HANDLING OF A VEHICLE THAT HAS BEEN DAMAGED IN A COLLISION
Refer to the TOYOTA Repair Manual for the SRS airbag system inspection procedures.
If impacts are likely to occur to the front airbag sensors, floor side airbag sensors, No. 2 side airbag sensor assemblies, side airbag pressure sensors or airbag sensor assembly remove each sensor as necessary beforehand.
Do not allow the front airbag sensors, floor side airbag sensors, No. 2 side airbag sensor assemblies, side airbag pressure sensors or airbag sensor assembly to become heated to high temperatures.
Check the wire harnesses and connectors for damage and/or melting, as some areas of the airbags and seat belt pretensioners may heat up to several hundred degrees when they operate.
PRECAUTIONS FOR USING ELECTRIC WELDER
Check the Diagnostic Trouble Codes (DTCs).
If one or more DTCs are displayed:
Disconnect the negative (-) terminal cable from the battery.
Disconnect all the malfunctioning circuit connectors.
Disconnect the airbag ECU assembly connector.
If DTCs are NOT displayed:
Inspect for damage to the electric wiring harnesses and connectors.
Disconnect the negative (-) terminal cable from the battery.
Disconnect the airbag ECU assembly connector.
DOOR SIDE AIRBAG SENSOR (PRESSURE SENSOR) DESCRIPTION
A door side airbag sensor is installed to the center of the front door.
The sensor detects pressure changes between the door outer and door inner according to deformation of the door panel.
The door side airbag sensor (pressure sensor) and side airbag sensor (G sensor) perform ignition judgement using AND circuits for improved side airbag deployment.
PRECAUTIONS WHEN REPAIRING BODY
Ensure the front door outer and door inner are airtight.
Apply masking tape to the door side airbag sensor to prevent the entry of foreign matter.
Decreased airtightness between the front door outer and door inner may affect detection performance.
Use large, clearly visible pieces of masking tape to prevent tape from being left on the sensor after the procedure.
| PRECAUTION | INSPECTION/PROCEDURE | ||
|---|---|---|---|
| Airtightness between door outer and inner | Parts important for airtightness | Service hole cover | ·
If there are gaps or cracks in the seal surface (A) or clip installation area, replace it with a new one. |
| Speaker | ·
If there are gaps in the seal surface or the cone is damaged, replace it with a new one. |
||
| Belt moulding | ·
If there are gaps in the seal surface or the lip is worn or cracked, replace it with a new one. ·
Do not reuse a removed belt moulding. |
||
| Weatherstrip INN | ·
If there are gaps in the seal surface or the lip is worn or cracked, replace it with a new one. |
||
| Front door | ·
If a door panel has holes or cracks, repair or replace it. (If damage has spread to the impact beam, replace it with a new one) ·
If the installation areas of parts important for airtightness are damaged or deformed, repair or replace them. |
||
| Prevention of foreign matter entry into sensor | Painting and grinding with service hole cover removed | ·
Before performing work, apply masking tape to the air inlet (B) of the door side airbag sensor to prevent the entry of foreign matter. (such as paint, dust and pieces of glass) ·
Keep the spray or vacuum cleaner nozzle away from the sensor. Otherwise, it may be damaged. |
|
| Applying anti-rust agents (wax) | |||
| Removing pieces of glass from inside door panel | |||
|
Seal surface |
| *1 | Door side airbag sensor |
| *2 | Air inlet |
LOCATION OF PARTS IMPORTANT FOR AIRTIGHTNESS
| *A | w/o Woofer | *B | w/ Woofer |
| *1 | FRONT DOOR FRONT BELT SEAL LH | *2 | FRONT DOOR INNER GLASS WEATHERSTRIP LH |
| *3 | FRONT DOOR REAR BELT SEAL LH | *4 | FRONT DOOR SERVICE HOLE COVER LH |
| *5 | FRONT NO. 1 SPEAKER ASSEMBLY | *6 | OUTER MIRROR INSTALL HOLE COVER LH |
| *7 | OUTER REAR VIEW MIRROR ASSEMBLY LH | *8 | SIDE AIRBAG PRESSURE SENSOR LH |
| *9 | RIVET | *10 | SERVICE HOLE COVER CLIP |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *1 | DOOR FRAME GARNISH LH | *2 | FRONT DOOR BELT MOULDING LH |
| *3 | FRONT DOOR FIX WINDOW GLASS LH | *4 | FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH |
| *5 | FRONT DOOR GLASS RUN LH | *6 | FRONT DOOR GLASS SUB-ASSEMBLY LH |
| *7 | FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH | *8 | FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
| *9 | POWER WINDOW REGULATOR MOTOR ASSEMBLY LH | *10 | HOLE PLUG |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
PARTS LOCATION (for HV Model with Occupant Classification System)
| *1 | FRONT AIRBAG SENSOR LH | *2 | FRONT AIRBAG SENSOR RH |
| *3 | FLOOR SIDE AIRBAG SENSOR LH | *4 | FLOOR SIDE AIRBAG SENSOR RH |
| *5 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH | *6 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH |
| *7 | SIDE AIRBAG PRESSURE SENSOR LH | *8 | SIDE AIRBAG PRESSURE SENSOR RH |
| *1 | CURTAIN SHIELD AIRBAG ASSEMBLY LH | *2 | CURTAIN SHIELD AIRBAG ASSEMBLY RH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY LH | *4 | FRONT SEAT AIRBAG ASSEMBLY RH |
| *5 | FRONT SEAT OUTER BELT ASSEMBLY LH
- PRETENSIONER |
*6 | FRONT SEAT OUTER BELT ASSEMBLY RH
- PRETENSIONER |
| *7 | REAR SEAT OUTER BELT ASSEMBLY LH | *8 | REAR SEAT OUTER BELT ASSEMBLY RH |
| *1 | AIRBAG SENSOR ASSEMBLY | *2 | SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
| *3 | HORN BUTTON ASSEMBLY | *4 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| *5 | INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY | *6 | COMBINATION METER ASSEMBLY |
| *7 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- A/BAG-IG2 FUSE |
*8 | TELLTALE LIGHT ASSEMBLY
- PASSENGER AIRBAG ON/OFF INDICATOR |
| *9 | HYBRID VEHICLE CONTROL ECU | *10 | DLC3 |
| *1 | OCCUPANT DETECTION ECU | *2 | FRONT SEAT CUSHION AIRBAG ASSEMBLY RH |
| *3 | FRONT SEAT INNER BELT ASSEMBLY LH
- BUCKLE SWITCH |
*4 | FRONT SEAT INNER BELT ASSEMBLY RH |
| *5 | FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR) | - | - |
PARTS LOCATION (for Gasoline Model with Occupant Classification System)
| *1 | FRONT AIRBAG SENSOR LH | *2 | FRONT AIRBAG SENSOR RH |
| *3 | FLOOR SIDE AIRBAG SENSOR LH | *4 | FLOOR SIDE AIRBAG SENSOR RH |
| *5 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH | *6 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH |
| *7 | SIDE AIRBAG PRESSURE SENSOR LH | *8 | SIDE AIRBAG PRESSURE SENSOR RH |
| *9 | ECM | - | - |
| *1 | CURTAIN SHIELD AIRBAG ASSEMBLY LH | *2 | CURTAIN SHIELD AIRBAG ASSEMBLY RH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY LH | *4 | FRONT SEAT AIRBAG ASSEMBLY RH |
| *5 | FRONT SEAT OUTER BELT ASSEMBLY LH
- PRETENSIONER |
*6 | FRONT SEAT OUTER BELT ASSEMBLY RH
- PRETENSIONER |
| *7 | REAR SEAT OUTER BELT ASSEMBLY LH | *8 | REAR SEAT OUTER BELT ASSEMBLY RH |
| *1 | AIRBAG SENSOR ASSEMBLY | *2 | SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
| *3 | HORN BUTTON ASSEMBLY | *4 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| *5 | INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY | *6 | COMBINATION METER ASSEMBLY |
| *7 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- A/BAG-IG2 FUSE |
*8 | TELLTALE LIGHT ASSEMBLY
- PASSENGER AIRBAG ON/OFF INDICATOR |
| *9 | DLC3 | - | - |
| *1 | OCCUPANT DETECTION ECU | *2 | FRONT SEAT CUSHION AIRBAG ASSEMBLY RH |
| *3 | FRONT SEAT INNER BELT ASSEMBLY LH
- BUCKLE SWITCH |
*4 | FRONT SEAT INNER BELT ASSEMBLY RH |
| *5 | FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR) | - | - |
PARTS LOCATION (w/o Occupant Classification System)
| *A | for Gasoline Model | - | - |
| *1 | FRONT AIRBAG SENSOR LH | *2 | FRONT AIRBAG SENSOR RH |
| *3 | FLOOR SIDE AIRBAG SENSOR LH | *4 | FLOOR SIDE AIRBAG SENSOR RH |
| *5 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH | *6 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH |
| *7 | SIDE AIRBAG PRESSURE SENSOR LH | *8 | SIDE AIRBAG PRESSURE SENSOR RH |
| *9 | ECM | - | - |
| *A | w/ Rear Pretensioner | - | - |
| *1 | CURTAIN SHIELD AIRBAG ASSEMBLY LH | *2 | CURTAIN SHIELD AIRBAG ASSEMBLY RH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY LH | *4 | FRONT SEAT AIRBAG ASSEMBLY RH |
| *5 | FRONT SEAT OUTER BELT ASSEMBLY LH
- PRETENSIONER |
*6 | FRONT SEAT OUTER BELT ASSEMBLY RH
- PRETENSIONER |
| *7 | REAR SEAT OUTER BELT ASSEMBLY LH
- PRETENSIONER |
*8 | REAR SEAT OUTER BELT ASSEMBLY RH
- PRETENSIONER |
| *A | for RHD | *B | w/ Airbag Cutoff Switch |
| *C | for HV Model | *D | w/ Telematics System |
| *1 | AIRBAG SENSOR ASSEMBLY | *2 | SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
| *3 | HORN BUTTON ASSEMBLY | *4 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| *5 | INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY | *6 | AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY |
| *7 | COMBINATION METER ASSEMBLY | *8 | TELLTALE LIGHT ASSEMBLY
- PASSENGER AIRBAG ON/OFF INDICATOR |
| *9 | HYBRID VEHICLE CONTROL ECU | *10 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- A/BAG-IG2 FUSE |
| *11 | DLC3 | *12 | TELEMATICS TRANSCEIVER |
| *A | for LHD | *B | w/ Airbag Cutoff Switch |
| *C | for HV Model | *D | except Manual Transaxle |
| *E | for Manual Transaxle | *F | w/ Telematics System |
| *1 | AIRBAG SENSOR ASSEMBLY | *2 | SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
| *3 | HORN BUTTON ASSEMBLY | *4 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| *5 | INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY | *6 | AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY |
| *7 | COMBINATION METER ASSEMBLY | *8 | TELLTALE LIGHT ASSEMBLY
- PASSENGER AIRBAG ON/OFF INDICATOR |
| *9 | HYBRID VEHICLE CONTROL ECU | *10 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- A/BAG-IG2 FUSE |
| *11 | DLC3 | *12 | TELEMATICS TRANSCEIVER |