FUNCTION OF MAIN COMPONENTS
The main components in the driver seat control system (with memory seat function) have the following functions:
| Component | Outline |
|---|---|
|
*1: HV models *2: Gasoline models |
|
| Position Control ECU Assembly | ·
Operates the front power seat. ·
Operates the motors in accordance with the signals from the front power seat switch. ·
Registers and recalls seat positions in accordance with the operation of the seat memory switch. |
| Front Power Seat Switch | Operates the motors in accordance with the signals from the front power seat switch. |
| Seat Memory Switch | Operates the memory seat function. |
| Main Body ECU (Multiplex Network Body ECU) | Various signals are transmitted and received via the CAN communication. |
| Front Door Courtesy Light Switch Assembly (for Driver Door) | Detects whether the driver door is open or closed and outputs the result to the main body ECU. |
| Certification ECU (Smart Key ECU Assembly) | Sends memory call recall command signals to the main body ECU via CAN communication. |
| Hybrid Vehicle Control ECU*1 | Sends shift position signals to the main body ECU. |
| ECM*2 | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
OPERATING CONDITION
Memory Seat Function (Models with Memory Seat Function)
The memory seat function operating conditions are as follows:
| Function | Condition | Operation |
|---|---|---|
|
*1: HV models *2: Gasoline models |
||
| Memory | Either of the following conditions is met while the power switch is on (IG)*1 or engine switch is on (IG)*2:
·
Button 1 or 2 (seat memory switch) is pushed within 3 seconds after the "SET" button is pushed. |
·
Stores the seat position. ·
When the memory setting is completed, the buzzer sounds for 0.5 seconds. |
| Recall | ·
Button 1 or 2 (seat memory switch) is pushed within 180 seconds after the driver door has been opened while the power switch is off*1 or engine switch is off*2. ·
Button 1 or 2 (seat memory switch) is pushed. |
·
The seat position that was memorized in the position control ECU assembly is recalled. ·
The buzzer sounds for 0.1 seconds once the stored seat position is reproduced. |
·
Power switch is on (IG)*1 or engine switch is on (IG)*2. ·
Shift position is in P. ·
Button 1 or 2 (seat memory switch) is pushed. |
||
| Button 1 or 2 (seat memory switch) is pushed within 60 seconds after the power switch*1 or engine switch*2 has been turned off and the driver door has been closed. | ||
| Memory Call | ·
A key ID is registered to button 1 or 2 (seat memory switch). ·
Power switch*1 or engine switch*2 is off. ·
The inside of the outside door handle is touched or the electrical key transmitter sub-assembly unlock button is pushed to unlock, and then the driver door is opened. |
·
The seat position that was memorized in the position control ECU assembly is recalled. ·
The buzzer sounds for 0.1 seconds once the stored seat position is reproduced. |
FUNCTION
Front Power Seat Control System
The power seat control system has the following functions:
| Function | Outline | |
|---|---|---|
|
*: Models with memory seat function |
||
| Manual Control | The user can perform seat slide, seat reclining, front vertical, seat lifter and lumbar support adjustments by operating the front power seat switch. | |
| Memory* | Memory | The memory seat function can memorize 2 different seat positions. |
| Recall | The recall function can recall 2 different memorized seat positions. | |
| Memory Call | The memory call function, which utilizes the key IDs, is used to memorize and recall the optimal driving position for a person possessing the electrical key transmitter sub-assembly. | |
OPERATION
Seat Position Detection Method (Models with Memory Seat Function)
The Hall IC installed on the power seat motor generates pulses corresponding to the speed of the motor. These pulses are then picked up by the position control ECU assembly in order to detect the seat position.
| *1 | Power Seat Motor | *2 | Position Control ECU Assembly |
| *3 | Hall IC | - | - |
| *a | Current Pulsation Generated by Motor | - | - |
DIAGNOSIS (Models with Memory Seat Function)
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The Diagnostic Trouble Codes (DTCs) of malfunctions can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.