FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*: Wiper operating, blower motor operating, or taillight switch on, etc. |
||
| ECM | ·
Detects the electrical load condition*. ·
Determines the state of the battery based on the input/output current, voltage, temperature, SOC (State of Charge), SOH (State of Health) and self-diagnosis results determined by the battery state sensor assembly. ·
Calculates the request voltage based on the electrical load*, state of the battery and various sensors, and sends the request voltage signal to the IC regulator. ·
Controls the voltage generated by the generator assembly. |
|
| Generator Assembly | IC Regulator | Receives request voltage command signals from the ECM and charges the battery. |
| Battery State Sensor Assembly | Outputs the state of the battery based on the input/output current, voltage, temperature, SOC (State of Charge), SOH (State of Health), SOF (State of Function) and self-diagnosis results to the ECM via LIN communication. | |
| Battery | Supplies power to the electrical components such as the blower motor, wiper, lights and each ECU. | |
SYSTEM CONTROL
The ECM and generator assembly sends and receives signals via LIN communication (bidirectional multiplex communication) to accurately adjust the voltage generated by the generator assembly.
The battery state sensor assembly detects the battery temperature and outputs the value to the ECM, and the ECM judges whether to enter the generator operates in constant voltage generation mode based on the value.
Charging control selects an optimal control mode according to the battery status and vehicle conditions. The provided control modes are basic control mode, supplementary charging mode and refresh charging mode.
Basic Control Mode
The ECM decreases the generated voltage during acceleration and increases it during deceleration in order to reduce the amount of engine load caused by the generator assembly, improving fuel efficiency.
During idling and when driving at a constant speed, the ECM adjusts the generated voltage to bring the current integrated value* closer to the target value.
*: Integrated value of the battery input/output current as detected by the battery state sensor assembly.
Supplementary Charging Mode
This mode charges the battery using constant voltage control if the battery capacity is low.
Basic control mode is used when the battery capacity is a specified amount or more.
Refresh Charging Mode
This mode suppresses decreases in the battery lifespan by regularly* performing constant voltage control to charge the battery. Also, the operation time of constant voltage control is longer in this mode compared to supplementary charging mode.
*: When a total of approximately 30 hours has elapsed with the engine switch turned on (IG).
Constant voltage control is also performed for a long time when the battery capacity is low after the battery is replaced or the vehicle is left for a long period of time.
FAIL-SAFE
Due to fail-safe operation, when a sensor malfunctions, basic control is stopped and the system enters constant voltage generation mode. Also, even outside of auxiliary charging mode, due to operating circumstances such as battery condition and electrical load, basic control may be stopped and the system may enter constant voltage generation mode.
| Judgment Condition | Reasoning | Vehicle Behavior |
|---|---|---|
| Low Battery Capacity | If the battery state is bad, the basic control discontinues, and helping prevent a decrease in battery capacity. | "Basic Control Stops" to "Constant Voltage Generation Mode" |
| Low or High Battery Temperature | If the battery temperature is too low or high, it may cause the battery capacity or lifetime to decrease. | |
| Wiper Operating, Blower Motor Operating (Over High Load), or Taillight Switch On*1 | The generated voltage changes due to charging control. As this can impact the operation of electrical devices, the system temporarily stops basic control to help to prevent any perceived abnormality in the operation of these devices. | |
| Each Sensor Malfunction | In case of sensor malfunction, basic control discontinues, to help to prevent battery capacity decrease. | "Basic Control Stops" to "Constant Voltage Generation Mode (Autonomous Generation Mode*2)" |
| Generator Assembly Malfunction | In case of generator assembly malfunction, basic control discontinues, to help to prevent battery capacity decrease and to protect the battery. | |
| Communication Failure (LIN Communication between the Generator Assembly, ECM and the Battery State Sensor Assembly) | In case of LIN communication failure between ECM to generator assembly or to battery state sensor assembly, basic control discontinues, to help to prevent battery capacity decrease and to protect the battery. |
*1: Except models for Korea
*2: In this mode, voltage is generated at a constant level using the IC regulator function built into the generator assembly.