With the cowl top side upper panel assembly, center body pillar cut and join replacement sections and roof panel assembly removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)
Remove the A.
A is reused.
| *a | 260 mm (10.24 in.) | - | - |
Remove the front body pillar upper outer.
| *1 | FRONT BODY PILLAR UPPER OUTER | - | - |
Remove the roof side rail sub-assembly and front body pillar reinforce sub-assembly lower.
A indicates welds to remove for easier removal.
| *1 | ROOF SIDE RAIL SUB-ASSEMBLY | *2 | FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER |
When replace only the outer panel, please cut off a necessary range depending on a damage range.
Carefully cut the outer panel so not to damage the reinforcement.
Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Butt Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before temporarily installing the new parts, weld the roof side rail sub-assembly and front body pillar reinforce sub-assembly lower with the standard number of welding points.
| *1 | ROOF SIDE RAIL SUB-ASSEMBLY | *2 | FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Weld the roof side rail sub-assembly and front body pillar reinforce sub-assembly lower to the vehicle side.
| *1 | ROOF SIDE RAIL SUB-ASSEMBLY | *2 | FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER |
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 1500 MPa or 1180 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 980 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 1500 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 2 panels together including 1500 MPa or 1180 MPa ultra high strength steel.
| *a: Plug weld | Plug diameter | 10 mm (0.39 in.) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Weld the front body pillar upper outer to the vehicle side.
| *1 | FRONT BODY PILLAR UPPER OUTER | - | - |
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 3 panels or more together including 1500 MPa or 1180 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)
| *a: Plug weld | Plug diameter | Same as the standard method (See the introduction) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)
| *a: Plug weld | Plug diameter | Same as the standard method (See the introduction) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
| *a | Ultra High Strength Steel Welding Point | - | - |
When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)
| *a: Plug weld | Plug diameter | Same as the standard method (See the introduction) |
| Wire type | AWS A5.18 ER70S-3 | |
| Shield gas | Metal active gas |
Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.
Weld the A to the vehicle side.
After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)
After welding, apply body sealer to the corresponding parts. (See the painting/coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.