Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM
NM3620E _59 Vehicle Exterior _076669 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0373195 VEHICLE PROXIMITY NOTIFICATION SYSTEM CO CONTROL F

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  CONTROL  VEHICLE PROXIMITY NOTIFICATION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Vehicle Approaching Speaker Controller Starts, stops and controls the output sound according to input signals from various ECUs.
Vehicle Approaching Speaker Assembly Emits warning sounds based on the operation signal received from the vehicle approaching speaker controller.
Combination Meter Assembly
·

Multi-information Display


Displays a warning message when there is a malfunction in the vehicle proximity notification system.
Stop Light Switch Assembly Outputs the operation condition of the brake pedal.
Hybrid Vehicle Control ECU Sends the shift position signal, stop light switch signal, front motor speed signal and engine start/stop signal to the vehicle approaching speaker controller.
Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


Outputs a vehicle speed signal to the vehicle approaching speaker controller.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.


OPERATING CONDITION


Condition Outline
System Active The vehicle proximity notification system operates (emits a warning sound) when all of the following conditions are met:
·

Engine is stopped.

·

Vehicle speed is 25 km/h (16 mph) or less.

·

Shift position is any position other than P.

·

Vehicle speed exceeds 0 km/h (0 mph), front motor speed exceeds 32 rpm, or stop light switch is turned from on to off.


System Stop The vehicle proximity notification system stops operating when any of the following conditions is met:
·

The engine starts.

·

The vehicle speed is more than 25 km/h (16 mph).

·

Shift position is P.

·

With a vehicle speed of 0 km/h (0 mph) and a front motor speed of 32 rpm or less, the stop light switch is continuously on for approximately 0.24 seconds or more.

·

With a vehicle speed of 0 km/h (0 mph) and a front motor speed of 32 rpm or less, the stop light switch is continuously off for approximately 3 seconds or more.*



HINT:

*: When the system is stopped due to a vehicle speed of 0 km/h (0mph), a front motor speed of 32 rpm or less and the stop lights being off for approximately 3 seconds or more, the system operates again when the vehicle speed is 1 km/h (1mph) or more, the front motor speed is 33 rpm or more or the brake pedal is operated.



SYSTEM CONTROL


Control Outline
Vehicle Speed Linked Control
·

Controls the volume and pitch of the output sound according to the received vehicle speed.

·

The sound output when the vehicle speed is 0 km/h (0mph) is considered the original sound. During acceleration, the volume and pitch of the sound are increased, and during deceleration, the volume and pitch are decreased, outputting a sound that artificially reflects vehicle acceleration and deceleration.


Fade-in/Fade Out Control When the system starts operating, the warning sound volume gradually increases, and when system operation is stopped, the sound volume gradually decreases.
Control during Reverse Operation When the vehicle is being driven in reverse, the warning sound volume becomes higher than it is when driving forward so that the sound is easy to hear even while reversing.


FUNCTION


a.

Warning Indication

i.

The combination meter assembly uses the multi-information display to notify the driver of vehicle proximity notification system malfunctions.


ii.

When the system is not available, the following warning occurs to warn the driver.

When a System Malfunction is Detected
Multi-information Display Detail Buzzer DTC
Proximity Notification System Malfunction Visit Your Dealer This message appears when the vehicle approaching speaker controller detects a system malfunction Sounds Repair is required DTCs are stored




DIAGNOSIS


a.

The vehicle approaching speaker controller will also store DTCs. The DTCs can be read by using the GTS. For details, refer to the Repair Manual.