OUTLINE
A dual zone automatic air conditioning system (left and right independent control) or manual air conditioning system is available depending on the model.
An inside-and-outside dual air layer type air conditioning unit is used. The upper layer ensures anti fogging performance by introducing outside air, and the lower layer aims for ventilation loss reduction by circulating the inside air, achieving energy conservation.*1
S-FLOW control is used to concentrate the air outlets on the driver seat*2 or front seats when the temperature and moisture in the cabin are stable, aiming for a reduction in the burden on the air conditioning to achieve energy conservation.*3
*1: Models with inside-and-outside dual air layer type air conditioning unit
*2: Models with S-FLOW control and driver seat air outlet mode
*3: Models with automatic air conditioning system
SPECIFICATIONS
Air Conditioning System (HV Models)
| Component | Specifications | |
|---|---|---|
|
*1: Models with inside-and-outside dual air layer type air conditioning unit *2: Models without inside-and-outside dual air layer type air conditioning unit *3: Upper side *4: Lower side *5: Models using HFC-134a (R134a) refrigerant *6: Models using HFO-1234yf (R1234yf) refrigerant |
||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 263.9 mm x 120 mm x 27 mm
(10.4 in. x 4.72 in. x 1.06 in.) |
|
| Fin Pitch | 1.8 mm (0.0709 in.) | |
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite Brushless |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H)*1 | 122 mm x 55 mm (4.80 in. x 2.17 in.)*3
125 mm x 38 mm (4.92 in. x 1.50 in.)*4 |
|
| Fan Size (Dia. x H)*2 | 137 mm x 70 mm (5.39 in. x 2.76 in.) | |
| Cooler Condenser Assembly | Type | Multi-Flow IV (MF-IV) Sub-cool |
| Size (W x H x L) | 706 mm x 319 mm x 22 mm
(27.8 in. x 12.6 in. x 0.866 in.) |
|
| Fin Pitch | 2.7 mm (0.106 in.) | |
| Cooler Compressor Assembly | Type | ESB27C |
| Refrigerant | Type | HFC-134a (R-134a)*5
HFO-1234yf (R-1234yf)*6 |
| No. 1 Cooler Evaporator Sub-assembly | Type | Ejector Cycle System (ECS) |
| Size (W x H x L) | 279.7 mm x 231 mm x 38 mm
(11.0 in. x 9.09 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
Air Conditioning System (Gasoline Models)
| Component | Specifications | |
|---|---|---|
|
*1: Models with inside-and-outside dual air layer type air conditioning unit *2: Models without inside-and-outside dual air layer type air conditioning unit *3: Upper side *4: Lower side *5: Models using HFC-134a (R134a) refrigerant *6: Models using HFO-1234yf (R1234yf) refrigerant *7: Model with stop and start system *8: Model without stop and start system |
||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 263.9 mm x 120 mm x 27 mm
(10.4 in. x 4.72 in. x 1.06 in.) |
|
| Fin Pitch | 1.8 mm (0.0709 in.) | |
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite Brushless |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H)*1 | 122 mm x 55 mm (4.80 in. x 2.17 in.)*3
125 mm x 38 mm (4.92 in. x 1.50 in.)*4 |
|
| Fan Size (Dia. x H)*2 | 137 mm x 70 mm (5.39 in. x 2.76 in.) | |
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC) |
| Size (W x H x L) | 700 mm x 453 mm x 11.5 mm
(27.6 in. x 17.8 in. x 0.453 in.) |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
| Cooler Compressor Assembly | Type | 7SES17C |
| Refrigerant | Type | HFC-134a (R-134a)*5
HFO-1234yf (R-1234yf)*6 |
| No. 1 Cooler Evaporator Sub-assembly | Type | Cold Storage (CS)*7
Beneficial Refrigerant Stream (BRS)*8 |
| Size (W x H x L) | 279.7 mm x 231 mm x 38 mm
(11.0 in. x 9.09 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
MAIN FEATURES
The air conditioning system has the following features:
| Feature | Outline |
|---|---|
|
*1: Models with automatic air conditioning system *2: HV models *3: Gasoline models *4: Gasoline models with stop and start system *5: Gasoline models without stop and start system |
|
| High Performance | ·
Neural network control is used, so passengers can finely control the air conditioning for maximum comfort.*1 ·
The rear outlets are installed on the back of the center console and floor to ensure comfortable air conditioning performance for the rear passengers. ·
Pollen removal mode control is used to remove pollen in the area around the upper part of the bodies of the driver and front passenger. ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.*1 |
| Light Weight | ·
A bus connector with a built-in IC is used in a lightweight wire harness design to allow a reduced number of wires. ·
The use of this connector means that pulse pattern type servo motors can be used. |
| Compact | A blower motor with a built-in blower motor controller is used to achieve a compact construction for the front air conditioning system. |
| Others | The following parts are used to ensure high cooling performance while achieving a compact and lightweight construction:
·
Semi-center Location Air Conditioning Unit ·
ESB27C Type Compressor*2 ·
Ejector Cycle System (ECS) Evaporator*2 ·
7SES17C Type Compressor*3 ·
Cold Storage (CS) Evaporator*4 ·
Beneficial Refrigerant Stream (BRS) Evaporator*5 ·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly ·
Multi-Flow IV (MF-IV) Sub-cool Condenser |
PRECAUTION
Precaution for Refrigerant HFO-1234yf (R1234yf)
Compatibility
The parts used in the refrigerant cycle, the compressor oil, etc. of the HFO-1234yf (R1234yf) system are not compatible with the conventional HFC-134a (R134a) system.
Always use HFO-1234yf (R1234yf) as the refrigerant.
Do not charge the system with refrigerant near open flames, as HFO-1234yf (R1234yf) is combustible.
When charging the system with refrigerant, make sure the area is well ventilated (especially be careful in areas where the gas can easily accumulate such as under lifts and in garage pits, as the gas is heavier than air).
Follow any local regulations regarding combustible gases.
Be sure to use a refrigerant recovery unit that is compatible with HFO-1234yf (R1234yf) systems.
The shape of the service port for refrigerant charging has an exclusive design conforming to international standards for HFO-1234yf (R1234yf) to prevent improper refrigerant charging.
Compressor Oil (HV Models)
Always use ND-OIL 11 as the compressor oil.
When parts of the air conditioning system are removed, quickly block off any areas that are exposed to the outside air with plugs, vinyl tape, etc., as the oil used for HFO-1234yf (R1234yf) systems absorbs moisture easily.
Do not allow the compressor oil to spray, as the oil used for HFO-1234yf (R1234yf) systems has harmful effects on acrylic resins.
Compressor Oil (Gasoline Models)
Always use ND-OIL 12 as the compressor oil.
When parts of the air conditioning system are removed, quickly block off any areas that are exposed to the outside air with plugs, vinyl tape, etc., as the oil used for HFO-1234yf (R1234yf) systems absorbs moisture easily.
Do not allow the compressor oil to spray, as the oil used for HFO-1234yf (R1234yf) systems has harmful effects on acrylic resins.
Ignition Switch Expressions (Gasoline Models)
The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.
| Expression | Ignition Switch
(Position) |
Engine Switch
(Condition) |
|---|---|---|
| Ignition Switch off | LOCK | Off (Lock) |
| Ignition Switch ACC | ACC | On (ACC) |
| Ignition Switch ON | ON | On (IG) |
| Engine Start | START | On (Start) |