OUTLINE
The M20A-FKS engine is an in-line 4-cylinder, 2.0 liter, 16 valve DOHC engine.
The engine adopts the Dual Variable Valve Timing-intelligent (Dual VVT-i) system which achieves optimal valve timing by using electric motors to actuate the intake camshaft actuators and engine oil pressure to actuate the exhaust camshaft actuators. In addition, this engine uses a high-expansion ratio Atkinson cycle, Direct injection 4-stroke gasoline engine Superior version (D-4S) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. As a result, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.
SPECIFICATION
| Item | Specification | ||
|---|---|---|---|
|
*1: Models with Gasoline Particulate Filter (GPF) system *2: Models without Gasoline Particulate Filter (GPF) system *3: The figure shown is the weight of the part without coolant and oil. |
|||
| Engine Type | M20A-FKS | ||
| No. of Cyls. & Arrangement | 4-cylinder, In-line | ||
| Valve Mechanism | 16-valve DOHC, Chain Drive
(With VVT-iE and VVT-i) |
||
| Combustion Chamber | Pentroof Type | ||
| Flow of Intake and Exhaust Gasses | Cross-flow | ||
| Fuel System | Sequential Multiport Fuel Injection (SFI) D-4S | ||
| Ignition System | Direct Ignition System (DIS) | ||
| Displacement | cm3 (cu. in.) | 1987 (121.3) | |
| Bore x Stroke | mm (in.) | 80.5 x 97.6 (3.17 x 3.84) | |
| Compression Ratio | 13.0 : 1 | ||
| Max. Output (EEC) | kW@rpm | 129@6600*1 | |
| 127@6600*2 | |||
| Max. Torque (EEC) | N*m@rpm | 208@4300 to 5200*1 | |
| 203@4400 to 4900*2 | |||
| Valve Timing | Intake | Open | -30° to 40° BTDC |
| Closed | 110° to 40° ABDC | ||
| Exhaust | Open | 3° to 44° BBDC | |
| Closed | 41° to 0° ATDC | ||
| Spark Plug | Type | DENSO Made | FC20HR-Q8 |
| Plug Gap | mm (in.) | 0.7 to 0.8 (0.0276 to 0.0315) | |
| Firing Order | 1 - 3 - 4 - 2 | ||
| Research Octane Number | 95 or higher*1 | ||
| 91 or higher*2 | |||
| Octane Rating | 87 or higher*2 | ||
| Emission Regulation | EURO 6d*1 | ||
| EURO 6 and earlier*2 | |||
| Engine Service Mass*3 (Reference) | kg (lb.) | 104 (230.2) | |
MAIN FEATURES
The M20A-FKS engine has achieved the following through the use of the items listed in the table below.
High performance and reliability
Low noise and vibration
Lightweight and compact design
Good serviceability
Clean emissions and improved fuel economy
| Item | i | ii | iii | iv | v | |
|---|---|---|---|---|---|---|
|
○: Applicable -: Not applicable |
||||||
| The high-expansion ratio Atkinson cycle is adopted. | ○ | - | - | - | ○ | |
| Engine Proper | An aluminum cylinder block sub-assembly is used. | - | - | ○ | - | - |
| Spiny-type liners are used in the cylinder bores. | ○ | - | - | - | - | |
| A cylinder block water jacket spacer is used. | ○ | - | - | - | ○ | |
| The piston skirt is coated with resin. | ○ | ○ | - | - | ○ | |
| An offset crankshaft is used. | ○ | ○ | - | - | ○ | |
| Laser cladded valve seats are used for the intake side. | ○ | - | - | - | ○ | |
| A chain cover that consists of the timing chain cover assembly and No. 2 timing chain cover assembly is used. | ○ | - | - | - | - | |
| Bolts with smaller heads than standard bolts of the same thread diameter are used. | ○ | - | ○ | - | - | |
| Valve Mechanism | The Variable Valve Timing-intelligent by Electric motor (VVT-iE) system is used for the intake camshaft sub-assembly. | ○ | - | - | - | ○ |
| The Variable Valve Timing-intelligent (VVT-i) system is used for the exhaust camshaft sub-assembly. | ○ | - | - | - | ○ | |
| A chain sub-assembly and No. 1 chain tensioner assembly are used. | - | ○ | - | ○ | - | |
| Valve lash adjuster assemblies are used. | ○ | ○ | - | ○ | - | |
| No. 1 valve rocker arm sub-assemblies are used. | ○ | - | - | - | ○ | |
| Lubrication System | A cartridge type oil filter sub-assembly is used. | - | - | - | ○ | - |
| An electronically controlled variable displacement oil pump is used. | ○ | - | - | - | ○ | |
| An engine oil level sensor is used. | - | - | - | - | ○ | |
| An engine oil cooler (oil cooler assembly) is used. | ○ | - | - | - | - | |
| Cooling System | TOYOTA Genuine Super Long Life Coolant (SLLC) is used. | - | - | - | ○ | - |
| A variable cooling control system is used. | ○ | - | - | - | ○ | |
| An electric engine water pump is used. | - | - | - | - | ○ | |
| Intake and Exhaust System | An intake manifold made of plastic is used. | - | ○ | ○ | - | - |
| A linkless type throttle body with motor assembly is used. | - | - | ○ | ○ | - | |
| A stainless steel exhaust manifold is used. | - | - | ○ | - | - | |
| Emission Control System | A step motor type Exhaust Gas Recirculation (EGR) valve is used. | ○ | - | - | - | ○ |
| A water-cooled type Exhaust Gas Recirculation (EGR) cooler is used. | ○ | - | - | - | ○ | |
| An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. | - | - | - | - | ○ | |
| Fuel System | A Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. | ○ | - | - | - | ○ |
| A fuel returnless system is used. | - | - | ○ | ○ | ○ | |
| Quick connectors are used to connect the fuel hoses with the fuel pipes. | - | - | - | ○ | - | |
| 10-hole type low pressure port fuel injector assemblies are used. | ○ | - | - | - | ○ | |
| 6-hole type high pressure direct fuel injector assemblies are used. | ○ | ○ | - | - | ○ | |
| Ignition System | The Direct Ignition System (DIS) is used. | ○ | - | - | ○ | ○ |
| Long-reach type iridium-tipped spark plugs are used. | ○ | - | - | ○ | ○ | |
| Serpentine Belt Drive System | A serpentine belt drive system is used. | - | - | ○ | ○ | - |
| Engine Control System | Magnetic Resistance Element (MRE) type camshaft position sensors and crank position sensor are used. | ○ | - | - | - | ○ |
| The Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ | |
| An evaporative emission control system is used. | - | - | - | - | ○ | |
Location of small-head bolts