Home › Vehicle Exterior › BODY PANEL › REAR FLOOR UPPER CENTER CROSSMEMBER
BM3620E _01 Vehicle Exterior _077725 BODY PANEL _0383656 REAR FLOOR UPPER CENTER CROSSMEMBER F

BODY PANEL  REAR FLOOR UPPER CENTER CROSSMEMBER  ASSEMBLY REPLACEMENT  


K149476

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K150010C01
0,0 0,0 false
K108837

Adhesive - -



b.

After removing the A, remove the B.

K149120C01
0.281,5.677 3.563,8.656 3.281,2.979 3.563,5.677 6.844,8.656 3.281,2.979 4,8 4.167,8 4.167,8 5.083,7.5 false 3.354,2.656 3.167,1.75 3.167,1.75 3,1.75 false 2.073,7.5 2.823,8 2.823,8 2.99,8 false 0.5,5.844 0.813,6 0.313,0.156 10 false *A 3.75,5.833 4.063,5.99 0.313,0.156 10 false *B 2.875,1.667 3.031,1.865 0.156,0.198 10 false A 3.885,7.917 4.042,8.115 0.156,0.198 10 false B 3.042,7.927 3.198,8.125 0.156,0.198 10 false B
*A LH Side *B RH Side




INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Remove A from the new parts.

K149157C01
3.604,4.125 3.417,3.5 3.417,3.5 3.25,3.5 false 3.844,5.25 3.698,5.25 3.698,5.25 3.292,4.594 false 3.094,3.427 3.406,3.583 0.313,0.156 10 false *1 3.885,5.156 4.042,5.354 0.156,0.198 10 false A
*1 REAR FLOOR PARTITION PANEL SUB-ASSEMBLY - -



c.

Weld the A to the vehicle side.

K149122C01
3.583,0.25 7,3.583 3.417,3.333 0.167,0.25 3.583,3.583 3.417,3.333 1.979,2.083 2.833,1.5 2.833,1.5 3,1.5 false 5.385,2.021 6.167,1.5 6.167,1.5 6.333,1.5 false 0.354,0.427 0.667,0.583 0.313,0.156 10 false *A 3.75,0.427 4.063,0.583 0.313,0.156 10 false *B 5.771,0.625 6.083,0.781 0.313,0.156 10 false *a 1.083,0.646 1.396,0.802 0.313,0.156 10 false *a 3.083,1.417 3.24,1.615 0.156,0.198 10 false A 6.427,1.417 6.583,1.615 0.156,0.198 10 false A
*A LH Side *B RH Side
*a 25 mm (0.98 in.) - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K150010C02
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the A to the vehicle side.

K149121N01
2.917,2.25 3.083,2.25 3.083,2.25 3.292,3.146 false 2.781,2.177 2.938,2.375 0.156,0.198 10 false A


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.