Home › Vehicle Exterior › BODY DIMENSIONS › ENGINE COMPARTMENT
BM3620E _01 Vehicle Exterior _078596 BODY DIMENSIONS _0381284 ENGINE COMPARTMENT F

BODY DIMENSIONS  ENGINE COMPARTMENT  POINT-TO-POINT DISTANCE  


HINT:
·

Point Q, q on the vehicle are asymmetrical.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Measuring Point Name
Symbol Name Hole Diameter
mm (in.)
A Cowl Top Inner Panel Center Mark -
B, b Hood Hinge Installation Nut M8 (0.31)
C, c Radiator Upper Support Standard Hole φ10 (0.39)
D, d Radiator Upper Support Standard Hole φ10 (0.39)
E, e Radiator Support Upper Brace Standard Hole φ10 (0.39)
F, f Radiator Support Upper Brace Standard Hole φ11 (0.43)
G, g Front Bumper Reinforcement Installation Nut M10 (0.39)
H, h Front Fender Apron Upper Gusset Standard Hole φ15 (0.59)
J, j Radiator Support Upper Center Repair Standard Hole φ7 (0.28)
K, k Radiator Support Upper Center Installation Nut M6 (0.24)
L, l Radiator Support Upper Center Installation Nut M6 (0.24)
M, m Front Side Member To Floor Plate Standard Hole φ10 (0.39)
N, n Front Bumper Reinforcement Installation Nut M10 (0.39)
O, o Front Suspension Installation Hole (Upper Face) φ12.5 (0.49)
P, p Front Side Member Standard Hole φ15 (0.59)
Q, q M8 Nut M8 (0.31)
R, r Front Suspension Installation Hole (Lower Face) φ12.5 (0.49)
S, s Speed Sensor Installation Nut M6 (0.24)

K143695

Symmetric distance
K143696

Asymmetric distance

K160148C04
4.083,7.927 4.396,8.083 0.313,0.156 10 false *a 0.083,8.625 0.396,8.781 0.313,0.156 10 false *b 0.719,7.938 1.031,8.094 0.313,0.156 10 false *W
*a Height from Imaginary Datum Line *b mm
(in.)
*W Width distance - -


K160149C01
0.083,8.615 0.396,8.771 0.313,0.156 10 false *a 0.375,6.333 0.688,6.49 0.313,0.156 10 false *W 0.385,7.167 0.698,7.323 0.313,0.156 10 false *L 0.375,8.042 0.688,8.198 0.313,0.156 10 false *X
*a mm
(in.)
- -
*W Width distance *L Length distance
*X Diagonal distance - -


Measuring Point Name
Symbol Name Hole Diameter
mm (in.)
A Cowl Top Inner Panel Center Mark -
B, b Front Fender Installation Nut M6 (0.24)
C, c Front Fender Installation Nut M6 (0.24)
D, d Headlight Installation Hole 9X9
(0.35X0.35)
E, e Radiator Support Upper Center Installation Nut M6 (0.24)
F, f Radiator Support Upper Center Installation Nut M6 (0.24)
G, g Headlight Installation Hole 9X9
(0.35X0.35)
H, h Hood Lock Support Standard Hole φ10 (0.39)
J, j Front Fender Installation Nut M6 (0.24)
K, k Front Fender Installation Nut M6 (0.24)

K149626C01
0.083,8.594 0.396,8.75 0.313,0.156 10 false *a
*a mm
(in.)
- -
*W Width distance *L Length distance
*X Diagonal distance - -