Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CVT SYSTEM
NM3620E _52 Drivetrain _076476 K120 MULTIDRIVE / CVT _0375429 CVT SYSTEM GE GENERAL F

K120 MULTIDRIVE / CVT  CVT SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

A K120 Continuously Variable Transaxle (CVT) is used.


b.

A 10-speed sport sequential shiftmatic system is used.


c.

A straight type shift lever is used.


d.

A CVT fluid warmer is used in the CVT fluid cooling system.


e.

A 2 discharge port oil pump system is used.


f.

In order to ensure CVT fluid pressure when the Stop & Start System is operating, a CVT electric oil pump is provided. For details, see the Stop & Start System section.*

*: Models with stop and start system.


g.

In addition to the conventional metal belt between pulleys that transmits motive force, a gear transmission mechanism similar to an MT that is used when starting off and driving at low speeds has been added.



SPECIFICATION


Continuously Variable Transaxle

*1: Differential included.

*2: The weight shown is when the transaxle is filled with fluid.

Shift Mechanism Type Pulley and Steel Belt
Forward/Reverse Switching Mechanism Single Pinion Type Planetary Gear
Gear Ratio Forward 3.377
Reverse 3.136
Pulley Ratio Forward 2.236 to 0.447
Reverse -
Final Gear Ratio 4.262
Shift Pattern P - R - N - D - M
Fluid Capacity*1 Models with Stop & Start System 8.3 Liters (9.0 US qts, 7.5 Imp.qts)
Models without Stop & Start System 8.6 Liters (9.1 US qts, 7.6 Imp.qts)
Fluid Type Toyota Genuine CVT Fluid FE
Weight (Reference)*2 Models with Stop & Start System 90 kg (198.4 lb)
Models without Stop & Start System 89 kg (196.2 lb)

Gears (No. of Gear Teeth)
Gear Transmission Mechanism No. 1 Drive Gear 27
No. 1 Driven Gear 40
No. 2 Drive Gear 25
No. 2 Driven Gear 57
Planetary Gear Sun Gear 39
No. 1 Pinion 18
No. 2 Pinion 17
Ring Gear 81
Reduction Gear Drive Gear 31
Driven Gear 37
Final Gear Drive Gear Teeth 23
Driven Gear Teeth 73

Friction Engagement Components (No. of Discs)
No. 1 Clutch 3
No. 2 Clutch 4
No. 1 Brake 3

Torque Converter Assembly
Torque Converter Assembly Type 3-element, 1-step, 2-phase
Stall Torque Ratio 1.8


MAIN FEATURES


a.

The K120 CVT has achieved the following characteristics through the use of the items listed below.

○: Applicable

-: Not applicable

Item Fuel Economy Power Efficiency Driveability Quietness Compact and Lightweight
Flat Torus Torque Converter ○ ○ ○
Synchro Engagement Gear Transmission Mechanism ○ ○ ○ ○
Compact Continuously Variable Transmission Mechanism ○ ○ ○
Narrow Angle Belt ○ ○
Belt/Gear Transmission Switching Mechanism ○ ○ ○ ○
Vane Type Oil Pump ○ ○
2 Discharge Port Oil Pump ○
Low Viscosity CVT Fluid FE ○
Gear Ratio Pressure Control ○ ○
Oil Pressure Controller Front Arrangement ○ ○
Valve Body Artificial Aging Treatment Added ○
Electronic Control System Automatic Shift Control ○ ○ ○
Acceleration Improvement Control ○ ○
Deceleration Improvement Control ○
10-speed Sport Sequential Shiftmatic ○
Uphill/Downhill Shift Control ○
Engine-CVT Integrated Control ○ ○ ○
Flex Lock-up Control ○ ○ ○
Clutch Capacity Control ○ ○



PRECAUTION


a.

Ignition Switch Expressions

i.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)