Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD › 2018.10–2020.01
BM3620E _01 Vehicle Exterior _077725 BODY PANEL _0383663 FIT STANDARD / ADJUSTMENT METHOD F

BODY PANEL  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to K are within the standard ranges.

B521967N01
1.75,0.208 1.906,0.406 0.156,0.198 10 false A 0.323,0.385 0.479,0.583 0.156,0.198 10 false B 1.729,2.677 1.885,2.875 0.156,0.198 10 false C 1.406,3.146 1.563,3.344 0.156,0.198 10 false D 4,0.875 4.156,1.073 0.156,0.198 10 false E 4.802,2.875 4.958,3.073 0.156,0.198 10 false F 4.667,3.25 4.823,3.448 0.156,0.198 10 false G 6.063,2.844 6.219,3.042 0.156,0.198 10 false H 5.917,3.25 6.073,3.448 0.156,0.198 10 false I 5.844,0.229 6,0.427 0.156,0.198 10 false J 5.406,0.427 5.563,0.625 0.156,0.198 10 false K

Standard Clearance:
Area Measurement Area Measurement
A 1.85 to 5.85 mm (0.0728 to 0.2303 in.) B
(Reference)
8.05 mm (0.317 in.)
C 1.85 to 5.85 mm (0.0728 to 0.2303 in.) D -1.85 to 2.15 mm (-0.0728 to 0.0846 in.)
E
(Reference)
7.95 mm (0.313 in.) F 3.5 to 6.5 mm (0.138 to 0.256 in.)
G 1.7 to 4.7 mm (0.0669 to 0.1850 in.) H 3.5 to 6.5 mm (0.138 to 0.256 in.)
I 0.4 to 3.4 mm (0.0157 to 0.1339 in.) J 2.8 to 5.8 mm (0.110 to 0.228 in.)
K -1.8 to 1.2 mm (-0.0709 to 0.0472 in.) - -


HINT:
·

Centering bolts are used to mount the hood hinge to the vehicle body and hood. The hood cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts (with washers) when making adjustments.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.





ADJUST HOOD SUB-ASSEMBLY


a.

Adjust the hood position.

i.
B521971

Loosen the 4 hinge bolts on the hood and adjust the hood position.


ii.

Move the hood and adjust the clearance between the hood and front fender.


iii.

Tighten the 4 hinge bolts on the hood after the adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.

Adjust the 2 cushion rubbers so that the hood and fender are aligned.

i.
B521972

HINT:

Raise or lower the front end of the hood by turning the cushion rubber.




c.
B521973N01
1.135,1.333 1.302,1.51 0.167,0.177 10 true 1 2.073,1.323 2.271,1.531 0.198,0.208 10 true 2 1.802,1.615 2,1.823 0.198,0.208 10 true 3

Adjust the hood lock.

i.

Loosen the 3 bolts.


ii.

Adjust the hood lock position so that the striker can enter it smoothly.


iii.

Tighten the 3 bolts after the adjustment in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to L are within the standard ranges.

B527077N01
0.885,4.208 1.115,4.458 0.229,0.25 10 false A 1.396,3.99 1.625,4.24 0.229,0.25 10 false B 1.448,1.49 1.677,1.74 0.229,0.25 10 false C 1.313,2.219 1.542,2.469 0.229,0.25 10 false D 2.969,0.385 3.198,0.635 0.229,0.25 10 false E 2.875,1.094 3.104,1.344 0.229,0.25 10 false F 5.125,0.448 5.344,0.667 0.219,0.219 10 true G 4.906,1.125 5.135,1.375 0.229,0.25 10 false H 6.156,2.573 6.385,2.823 0.229,0.25 10 false I 6.552,2.281 6.781,2.531 0.229,0.25 10 false J 6.031,4.219 6.26,4.469 0.229,0.25 10 false K 6.479,3.896 6.708,4.146 0.229,0.25 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 2.5 to 5.5 mm (0.0984 to 0.2165 in.) B -1.8 to 1.2 mm (-0.0709 to 0.0472 in.)
C 2.65 to 6.05 mm (0.104 to 0.238 in.) D 2.35 to 6.35 mm (0.0925 to 0.2500 in.)
E 2.65 to 6.05 mm (0.104 to 0.238 in.) F 1.65 to 6.15 mm (0.0650 to 0.2421 in.)
G 2.65 to 6.05 mm (0.104 to 0.238 in.) H 3.75 to 7.85 mm (0.148 to 0.309 in.)
I
(Reference)
5.1 mm (0.201 in.) J
(Reference)
0 mm (0 in.)
K 2.9 to 5.3 mm (0.114 to 0.209 in.) L -1.5 to 0.9 mm (-0.0591 to 0.0354 in.)


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.





ADJUST FRONT DOOR PANEL SUB-ASSEMBLY


a.
B527078

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B527079

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B527080

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and a hammer.


f.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to K are within the standard ranges.

B528015N01
1.688,0.708 1.844,0.906 0.156,0.198 10 false A 1.25,1.302 1.406,1.5 0.156,0.198 10 false B 0.854,1.896 1.01,2.094 0.156,0.198 10 false C 0.542,2.458 0.698,2.656 0.156,0.198 10 false D 1.021,3.5 1.177,3.698 0.156,0.198 10 false E 0.729,4.094 0.885,4.292 0.156,0.198 10 false F 4.104,0.333 4.26,0.531 0.156,0.198 10 false G 4.094,1 4.25,1.198 0.156,0.198 10 false H 5.688,1.01 5.844,1.208 0.156,0.198 10 false I 6.198,2.792 6.354,2.99 0.156,0.198 10 false J 6.594,3.354 6.75,3.552 0.156,0.198 10 false K

Standard Clearance:
Area Measurement Area Measurement
A
(Reference)
5.1 mm (0.201 in.) B
(Reference)
0 mm (0 in.)
C 2.9 to 5.3 mm (0.114 to 0.209 in.) D -1.5 to 0.9 mm (-0.0591 to 0.0354 in.)
E 2.9 to 5.3 mm (0.114 to 0.209 in.) F -1.5 to 0.9 mm (-0.0591 to 0.0354 in.)
G 2.65 to 6.05 mm (0.104 to 0.238 in.) H 3.15 to 7.15 mm (0.124 to 0.281 in.)
I 3.3 to 7.3 mm (0.130 to 0.287 in.) J 2.2 to 5.2 mm (0.0866 to 0.2047 in.)
K -1.8 to 1.2 mm (-0.0709 to 0.0472 in.) - -


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.





ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH


a.
B528016

Loosen the hinge bolts on the body and adjust the door position.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B528017

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B528018

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and a hammer.


f.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to H are within the standard ranges.

B528019N01
1.49,0.25 1.646,0.448 0.156,0.198 10 false A 1.063,0.854 1.219,1.052 0.156,0.198 10 false B 3.719,0.198 3.875,0.396 0.156,0.198 10 false C 3.292,0.76 3.448,0.958 0.156,0.198 10 false D 5.344,1.26 5.5,1.458 0.156,0.198 10 false E 5.896,2.458 6.052,2.656 0.156,0.198 10 false F 5.781,3.729 5.938,3.927 0.156,0.198 10 false G 4.896,4.281 5.052,4.479 0.156,0.198 10 false H

Standard Clearance:
Area Measurement Area Measurement
A 5.95 to 9.95 mm (0.234 to 0.392 in.) B -1.15 to 2.85 mm (-0.0453 to 0.1122 in.)
C 5.95 to 9.95 mm (0.234 to 0.392 in.) D -1.15 to 2.85 mm (-0.0453 to 0.1122 in.)
E 3.35 to 7.35 mm (0.132 to 0.290 in.) F 2.5 to 7.5 mm (0.0984 to 0.2953 in.)
G 3.35 to 7.35 mm (0.132 to 0.290 in.) H 4.55 to 9.55 mm (0.179 to 0.376 in.)


HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.




ADJUST BACK DOOR PANEL SUB-ASSEMBLY


a.
B528020

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


c.
B528021

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and a hammer.


d.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)