,0.385 10 false N39 0.438,1.938 2.813,2.219 2.375,0.281 10 false No. 5 CAN Junction Connector 2.115,2.563 3.469,2.948 1.354,0.385 10 false from Battery 1.604,4.208 2.958,4.594 1.354,0.385 10 false from IG1 NO.1 Relay 3.802,4.073 5.156,4.458 1.354,0.385 10 false ECU-IG NO.2 4.104,3.24 5.021,3.656 0.917,0.417 10 false PBD 5.156,2.583 6.073,3 0.917,0.417 10 false U29 5.146,3.406 6.063,3.823 0.917,0.417 10 false U30 5.146,4.229 6.063,4.646 0.917,0.417 10 false U29 5.146,5.052 6.063,5.469 0.917,0.417 10 false U30 5.146,1.406 6.063,1.823 0.917,0.417 10 false U29 5.146,0.823 6.063,1.24 0.917,0.417 10 false U29 5.188,1.156 6.542,1.542 1.354,0.385 10 false 40 5.188,0.563 6.542,0.948 1.354,0.385 10 false 39 5.188,2.333 6.542,2.719 1.354,0.385 10 false 20 5.219,3.167 6.573,3.552 1.354,0.385 10 false 1 5.188,3.99 6.542,4.375 1.354,0.385 10 false 18 5.188,4.802 6.542,5.188 1.354,0.385 10 false 10 3.885,2.427 5.24,2.813 1.354,0.385 10 false ECU-B NO.1 2.104,3.396 3.458,3.781 1.354,0.385 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
HINT:

If DTC U1002 is output from gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR ECU CAN BRANCH WIRE)

B

GO TO GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR ECU CAN BRANCH WIRE)
a.
C317101C07
1.49,0.188 1.958,0.448 0.469,0.26 2.604,1.948 2.76,1.948 2.76,1.948 2.906,1.292 true 2.292,1.688 2.448,1.688 2.448,1.688 2.771,1.281 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.583,0.219 2.042,0.417 0.458,0.198 10 false U29 1.854,1.552 2.469,1.75 0.615,0.198 10 false CANP 2.177,1.833 2.792,2.042 0.615,0.208 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U29-39 (CANP) - U29-40 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTIPLEX NETWORK DOOR ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)
a.
C325480C20
1.5,0.375 1.958,0.615 0.458,0.24 1.417,2.302 1.917,2.552 0.5,0.25 0.313,2.719 0.469,2.719 0.469,2.719 1.021,3.104 true 2.958,0.729 2.813,0.729 2.813,0.729 2.646,1.24 true 2.813,3.875 2.667,3.875 2.667,3.875 2.292,3.583 true 2.302,1.927 2.49,1.927 2.49,1.927 2.906,1.302 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.594,0.396 2.052,0.594 0.458,0.198 10 false U29 1.521,2.333 1.979,2.531 0.458,0.198 10 false U30 1.865,1.854 2.344,2.042 0.479,0.188 10 false ECUB 2.875,3.771 3.271,3.99 0.396,0.219 10 false GND 3.021,0.615 3.302,0.885 0.281,0.271 10 false IG 0.125,2.635 0.521,2.854 0.396,0.219 10 false B
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the multiplex network door ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U29-20 (ECUB) - Body ground Always 11 to 14 V
U30-1 (B) - Body ground Always 11 to 14 V
U29-18 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U30-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR