Home › Vehicle Exterior › BODY PANEL › REAR DOOR OUTER PANEL
BM3620E _01 Vehicle Exterior _077725 BODY PANEL _0383644 REAR DOOR OUTER PANEL F

BODY PANEL  REAR DOOR OUTER PANEL  ASSEMBLY REPLACEMENT  


K149462

REMOVAL


Symbol Meaning
K108818

Remove Weld Points

a.

Before removing the outer panel, mark the installation position with tape.

HINT:

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.


K148842C01
2.083,0.75 2.25,0.75 2.25,0.75 2.542,0.958 false 1.896,0.656 2.208,0.813 0.313,0.156 10 false *a 3.01,1.125 3.323,1.281 0.313,0.156 10 false *b
*a Positioning Tape *b Installation Position



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K150531C01
0,0 0,0 false
K108837

Adhesive - -



c.

After grinding off the hemming location, remove the outer panel.

K148843C01
6.333,2.667 6.167,2.667 6.167,2.667 6.094,2.323 false 5.958,0.417 6.271,0.573 0.313,0.156 10 false *a 6.396,2.583 6.708,2.74 0.313,0.156 10 false *b
*a Disc Sander *b Hemming Location




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108833

Spot MIG Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

NOTICE:

Do not close the drain hole.


HINT:

Apply enough adhesive to the panels.


K150532C01
6.125,3 6.438,3.156 0.313,0.156 10 false *a
*a Drain Hole - -
K108837

Adhesive - -



c.

Before temporarily installing the new parts, apply body sealer to the backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement to make contact.


K150534


d.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K148844C02
1.438,0.99 1.25,0.667 1.25,0.667 1.083,0.667 false 5.167,6.833 5.333,6.833 5.333,6.833 5.542,6.49 false 6.063,5.781 6.25,5.5 6.25,5.5 6.417,5.5 false 6.5,6.583 6.333,6.583 6.333,6.583 6.208,6.281 false 3.042,2.656 3.302,3.021 3.302,3.021 3.469,3.021 false 0.896,0.594 1.208,0.75 0.313,0.156 10 false *a 6.479,5.427 6.792,5.583 0.313,0.156 10 false *b 6.563,6.5 6.875,6.656 0.313,0.156 10 false *c 4.979,6.76 5.292,6.917 0.313,0.156 10 false *d 3.51,2.958 3.823,3.115 0.313,0.156 10 false *1
*1 REAR DOOR PANEL OUTER - -
*a Positioning Tape *b Cloth Tape
*c Dolly *d Wooden Hammer



e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.