Home › Vehicle Exterior › BODY PANEL › ROOF PANEL(for Sliding Roof)
BM3620E _01 Vehicle Exterior _077725 BODY PANEL _0383662 ROOF PANEL(for Sliding Roof) F

BODY PANEL  ROOF PANEL(for Sliding Roof)  ASSEMBLY REPLACEMENT  


K149481

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points

a.

If reusing the roof panel reinforcement, trim the hemming location using a disc sander, etc.


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K149145C01
0,0 0,0 false
*1 ROOF PANEL *2 ROOF PANEL REINFORCEMENT NO.2
*3 ROOF PANEL REINFORCEMENT NO.4 *4 ROOF PANEL REINFORCEMENT NO.5
*a Wooden Hammer *b Dolly
*c Cloth Tape - -
K108837

Adhesive - -


K149140



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, apply body sealer and adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the roof panel reinforcement.

HINT:

Apply enough body sealer and adhesive to the panels.


K149146C03
2.25,1 2.083,1 2.083,1 1.844,1.896 false 3.75,1 3.583,1 3.583,1 3.417,1.667 false 4.083,1.698 4.26,1 4.26,1 4.427,1 false 4.802,1.698 4.917,1 4.917,1 5.083,1 false 2.271,0.917 2.583,1.073 0.313,0.156 10 false *1 3.771,0.927 4.083,1.083 0.313,0.156 10 false *2 5.104,0.927 5.417,1.083 0.313,0.156 10 false *3 4.448,0.938 4.76,1.094 0.313,0.156 10 false *2
*1 ROOF PANEL REINFORCEMENT NO.2 *2 ROOF PANEL REINFORCEMENT NO.4
*3 ROOF PANEL REINFORCEMENT NO.5 - -
K108837

Adhesive - -



d.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.



e.

Before temporarily installing the new parts, weld the roof panel, roof panel reinforcement no.2, roof panel reinforcement no.4 and roof panel reinforcement no.5 with the standard number of welding points.

K149147C02
0.75,1.75 0.917,1.75 0.917,1.75 1.146,1.427 false 2.104,1.219 2.083,0.667 2.083,0.667 1.917,0.667 false 3.344,1.271 3.167,0.667 3.167,0.667 3,0.667 false 3.75,0.667 3.917,0.667 3.917,0.667 4,1.354 false 4.5,0.667 4.667,0.667 4.667,0.667 4.75,1.26 false 2,4.417 2.167,4.417 2.167,4.417 2.531,4.604 false 2.646,4.438 2.417,4 2.417,4 2.583,4 false 2,5.417 2.167,5.417 2.167,5.417 2.365,5.25 false 0.583,1.656 0.896,1.813 0.313,0.156 10 false *1 1.76,0.583 2.073,0.74 0.313,0.156 10 false *2 4.354,0.583 4.667,0.74 0.313,0.156 10 false *4 1.844,5.323 2.156,5.479 0.313,0.156 10 false *a 2.604,3.917 2.917,4.073 0.313,0.156 10 false *b 1.844,4.313 2.156,4.469 0.313,0.156 10 false *c 2.854,0.583 3.167,0.74 0.313,0.156 10 false *3 3.604,0.583 3.917,0.74 0.313,0.156 10 false *3
*a Disc Sander - -
K108837

Adhesive - -



f.

Before temporarily installing the new parts, apply body sealer to the windshield header panel sub-assembly and roof panel reinforcement sub-assembly rear.

HINT:

Apply enough body sealer to the panels.


K149161C01
0.667,2.833 0.833,2.833 0.833,2.833 1.115,2.531 false 5.833,4.5 5.667,4.5 5.667,4.5 5.531,3.521 false 0.521,2.75 0.833,2.906 0.313,0.156 10 false *1 5.854,4.427 6.167,4.583 0.313,0.156 10 false *2
*1 WINDSHIELD HEADER PANEL SUB-ASSEMBLY *2 ROOF PANEL REINFORCEMENT SUB-ASSEMBLY REAR


K149148

K149144


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.



K149761N01
5.729,1.802 5.885,1.958 0.156,0.156 10 true A 1.021,1.719 1.177,1.875 0.156,0.156 10 true B 4.948,2.385 5.104,2.542 0.156,0.156 10 true C 4.365,2.448 4.521,2.604 0.156,0.156 10 true D 3.708,2.542 3.865,2.698 0.156,0.156 10 true E 3.125,1.948 3.281,2.104 0.156,0.156 10 true F 4.906,1.115 5.063,1.271 0.156,0.156 10 true G 4.25,1.135 4.406,1.292 0.156,0.156 10 true H 3.667,1.104 3.823,1.26 0.156,0.156 10 true I

Reference Value:
Area Measurement Area Measurement
A 726 mm (28.58 in.) B 721 mm (28.39 in.)
C 877 mm (34.53 in.) D 1047 mm (41.22 in.)
E 1251 mm (49.25 in.) F 2069 mm (81.46 in.)
G 1251 mm (49.25 in.) H 1032 mm (40.63 in.)
I 1264 mm (49.76 in.) - -