Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2018.10–2019.09
BM3620E _V1 General _078136 INTRODUCTION _0379061 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed
Front wheel alignment adjustment
for HV Model:
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions



Necessary Procedures After Procedure Performed (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed
Front wheel alignment adjustment
for Gasoline Model:
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates



MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C404817N01
0.833,1.115 0.99,1.313 0.156,0.198 10 false A 2.396,1.229 2.552,1.427 0.156,0.198 10 false B 0.844,3.99 1,4.188 0.156,0.198 10 false C 2.354,4.042 2.51,4.24 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center.


B: Ground clearance of center of bolt head of front lower No. 2 suspension arm sub-assembly and front suspension crossmember sub-assembly.


C: Ground clearance of rear wheel center.


D: Ground clearance of center of tip of threaded portion of rear lower No. 2 suspension arm assembly and rear suspension member sub-assembly.


Vehicle Height (Unloaded Vehicle):
Tire Size Front A - B Rear C - D

*1: for Saudi Arabia (for 4WD)

225/65R17 117 mm (4.61 in.) *1 41 mm (1.61 in.) *1
133 mm (5.24 in.) 60 mm (2.36 in.)
225/60R18 117 mm (4.61 in.) *1 41 mm (1.61 in.) *1
133 mm (5.24 in.) 60 mm (2.36 in.)
235/55R19 117 mm (4.61 in.) *1 41 mm (1.61 in.) *1
133 mm (5.24 in.) 60 mm (2.36 in.)




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: for Saudi Arabia (for 4WD)

225/65R17 -0°20' +/-45' (-0.33° +/-0.75°) 0°45' (0.75°) or less
-0°05' +/-45' (-0.08° +/-0.75°) *1
225/60R18 -0°20' +/-45' (-0.33° +/-0.75°)
-0°05' +/-45' (-0.08° +/-0.75°) *1
235/55R19 -0°20' +/-45' (-0.33° +/-0.75°)
-0°05' +/-45' (-0.08° +/-0.75°) *1


Caster (Unloaded Vehicle):
Tire Size Caster Inclination Right-left Difference

*1: for Saudi Arabia (for 4WD)

225/65R17 5°00' +/-45' (5.00° +/-0.75°) 0°45' (0.75°) or less
4°55' +/-45' (4.92° +/-0.75°) *1
225/60R18 5°00' +/-45' (5.00° +/-0.75°)
4°55' +/-45' (4.92° +/-0.75°) *1
235/55R19 5°00' +/-45' (5.00° +/-0.75°)
4°55' +/-45' (4.92° +/-0.75°) *1


Steering Axis Inclination (Unloaded Vehicle):
Tire Size Steering Axis Inclination Reference

*1: for Saudi Arabia (for 4WD)

225/65R17 12°30' (12.50°)
12°05' (12.08°) *1
225/60R18 12°30' (12.50°)
12°05' (12.08°) *1
235/55R19 12°30' (12.50°)
12°05' (12.08°) *1




INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Automatic Transaxle, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


e.

Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



g.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition

*1: for Saudi Arabia (for 4WD)

225/65R17 C + D: 0°13' +/- 0°10' (0.22° +/- 0.17°)
B - A: 2.5 +/-2.0 mm (0.10 +/-0.08 in.)
C + D: 0°12' +/- 0°10' (0.20° +/- 0.17°)*1
B - A: 2.3 +/-2.0 mm (0.09 +/-0.08 in.) *1
225/60R18 C + D: 0°13' +/- 0°10' (0.22° +/- 0.17°)
B - A: 2.5 +/-2.0 mm (0.10 +/-0.08 in.)
C + D: 0°12' +/- 0°10' (0.20 +/- 0.17°) *1
B - A: 2.3 +/-2.0 mm (0.09 +/-0.08 in.) *1
235/55R19 C + D: 0°13' +/- 0°10' (0.22° +/- 0.17°)
B - A: 2.6 +/-2.0 mm (0.10 +/-0.08 in.)
C + D: 0°12' +/- 0°10' (0.19° +/- 0.17°) *1
B - A: 2.3 +/-2.0 mm (0.09 +/-0.08 in.) *1


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.



INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Tire Size Inside Wheel Outside Wheel

*1: for Saudi Arabia (for 4WD)

225/65R17 37°15' (35°15' to 39°15')
(37.25° (35.25° to 39.25°))
32°10' (32.17°)
37°40' (35°40' to 39°40') *1
(37.67° (35.67° to 39.67°))*1
32°25' (32.42°) *1
225/60R18 37°15' (35°15' to 39°15')
(37.25° (35.25° to 39.25°))
32°10' (32.17°)
37°40' (35°40' to 39°40') *1
(37.67° (35.67° to 39.67°))*1
32°25' (32.42°) *1
235/55R19 35°15' (33°15' to 37°15')
(35.25° (33.25° to 37.25°))
30°50' (30.83°)
35°40' (33°40' to 37°40') *1
(35.67° (33.67° to 37.67°)) *1
31°05' (31.08°) *1


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.




INSPECT CAMBER (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: for Saudi Arabia (for 4WD)

225/65R17 -1°05' +/-45' (-1.08° +/-0.75°) 0°45' (0.75°) or less
-1°00' +/-45' (-1.00° +/-0.75°) *1
225/60R18 -1°05' +/-45' (-1.08° +/-0.75°)
-1°00' +/-45' (-1.00° +/-0.75°) *1
235/55R19 -1°05' +/-45' (-1.08° +/-0.75°)
-1°00' +/-45' (-1.00° +/-0.75°) *1


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Automatic transaxle, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


e.

Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



g.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition

*1: for Saudi Arabia (for 4WD)

225/65R17 C + D: 0°14' +/- 0°10' (0.23° +/- 0.17°)
B - A: 2.6 +/-2.0 mm (0.10 +/-0.08 in.)
C + D: 0°02' +/- 0°10' (0.03° +/- 0.17°) *1
B-A: 0.3 +/-2.0 mm (0.01 +/-0.08 in.) *1
225/60R18 C + D: 0°13' +/- 0°10' (0.22° +/- 0.17°)
B - A: 2.6 +/-2.0 mm (0.10 +/-0.08 in.)
C + D: 0°02' +/- 0°10' (0.03° +/- 0.17°) *1
B-A: 0.3 +/-2.0 mm (0.01 +/-0.08 in.) *1
235/55R19 C + D: 0°14' +/- 0°10' (0.23° +/- 0.17°)
B - A: 2.7 +/-2.0 mm (0.11 +/-0.08 in.)
C + D: 0°02' +/- 0°10' (0.03° +/- 0.17°) *1
B-A: 0.3 +/-2.0 mm (0.01 +/-0.08 in.) *1


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rear suspension toe adjust cam sub-assembly.