Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for HV Model)
NM3620E _58 Vehicle Interior _077397 THEFT DETERRENT / KEYLESS ENTRY _0376109 ENTRY AND START SYSTEM(for HV Model) CO CONTROL F

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for HV Model)  CONTROL  ENTRY AND START CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components for the entry function have the following functions:*

*: Models with entry function


Component Function

*1: Models with power back door system

*2: Destination package for Korea

*3: Models with hands free power back door

*4: Models without power back door system

*5: Models with answer back buzzer function

*6: Models with multimedia system or navigation system

Electrical Key (Electrical Key Transmitter Sub-assembly)
·

Receives the signals from the antennas and returns the ID code to the door control receiver.

·

Outputs information such as the key ID and vehicle ID when request signals that are output by the indoor electrical key antennas, door electrical key antennas and outside electrical key antenna are received.

·

Outputs a request signal when the lock button, unlock button, power back door button*1 or panic button*2 on the electrical key is pushed.

·

Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.


Door Control Receiver Receives the ID code from the electrical key in the actuation area and transmits it to the certification ECU.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) Receives a request signal from the certification ECU and forms an actuation area in the vehicle.
No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor)
No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)
Electrical Key Antenna (Outside Back Door) Receives a request signal from the certification ECU and forms an actuation area around the back door.
Front Door Outside Handle Assembly LH Unlock Sensor Detects user entry unlock operations and transmits the door unlock request signal to the certification ECU.
Lock Sensor Detects user entry lock operations and transmits the door lock request signal to the certification ECU.
Door Electrical Key Antenna Receives the request signal from the certification ECU and forms an actuation area around the front door LH.
Front Door Outside Handle Assembly RH Unlock Sensor Detects user entry unlock operations and transmits the door unlock request signal to the certification ECU.
Lock Sensor Detects user entry lock operations and transmits the door lock request signal to the certification ECU.
Door Electrical Key Antenna Receives the request signal from the certification ECU and forms an actuation area around the front door RH.
Back Door Opener Switch Assembly Back Door Opener Switch Transmits a back door open request signal to the certification ECU.
Back Door Lock Switch Transmits a door lock request signal to the certification ECU.
Kick Door Control Sensor*3 Detects touchless kick actuation operations and outputs signals to the power back door ECU.
Instrument Panel Junction Block Assembly D DR UNLOCK Relay Inputs driver door unlock request signals from the main body ECU and operates the driver door lock motor.
L/D DR UNLOCK Relay Inputs passenger door unlock request signals from the main body ECU and operates the door lock motors at the front passenger seat and rear seats.
ALL DR LOCK Relay Inputs door lock request signals from the main body ECU and operates the door lock motor of all doors.
BDL Relay*4 Inputs back door open request signals from the main body ECU and operates the back door lock motor.
Front Door Lock with Motor Assembly (for Driver Door)
·

Door Lock Motor

·

Door Lock Position Switch

·

Door Lock Control Switch


·

Rotates the built-in door lock motor to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.

·

Detects the condition of the built-in door lock control switch and outputs mechanical key lock/unlock request signals to the main body ECU.


Front Door Lock with Motor Assembly (for Front Passenger Door)
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Rear Door Lock with Motor Assembly LH
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Rear Door Lock with Motor Assembly RH
·

Door Lock Motor

·

Door Lock Position Switch


·

Rotates the built-in door lock motor to lock and unlock the doors.

·

Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU.


Back Door Lock with Courtesy Light Switch Assembly*4
·

Back Door Lock Motor

·

Courtesy Switch


·

Drives the motor in response to signals from the main body ECU and releases the back door latch.

·

Detects whether the back door is open or closed and sends this information to the main body ECU.


Back Door Lock with Courtesy Light Switch Assembly*1
·

Back Door Lock Motor

·

Sector Switch

·

Pawl Switch

·

Latch Switch

·

Courtesy Switch


·

Drives the motor in response to signals from the power back door ECU and releases the back door latch.

·

Detects whether the back door is open or closed and sends this information to the main body ECU and power back door ECU.


Front Door Courtesy Light Switch Assembly (LH) Outputs open/close signals for the front door LH to the main body ECU.
Front Door Courtesy Light Switch Assembly (RH) Outputs open/close signals for the front door RH to the main body ECU.
Rear Door Courtesy Light Switch Assembly (LH) Outputs open/close signals for the rear door LH to the main body ECU.
Rear Door Courtesy Light Switch Assembly (RH) Outputs open/close signals for the rear door RH to the main body ECU.
Wireless Door Lock Buzzer
·

Sounds as an answer back for entry lock/unlock and wireless lock/unlock to inform the driver.*5

·

Sounds to inform the driver of malfunctions in the entry and start system.


Certification ECU (Smart Key ECU Assembly)
·

Controls the entry and start system in accordance with the signals received from the switches and each ECU.

·

Judges and certifies the electrical key.

·

Controls the antennas and forms detection areas.

·

Transmits the door lock/unlock request signals during the entry function.

·

Sends wireless door lock control signals that are input from the door control receiver to the main body ECU.

·

Sends warning request signals to the main body ECU or combination meter assembly when warning conditions are met.


Main Body ECU (Multiplex Network Body ECU)
·

Receives the request signal from the certification ECU and actuates the door lock motors to unlock or lock all the doors.

·

Transmits the condition of each door to the certification ECU.

·

Checks whether all door lock/unlock operations are complete, sends hazard warning light operation signals to the combination meter assembly, outputs sounding request signals to the wireless door lock buzzer*5 and performs answer back operations.

·

Receives warning request signals from the certification ECU and outputs sounding request signals to the wireless door lock buzzer when warning conditions are met.

·

Sends power back door open signals to the power back door ECU.*1

·

Receives back door open signals from ECUs and switches, outputs unlock signals to the back door lock motor.*4


Power Back Door ECU (Multiplex Network Door ECU)*1 Controls the power back door system in accordance with signals received from the switches, sensors and ECUs.
Hybrid Vehicle Control ECU Sends shift position signals and brake pedal operation signals to the main body ECU.
Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


Sends vehicle speed signals to the main body ECU.
Radio and Display Receiver Assembly*6
·

Displays the settings screen.

·

Sends customization information to the main body ECU.


Combination Meter Assembly
·

Displays a message on the multi-information display when an entry unlock mode condition or system malfunction occurs.

·

Sounds the buzzer to inform the driver of malfunctions in the entry and start system.

·

Flashes the hazard warning lights when an answer back operation is performed.

·

Sends vehicle speed signals to the certification ECU.


Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3
·

The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.

·

The Global TechStream (GTS) can be connected to change settings as desired by the user.




b.

The main components for the start function have the following functions:

Component Function
Electrical Key (Electrical Key Transmitter Sub-assembly)
·

Receives the signals from the antennas and returns the ID code to the door control receiver.

·

Outputs information such as the key ID and vehicle ID when request signals that are output by the indoor electrical key antennas, door electrical key antennas and outside electrical key antenna are received.

·

Outputs information such as the key ID and vehicle ID when the radio wave signal that is output by the transponder key amplifier in the power switch is received.


Door Control Receiver Receives the ID code from the electrical key in the actuation area and transmits it to the certification ECU.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) Receives a request signal from the certification ECU and forms the actuation area in the vehicle.
No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor)
No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)
Power Switch (Push Start Switch)
·

Transponder Key Amplifier


·

Transmits the power switch signal to the certification ECU.

·

Receives the ID code and transmits it to the certification ECU when the key battery is too weak to respond to the tuner based on the signals from the indoor electrical key antennas.


Stop Light Switch Assembly Outputs the state of the brake pedal to the certification ECU.
Certification ECU (Smart Key ECU Assembly)
·

Controls the entry and start system in accordance with the signals received from the switches and each ECU.

·

Controls the start function in accordance with the signals received from the switches and each ECU.

·

Switches the power source ("power switch") among 4 modes (off, on (ACC), on (IG), start) in accordance with the shift position and the brake pedal signal.

·

Certifies the ID code received from the door control receiver and transmits the certification results to the ID code box and steering lock ECU.

·

Judges and certifies the electrical key.

·

Controls the antennas and forms detection areas.

·

Transmits the steering wheel lock/unlock signals.

·

Transmits the immobiliser set/unset request signals.

·

Records the ID codes between the certification ECU, ID code box and steering lock ECU.

·

Controls the security indicator light operation, power source state display (ACCESSORY and IGNITION ON) and key certification indicator display.

·

Sends warning request signals to the main body ECU or combination meter assembly when warning conditions are met.


Hybrid Vehicle Control ECU
·

Receives hybrid system start permission signals from the certification ECU and starts the hybrid system.

·

Sends shift position signals and brake pedal operation signals to the main body ECU.


ECM Sends the engine speed signal to the certification ECU.
Steering Lock Actuator or Upper Bracket Assembly
·

Steering Lock ECU


Receives steering wheel unlock/lock request signals from the certification ECU, and activates the steering lock motor.
Shift Lock Control Unit Assembly
·

Shift Control ECU


Sends shift position P signals to the certification ECU.
ID Code Box (Immobiliser Code ECU) Receives the steering unlock or immobiliser unset request signals from the certification ECU, certifies them and transmits each unset signal to the steering lock ECU or hybrid vehicle control ECU.
Combination Meter Assembly
·

Displays a message on the multi-information display when a power source state or system malfunction occurs.

·

Sounds the buzzer to inform the driver of malfunctions in the entry and start system.

·

Blinks the security indicator light to inform the user that the immobiliser system is set.

·

Sends vehicle speed signals to the certification ECU.


Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.



OPERATION


a.

The special functions of the entry and start system only work when the electrical key is in the actuation area formed by the antennas.


b.

The indoor electrical key antennas form the actuation area of the start function.


c.

The door electrical key antennas and the electrical key antenna form the actuation area of the entry function.

Y226811C02
2.76,2.854 1.469,1.698 true 3.135,3.802 2.5,4.927 true 3.698,2.906 3.531,4.948 true 5.417,2.896 6.365,2.25 true 3.125,1.969 2.396,0.979 true 4.406,2.917 5.396,4.333 true 1.26,1.552 1.573,1.708 0.313,0.156 10 false *1 2.354,4.958 2.792,5.115 0.438,0.156 10 false *2 (*A) 3.438,5.01 3.75,5.167 0.313,0.156 10 false *3 5.406,4.375 5.865,4.594 0.458,0.219 10 false *4 6.396,2.115 6.833,2.313 0.438,0.198 10 false *5 (*A) 2.26,0.792 2.698,0.969 0.438,0.177 10 false *6 (*A)
*A Models with Entry Function - -
*1 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) *2 Front Door Outside Handle Assembly LH
·

Door Electrical Key Antenna


*3 No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor) *4 No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)
*5 Electrical Key Antenna (Outside Back Door) *6 Front Door Outside Handle Assembly RH
·

Door Electrical Key Antenna


V100144

Exterior Actuation Area
V100145

Interior Actuation Area
V100155

Outside Back Door Actuation Area - -


Actuation Area Details

*1: Models with entry function

*2: Models with hands free power back door

Interior The interior actuation area of the indoor electrical key antennas (front, rear, inside luggage compartment) is formed when the driver door is opened or closed, while the brake pedal is depressed, when the power switch is pushed, when a warning is activated, or when the lock sensor or lock switch is on*1.
Exterior*1 The exterior actuation area formed by the front door electrical key antennas and the outside electrical key antenna is approximately 0.7 m to 1.0 m (2.3 ft. to 3.3 ft.) from the door outside handle or the center of the rear bumper.
Around Front Doors*1 The exterior actuation area of the door electrical key antennas is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way, the presence of an electrical key is detected. When locking the door using the lock sensor on the door outside handle, the actuation area is formed when the lock sensor is touched.
Around Back Door*1 The exterior actuation area of the outside electrical key antenna is formed when the lock switch or back door opener switch is on or performing the touchless kick actuation operation*2.



FUNCTION


a.

The entry and start system consists of the following functions:

Function Outline

*1: Models with entry function

*2: Models with power back door system

*3: Models with hands free power back door

*4: Models with answer back buzzer function

*5: Except destination package for Korea

*6: Destination package for Korea

Wireless Door Lock Control This function is a convenient system for locking and unlocking all the doors at a distance. The operation of this function in the entry and start system is the same as that of the wireless door lock control system. However, the receiver in the certification ECU uses a door control receiver to perform the control.
Entry Illumination*1 When an electrical key enters the exterior actuation area of the door electrical key antenna, or outside electrical key antenna each interior light and power switch illumination light will illuminate.
Entry Unlock*1 The doors are unlocked by grabbing the door outside handle or pressing the back door opener switch while carrying the electrical key.
·

The driver door outside handle unlocks driver door. (Driver Door Unlock Mode)

·

The driver door outside handle unlocks all doors. (All Door Unlock Mode)

·

The front passenger door outside handle unlocks all doors.

·

The back door opener switch unlocks all doors.


Entry Lock*1 All doors are locked by touching the lock sensor of the driver, front passenger door outside handle or by pressing the lock switch of the back door while carrying the electrical key.
Reserve Lock Function*2 When a door other than the back door is closed and the door lock is operated by lock sensor of door outside handle within the exterior actuation area during auto close operation, a door lock operation is performed at that time. The door lock operation completes when the back door close operation ends.
Hands Free Power Back Door*3 The back door is opened or closed by performing the touchless kick actuation operation while carrying the electrical key.
Answer Back*1 The wireless door lock buzzer sounds*4 and the hazard warning lights blink once while locking and twice while unlocking when the doors are being locked or unlocked. Also, the answer back function operates when the doors are locked by the automatic relock function.
Automatic Relock*1 If none of the doors are opened within 30 seconds*5 or 60 seconds*6 after they are unlocked using the entry unlock operation, all the doors will be locked again automatically.
Door Open Operation Prohibition*1 Prohibits the use of entry lock operations to lock the door when any door is ajar or open.
Prevention of Key Confinement*1 Prevents the vehicle from being locked with an electrical key left inside it. This function operates in 2 different situations: when the lock switch on the door control switch is used (keyless lock) and when an entry lock operation is performed to lock the vehicle.
Start Changes the power source or starts the hybrid system.
Immobiliser Only permits the electrical key registered with the vehicle to start the hybrid system, preventing unauthorized starting of the system.
Warning The entry and start system causes the certification ECU to sound the buzzer in the combination meter assembly and uses the multi-information display in order to alert the driver.
Battery Saving
·

Suppresses auxiliary battery level drops when the vehicle is not used for a long period of time by extending the interval between or stopping each periodic transmission of the request signal and restricting the entry function.*1

·

When the electrical key is in an exterior actuation area for approximately 10 minutes or more, periodic transmission of the request signal is stopped to suppress key battery level drops.*1

·

Puts the electrical key in the sleep condition to suppress key battery level drops.*1

·

When the unlock button is pressed 2 times while pressing the lock button of the electrical key, the electrical key stops waiting on standby to receive electrical waves, suppressing key battery level drops.


Entry Unlock Mode Switching*1 Allows switching between 2 modes that can be operated with the entry unlock function.
·

Driver Door Unlock Mode

·

All Door Unlock Mode


Key Cancel The following key functions can be canceled by following certain procedures:
·

Entry unlock/lock*1

·

Hands free power back door*3

·

Prevention of key confinement*1

·

Start

·

Warning


Key Code Registration A total of 7 keys can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU.
Customization Allows the user to change settings as desired. Refer to the Repair Manual for details.



SYSTEM CONTROL


a.

Entry Unlock Function (Models with Entry Function)

i.

When the electrical key is in the actuation area formed by the door electrical key antenna, holding the door outside handle of the driver seat and touching the built-in touch sensor unlocks the driver door only. Continuing to touch the built-in touch sensor for 2 seconds or more unlocks all the doors. And holding any of the front passenger door outside handles and touching the built-in touch sensor unlocks all the doors. (Driver door unlock mode)


ii.

When the electrical key is in the actuation area formed by the door electrical key antenna, holding any of the door outside handles and touching the built-in touch sensor unlocks all the doors. (All door unlock mode)


iii.

After the doors have been unlocked, the wireless door lock buzzer sounds twice* as an answer back and the hazard lights flash twice at the same time.

*: Models with answer back buzzer function


HINT:

If the doors are locked by wireless door lock operation, the entry and start system or key linked power door lock operation, it may not be possible to unlock the doors using the entry and start system. In this situation, use the wireless door lock function of the electrical key to unlock the doors.


NOTICE:
·

When the user quickly performs an unlock operation or abruptly enters the exterior actuation area to perform an unlock operation and is unable to unlock the doors, an unlock operation needs to be performed again. When an unlock operation is performed while wearing gloves, the door may not unlock.

·

If another electrical key is in the exterior actuation area, the time it takes to unlock the door(s) after the unlock operation may be slightly longer than usual.

·

After the doors are locked, the doors cannot be unlocked for approximately 3 seconds.

·

When a wireless door lock, manual door lock or key-linked door lock operation is performed with an electrical key in the interior actuation area or near the vehicle, the entry unlock function may not operate. In this case, it is possible to unlock the doors by performing a wireless door unlock operation.



Y226694C01
5.052,2.229 5.219,0.479 true 5.156,0.271 5.469,0.427 0.313,0.156 10 false *1
*1 Unlock Sensor - -



iv.

When the electrical key is in the actuation area surrounding the back door, pressing the back door opener switch will unlock all the doors.

Y226695C01
4.813,1.823 5.656,1.219 true 2.125,1.448 1.75,0.771 true 5.656,1.083 5.969,1.24 0.313,0.156 10 false *2 1.656,0.615 1.969,0.771 0.313,0.156 10 false *1
*1 Back Door Opener Switch Assembly *2 Back Door Opener Switch




b.

Entry Lock Function (Models with Entry Function)

i.

When the electrical key is in any of the exterior actuation areas, all the doors are locked by touching the lock sensor of the front door outside handle.


ii.

After the doors have been locked, the wireless door lock buzzer sounds once* as an answer back and the hazard lights flash once at the same time.

*: Models with answer back buzzer function



iii.

If the doors do not lock when the lock sensor on the topside of a door outside handle is touched, touch the lock sensors on the top and bottom sides simultaneously by pinching the handle.

Y226696C01
4.458,2.125 5.281,0.448 5.281,0.448 4.563,2.323 true 5.229,0.25 5.542,0.406 0.313,0.156 10 false *1
*1 Lock Sensor - -



iv.

When the electrical key is in the actuation area surrounding the back door, pressing the lock switch of the back door will lock all the doors.

Y226697C01
2.135,1.458 1.813,0.792 true 5.125,1.979 5.802,1.479 true 1.729,0.646 2.042,0.802 0.313,0.156 10 false *1 5.854,1.344 6.167,1.5 0.313,0.156 10 false *2
*1 Back Door Opener Switch Assembly *2 Lock Switch




c.

Reserve Lock Function (Models with Power Back Door System)

i.

When a door other than the power back door is closed and the door lock is operated by lock sensor of door outside handle within the exterior actuation area during back door auto close operation, a door lock operation is performed at that time. The door lock operation completes when the back door close operation ends.



d.

Hands Free Power Back Door Function (Models with Hands Free Power Back Door)

i.

When the electrical key is in the actuation area surrounding the back door, performing a touchless kick actuation operation towards the center of the rear bumper will open or close the back door.

Y226698C01
3.667,2.938 3.094,1.219 true 5.76,2.74 5.052,2.313 true 4.115,3.927 3.979,3.667 true 3.802,4.042 3.698,3.75 true 3,1.031 3.313,1.188 0.313,0.156 10 false *1 4.115,3.948 4.427,4.104 0.313,0.156 10 false *b 3.75,4.063 4.063,4.219 0.313,0.156 10 false *c 5.781,2.75 6.094,2.906 0.313,0.156 10 false *2 4.75,4.24 5.063,4.396 0.313,0.156 10 false *a 3.063,3.479 3.375,3.635 0.313,0.156 10 false *d
*1 Kick Door Control Sensor *2 Electrical Key (Electrical Key Transmitter Sub-assembly)
*a The user carrying an electrical key stands around the center of the rear bumper while maintaining a certain distance (approximately equal to the length of the arm) from the rear bumper. *b The user waves a foot within approximately 100 mm (3.94 in.) from the surface of the rear bumper.
*c The user moves the foot away from the surface of the rear bumper. *d Approximately 100 mm (3.94 in.)




e.

Start Function

i.

The start function has different power source change patterns to suit the brake pedal state and shift lever position.

Pattern Brake Pedal Shift Lever Position Power Source Change Pattern
A Depressed P When the power switch is pushed once.
·

Off → READY


B Not Depressed P Each time the power switch is pushed.
·

Off → On (ACC) → On (IG) → Off


C Except P Each time the power switch is pushed.
·

Off → On (ACC) → On (IG) → On (ACC)


D - P When the power switch is pushed in the on (IG) condition.
·

On (IG) (hybrid system is started or not started) → Off


E - Except P When the power switch is pushed in the on (IG) condition.
·

On (IG) (hybrid system is started or not started) → On (ACC)



Transition of Power Source Modes
Y218338E02
0.208,0.583 1.531,0.823 1.323,0.24 10 false Shift Lever Position 0.583,0.979 1.24,1.229 0.656,0.25 10 false Pattern 0.375,1.375 1.406,1.583 1.031,0.208 10 false Power Switch 0.417,1.771 1.281,2.021 0.865,0.25 10 false Brake Pedal 0.625,2.177 1.229,2.438 0.604,0.26 10 false Time 0.104,3.146 0.563,3.688 0.458,0.542 10 false Power Source 0.948,2.615 1.302,2.823 0.354,0.208 10 false Off 0.771,3.01 1.51,3.271 0.74,0.26 10 false On (ACC) 0.823,3.417 1.531,3.677 0.708,0.26 10 false On (IG) 0.813,3.823 1.448,4.073 0.635,0.25 10 false READY 3.333,0.573 3.802,0.813 0.469,0.24 10 false P 5.823,0.573 6.583,0.854 0.76,0.281 10 false Except P 1.917,0.979 2.677,1.26 0.76,0.281 10 false B or D 3.25,0.979 4.01,1.26 0.76,0.281 10 false A or D 1.885,1.375 2.646,1.656 0.76,0.281 10 false Pushed 3.104,1.792 3.865,2.073 0.76,0.281 10 false Depressed 5.406,0.969 6.167,1.25 0.76,0.281 10 false C or E 4.615,0.948 5.031,1.188 0.417,0.24 10 false - 4.625,1.365 5.042,1.604 0.417,0.24 10 false - 4.625,1.75 5.042,1.99 0.417,0.24 10 false - 5.573,1.75 5.99,1.99 0.417,0.24 10 false - 6.521,0.958 6.938,1.198 0.417,0.24 10 false - 6.229,1.792 6.99,2.073 0.76,0.281 10 false Depressed 5.563,2.167 5.979,2.406 0.417,0.24 10 false - 6.552,2.167 6.969,2.406 0.417,0.24 10 false - 2.063,1.75 2.479,1.99 0.417,0.24 10 false - 2.063,2.167 2.479,2.406 0.417,0.24 10 false - 3.396,2.167 3.813,2.406 0.417,0.24 10 false - 4.25,2.188 4.51,2.417 0.26,0.229 10 false *1 4.563,2.188 4.823,2.417 0.26,0.229 10 false *2 4.885,2.188 5.146,2.417 0.26,0.229 10 false *3 3.208,1.385 3.969,1.667 0.76,0.281 10 false Pushed 5.365,1.385 6.125,1.667 0.76,0.281 10 false Pushed 6.323,1.385 7.083,1.667 0.76,0.281 10 false Pushed 5.542,3.042 5.802,3.271 0.26,0.229 10 false # 5.844,3.042 6.104,3.271 0.26,0.229 10 false # 6.813,3.031 7.073,3.26 0.26,0.229 10 false # 0.646,4.417 2.479,4.615 1.833,0.198 10 false : Transition 0.635,4.813 3.719,5.063 3.083,0.25 10 false : Only when key certification is OK. 0.656,5.198 6.531,5.865 5.875,0.667 10 false : Only when the vehicle is stopped. (While driving, if the power switch is pressed for 2 seconds or more or pressed 3 times or more in a row, the hybrid system is stopped and the power source mode changes to on (ACC).) 0.646,6.146 6.906,6.552 6.26,0.406 10 false : Power source transition to off is possible only when the power source mode has changed to on (ACC), such as the power source transition indicated by #, and the shift lever has been moved to P. 0.313,6.833 3.396,7.083 3.083,0.25 10 false *1: Not operated for 20 minutes 0.313,7.167 2.729,7.417 2.417,0.25 10 false *2: Not operated for 1 hour 0.313,7.5 5.146,7.75 4.833,0.25 10 false *3: Power source turned off according to hybrid system request


ii.

Transition of the power source mode when the electrical key battery is low or the electrical key is not operating normally due to an electromagnetic interference is as follows:

1.

The driver uses the mechanical key to unlock the door and enters the vehicle while carrying the electrical key.

2.

The driver places the TOYOTA mark of the electrical key in contact with the front of the power switch while depressing the brake pedal.

3.

Within approximately 10 seconds after the buzzer sounds in the combination meter, the driver releases the brake pedal and presses the power switch.

4.

With each pressing of the power switch, the power source mode changes as follows: off → on (ACC) → on (IG) → off.



iii.

When starting the hybrid system while the electrical key battery is low or the electrical key is not operating normally due to an electromagnetic interference:

1.

The driver uses the mechanical key to unlock the door and enters the vehicle while carrying the electrical key.

2.

The driver places the TOYOTA mark of the electrical key in contact with the front of the power switch while depressing the brake pedal when the shift lever is in P.

3.

Within approximately 10 seconds after the buzzer sounds and the entry warning display illuminates, the driver presses the power switch while depressing the brake pedal.

4.

Pressing the power switch starts the hybrid system.


NOTICE:
·

Normally, the operation of the power switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the power switch for approximately 2 seconds or more or pushing the power switch 3 times or more in a row, the driver can stop the hybrid system when the vehicle is in motion.

·

If no signals are transmitted to the certification ECU due to malfunctions in the stop light switch assembly, the hybrid system may not start when the power switch is pushed with the brake pedal depressed. In such cases, performing the following procedure may enable the hybrid system to start: 1) push the power switch to turn the power source from off to on (ACC), and 2) push the power switch again and hold it for 15 seconds or more.

·

The above 2 operations must be applied only in emergency situations. Under normal conditions, the hybrid system must not be stopped by pushing the power switch while driving. Also, it should not be started without depressing the brake pedal or when the shift lever is in any position other than P or N.





f.

Warning

i.

When any of the situations below occur, the entry and start system sounds the wireless door lock buzzer and a buzzer in the combination meter assembly and displays a message on the multi-information display in order to alert the driver.

Situation Condition
A The hybrid system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
B The hybrid system is left running and the shift lever is in P when the driver gets out of the vehicle.
C The hybrid system is left running when a passenger gets out of the vehicle while holding the electrical key.
D The electrical key is not within the actuation areas.
E The vehicle is driven without an electrical key.
F The electrical key is left in the vehicle.
G A door is ajar.
H The key reminder sounds.
I The key battery is weak.
J Steering lock does not release.
K A malfunction has been detected in a vehicle speed signal, etc.
L The hybrid system cannot be started (system/driver error).
M Immobiliser system certification confirmation occurs.
N An electrical key has been registered to the vehicle.
O Hybrid system start operation guide on (ACC)
P Hybrid system start operation guide on (IG)
Q The power switch cannot be turned off (shift lever in any position except P).
R The power switch cannot be turned off (shift lever in P).
S Auto power off operation occurs.
T Hybrid system emergency stop operation is performed.
U The user performed an emergency engine stop while driving.
V Power switch is operated while driving.
W Power switch is operated while driving.
X While the vehicle is stationary, the shift lever is moved to a position other than P or N with the power switch on (IG) and the hybrid system stopped.
Y While the vehicle is stationary, with a shift position N selected, the power switch on (IG) and the hybrid system stopped.
Z The vehicle started to roll away with the power switch on (IG) and the hybrid system stopped.
AA Accessory state
AB Ignition on state


ii.

Situation A

There are 2 patterns for situation A.

Pattern 1:

When the shift lever is in a position other than P, the power switch is in a mode other than off and the driver opens the door and attempts to get out of the vehicle, the following control is performed:

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away (Vehicle creep, such as when N is selected)
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (ACC) or on (IG).

·

The shift lever is in any position except P.

·

The driver door is opened.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

Shift to P when Parked


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power switch is turned off.

·

The shift lever is moved to P.

·

The driver door is closed.

·

The vehicle speed is above 5 km/h (3 mph).



Pattern 2:

Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (ACC) or on (IG).

·

The shift lever is in any position except P.

·

The driver door is opened → closed.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display The following warning messages are alternately displayed:
·

Shift to P when Parked

·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously
Buzzer and Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power switch is turned off.

·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is detected in the vehicle (interior key certification result is OK).


"Shift to P when Parked" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power switch is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





iii.

Situation B

There are 3 patterns for situation B.

Pattern 1:

When the shift lever is in P and the power switch is in a mode other than off (the steering remains unlocked), the driver door is opened and the driver attempts to leave the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition Condition 1
The warning is activated when both of the following conditions are met:
·

The power switch is on (ACC).

·

The driver door is open.


Condition 2
The warning is activated when all of the following conditions are met for 1 second:
·

The power switch is turned off.

·

The steering lock remains unlocked.

·

The driver door is open.


Warning Method Combination Meter Assembly Buzzer Sounds continuously at short and even intervals
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power switch is turned on (IG).

·

The driver door is closed.

·

The power switch is turned off and the steering wheel lock control is performed.



Pattern 2:

Under the situation of pattern 1, the driver opens and closes the driver door and attempts to leave the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (ACC) or on (IG).

·

The shift lever is in P.

·

The driver door is opened → closed.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds 3 times
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power switch is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).



Pattern 3:

Under the situation of pattern 2, the driver touches the lock sensor on the door outside handle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (ACC) or on (IG).

·

The shift lever is in P.

·

The electrical key is not detected in the vehicle (interior key certification fails), but detected in an outside detection area (exterior key certification result is OK).

·

The lock sensor on the door outside handle is on (touched).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning messages are alternately displayed:
·

Turn Power OFF

·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power switch is turned off.

·

The shift lever is moved to any position except P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is detected in the vehicle (interior key certification result is OK).

·

Any door is opened or closed.


"Turn Power OFF" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The power switch is turned off.

·

The shift lever is moved to any position except P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power switch is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





iv.

Situation C

When the hybrid system is left running, a passenger leaves the vehicle while holding the electrical key. In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (ACC) or on (IG).

·

A door other than the driver door is opened → closed.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer Sounds 3 times
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power switch is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





v.

Situation D

When the electrical key is not in the vehicle, the driver attempts to turn the power switch on (IG) (emergency key operation* is included). In this situation, the following control is performed:

*: Emergency key operation is an operation that changes the power source by touching the power switch with the electrical key.

Possible Effects without Warning User becomes confused
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The immobiliser system is set.

·

The electrical key is not in the vehicle (interior key certification fails and transponder certification fails).

·

No records of unlock operation using a mechanical key and key certification failure when the power switch was turned on (IG).


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

15 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since a door was opened using a door outside handle.





vi.

Situation E

The vehicle starts moving without a registered electrical key in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is on (IG).

·

The warning is activated in situation C.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key is not detected in the vehicle (interior key certification fails).


Warning Method Combination Meter Assembly Buzzer Sounds 9 times
Multi-information Display The following warning message is displayed:
·

Key Not Detected Check Key Location


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power switch is turned off.

·

The electrical key is detected in the vehicle (interior key certification result is OK).





vii.

Situation F

The lock sensor on a door outside handle is touched to perform entry lock with the electrical key left in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is off.

·

All doors are closed.

·

The electrical key is detected in the vehicle (interior key certification result is OK).

·

The lock sensor on the door outside handle is on (touched).

·

Any door is unlocked.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Key Detected in Vehicle


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

5 seconds elapse.

·

The power switch is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Any door is opened.

·

Lock operation is detected.


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

60 seconds elapse.

·

The power switch is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Lock operation is detected.





viii.

Situation G

The lock sensor on the door outside handle is pushed to perform entry lock, however, a door is ajar. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is off.

·

Any door is open other than the door where the entry lock operation is performed.

·

The lock sensor on the door outside handle is on (touched), the lock switch on the electrical key or the back door lock switch is pressed.

·

The electrical key is in an outside detection area (exterior key certification result is OK).


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer Sounds continuously
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power switch is turned on (ACC) or on (IG).

·

All doors are closed.

·

Unlock operation is performed using the wireless door lock control function.

·

Unlock operation is performed using the touch sensor on the inside of a door outside handle.





ix.

Situation H

The door is locked with the electrical key left in the vehicle. In this situation, the following control is performed:

*: Keyless lock operation is door lock operation without using the electrical key. First, set the lock position (door lock knob) when the door is open, and close the door while pulling the door outside handle to lock the door.

Possible Effects without Warning Vehicle theft
Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The door is locked using the keyless lock operation.*

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2
The warning is activated when all of the following conditions are met (Models compliant with Thatcham only):
·

The power switch is turned off.

·

All doors are closed and locked.

·

Lock operation without using the entry system is detected.

·

The electrical key is in the vehicle (interior key certification result is OK).


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Detected in Vehicle


Advisory Display -
Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power switch is turned to other mode.

·

Any door is opened.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The power switch is turned to another mode.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).





x.

Situation I

The vehicle is driven using an electrical key that has a low battery. In this situation, the following control is performed:

*: Warning performed after 20 minutes of the power switch being turned on (IG)

Possible Effects without Warning Usability function, hybrid system cannot be restarted
Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The power switch is turned off after being left on (IG) for more than 20 minutes.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2
The warning is activated when all of the following conditions are met:
·

The hybrid system is stopped → restarted.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.

·

The low key battery warning for condition 1 was performed.*


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Key Battery Low Replace Key Battery


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The vehicle speed is above 5 km/h (3 mph).





xi.

Situation J

The steering lock cannot be released or the shift lever is moved to a position other than P before the steering lock is unlocked. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the following condition is met:
The steering lock cannot be released (the steering lock ECU judgment).
Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Push Power Switch while Turning Steering Wheel in Either Direction


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The power switch is pushed while the steering wheel is turned left and right.
The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The steering lock is released.





xii.

Situation K

A vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation has been detected. In this situation, the following control is performed:

Possible Effects without Warning Malfunction Detection
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The steering lock ECU (steering lock actuator assembly) or steering lock/unlock position switch is malfunctioning.

·

The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Smart Entry & Start System Malfunction See Owner's Manual


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The system returns to normal.





xiii.

Situation L

When the driver attempts to start the hybrid system after unlocking the driver door using the mechanical key, the electrical key cannot be detected in the vehicle or cannot be detected in the vehicle 2 times in a row. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the power switch is pressed with all of the following conditions met:
·

The immobiliser system is set.

·

The electrical key is not detected in the vehicle (interior key certification fails).

·

The doors were unlocked using a mechanical key or when the power switch is pressed, a certification error occurs 2 times in a row.


Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed for 60 seconds (and then automatically turned off):
·

Press Brake Pedal and Touch Power Switch with Key


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification result is OK and transponder certification result is OK.).

·

30 seconds have elapsed since the door was opened using a door outside handle.





xiv.

Situation M

The power switch is touched with an electrical key when the key battery voltage is low, smart operation is canceled or radio interference occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition Transponder certification result is OK.
Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

10 seconds elapse.

·

The electrical key is detected in the vehicle (interior key certification results is OK).

·

The hybrid system is started.

·

The immobiliser system is set and interior certification is stopped or key certification fails.





xv.

Situation N

An electrical key has been registered to the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The power switch is turned off.

·

The driver door is unlocked by an unlock operation from the outside of the vehicle, and then opened.


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

A New Key has been Registered Contact Your Dealer for Details


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds have elapsed since the warning started.

·

10 days have elapsed since the warning was first displayed.

·

All doors are closed and locked.

·

The power switch is turned on (IG).





xvi.

Situation O

The system recognizes the situation that indicates the driver may start the hybrid system (when the driver enters the vehicle or the power switch is on (ACC)). In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted
Warning Active Condition The warning is activated when either of the following conditions is met:
·

When the door is unlocked from the outside of the vehicle with the power switch off, the driver door is closed → opened.

·

Each time the power source mode is changed from off to on (ACC) without the brake pedal depressed.


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

19 seconds have elapsed since the warning started.

·

The hybrid system is started.

·

Door lock operation is performed from the outside of the vehicle.

·

Wireless operation is performed from the inside of the vehicle or door lock operation is performed using a keyless lock function.





xvii.

Situation P

The system recognizes the situation that indicates the driver may start the hybrid system (when the power switch is on (IG)). In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted
Warning Active Condition The warning is activated when either of the following conditions is met:
·

Each time the power source mode is changed from off to on (IG) (the hybrid system is not started) with the shift lever in P and without the brake pedal depressed.

·

When the power switch is on (IG) (the hybrid system is not started) with the shift lever in a position other than P, the shift lever is moved to P.


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Not Ready to Drive Press Brake Pedal and Push Power Switch to Start


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source mode is changed to any mode other than on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

The shift lever is in a position other than P.





xviii.

Situation Q

The driver attempts to turn the power switch off with the shift lever in any position other than P. In this situation, the following control is performed:

Possible Effects without Warning Discharged auxiliary battery, vehicle roll-away.
Warning Active Condition The power switch is turned off when the shift lever in a position other than P. (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.)
Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Shift to P when Parked


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift lever is moved to P.

·

The power switch is turned to a mode other than on (ACC).





xix.

Situation R

Under situation Q, the shift lever is moved to P. In this situation, the following control is performed:

Possible Effects without Warning Discharged auxiliary battery, vehicle roll-away.
Warning Active Condition The shift lever is moved to P.
Warning Method Combination Meter Assembly Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

Turn Power OFF


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source mode is changed to a mode other than on (ACC).

·

The shift lever is in any position other than P.





xx.

Situation S

Automatic power off operation occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The shift lever is in P.

·

The power switch is on (ACC) or on (IG).

·

The vehicle speed is not detected and the hybrid system is stopped.

·

The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the power switch on (ACC) or for 1 hour with the power switch on (IG)).


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Auto Power OFF to Conserve Battery


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds have elapsed since the warning started.

·

The power switch is turned on (ACC) or on (IG).





xxi.

Situation T

The driver stopped the hybrid system using emergency operation while driving. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The hybrid system is stopped by emergency stop operation while driving.

·

After emergency stop operation, the power switch is turned on (IG), the vehicle speed is detected and the hybrid system is not started.


Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Shift to N and Push POWER Switch to Restart


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift lever is moved to P.

·

The vehicle speed is not detected (after the power switch is turned on (IG) using power switch operation).

·

The power switch is operated.

·

The hybrid system has started.





xxii.

Situation U

The user performed an emergency hybrid system stop while driving. In this situation, the following control is performed:

Possible Effects without Warning The driver may not notice that the hybrid system has been stopped while driving.
Warning Active Condition The hybrid system is stopped using the emergency engine stop function.
Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift lever is moved to P.

·

The vehicle speed is not detected (after the power switch is turned on (IG) using power switch operation).

·

The hybrid system has started.





xxiii.

Situation V

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Wrong operation is prevented
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Buzzer Sounds intermittently
Multi-information Display -
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

1.8 seconds have elapsed since the power switch operation was stopped.

·

The power switch is turned off.





xxiv.

Situation W

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

Push and Hold Power Switch for Emergency Stop


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds elapse.

·

The power switch is turned off.





xxv.

Situation X

While the vehicle is stationary and a shift position other than P or N selected, the power switch on (IG) and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is stopped and a shift position other than P or N selected, the power switch on (IG).
Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

Hybrid System Stopped Shift into P


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift lever is moved to P or N.

·

The power switch is turned off.

·

The vehicle speed is detected.





xxvi.

Situation Y

While the vehicle is stationary, the shift lever is moved to a position N with the power switch on (IG) and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition While the vehicle is stopped, the shift lever is moved to a position N with the power switch on (IG).
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display Shift into P to Start
Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift lever is moved to other than N.

·

The power switch is turned off.

·

The vehicle speed is detected.





xxvii.

Situation Z

The vehicle started to roll away with the power switch on (IG) and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is moving, the shift lever is in a position other than P or N with the power switch on (IG) and the hybrid system stopped.
Warning Method Combination Meter Assembly Buzzer Sounds intermittently
Multi-information Display The following warning message is displayed:
·

Hybrid System Stopped Stop in a Safe Place


Advisory Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift position is changed to N.

·

The power switch is turned off.

·

The hybrid system has started.

·

The vehicle speed is not detected.





xxviii.

Situation AA

The power source is changed to on (ACC). In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (ACC).
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display -
Advisory Display ACCESSORY
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when the following condition is met:
·

The power source is changed to a mode other than on (ACC).





xxix.

Situation AB

The power source is changed to on (IG). In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (IG).
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display -
Advisory Display IGNITION ON
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is changed to a mode other than on (IG).

·

The display in the odometer area is changed due to user operation.






g.

Auxiliary Battery Saving Function

i.

Battery saving preserves the vehicle and electrical key batteries. The auxiliary battery saving function is activated when the vehicle remains parked for a long time and when the electrical key is left in the exterior actuation area.

Condition Condition Outline
When the vehicle remains parked for a long time. Condition 1:
No response from the electrical key for more than 5 days.
·

Door electrical key antennas and outside electrical key antenna stop emitting signals for creating the actuation area. In addition, the lock sensors or unlock sensors of all the seats are available, so touching the sensor can lock or unlock.


When the power switch is turned on (IG), the control is canceled and the system is returned to normal.
Condition 2:
No response from the electrical key for more than 14 days.
·

Door electrical key antennas and outside electrical key antenna stop emitting signals for creating the actuation area.

·

The lock sensors and unlock sensors except for the driver door are disabled.


When the power switch is turned on (IG), the control is canceled and the system is returned to normal. When one of the following conditions is met, the control is returned to condition 1:
·

The doors are locked or unlocked using the wireless door lock control function.

·

The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.

·

A door is locked or unlocked using the mechanical key.

·

Door is opened → closed.


When the electrical key is left in the exterior actuation area. This state continues longer than 10 minutes.
·

Electrical key antenna that is detecting the electrical key stops emitting signals for creating the actuation area.


The control is stopped when one of the following conditions is met:
·

The doors are locked or unlocked using the wireless door lock control function.

·

The doors are locked or unlocked by touching the lock/unlock sensor.

·

A door is locked or unlocked using the mechanical key.




ii.

In addition to the above functions, the auto power off function helps to reduce drain on the auxiliary battery by turning the power source mode to off when approximately 60 minutes have elapsed since the shift lever was moved to P with the power source on (ACC), or the hybrid system was turned off with the shift lever in P, the power source on (IG) and the vehicle stationary.



h.

Key Battery Saving Function

i.

This function cancels the signal reception waiting state of the electrical key, reducing the consumption of current from its battery.


ii.

The electrical key can be placed into and taken out of battery saving mode. When the electrical key is in battery saving mode, the entry and start system will not be able to detect the electrical key, as the electrical key will not respond to signals from the vehicle. The entry and start system will not operate if the electrical key is in battery saving mode.


iii.

Pressing the unlock button of the electrical key twice while pressing the lock button (the indicator light of the electrical key blinks 4 times) selects battery saving mode for the electrical key.


iv.

Battery saving mode can be canceled by pressing any button on the electrical key.



i.

Entry Unlock Mode Switching Function

i.

The following entry unlock modes can be selected when using the entry unlock mode switching function.

·

All door unlock mode: When the sensor of a door outside handle is touched, an entry unlock operation is performed simultaneously for all doors.

·

Driver door unlock mode: When the sensor of the driver side door outside handle is touched, an entry unlock operation is performed for the driver door only. If any other door outside handle is touched, an entry unlock operation is performed simultaneously for all doors.



ii.

When customizing through manual operation:

1.

Turn the power switch off.

2.

Check that the LED of the electrical key is not illuminated, and then press and hold the lock and unlock buttons of the electrical key for 5 seconds or more while the electrical key is in the actuation area.

3.

Check the current setting.

HINT:
·

The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

·

The answer back (wireless door lock buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below:

Currently Selected Mode Answer Back (Wireless Door Lock Buzzer) Answer Back (Buzzer in Combination Meter Assembly)
All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once



4.

Release the lock and unlock switches of the electrical key.

5.

Check that the LED of the electrical key is not illuminated, and then press and hold the lock and unlock switches of the electrical key for 5 seconds or more to change the mode.

HINT:

Repeat the procedure as necessary to select the desired mode.


6.

Unlock the doors with the wireless operation, and then open any door.

Y226803E01
4.583,0.333 6.5,0.667 1.917,0.333 10 false Combination Meter Assembly 6.333,0.917 6.833,1.25 0.5,0.333 10 false Buzzer 4.167,0.917 5.75,1.25 1.583,0.333 10 false Multi-information Display 6.083,2.417 6.917,2.75 0.833,0.333 10 false Sounds once 4,1.75 5.917,2.083 1.917,0.333 10 false Driver door "OPEN" indication 4.167,2.917 5.917,3.25 1.75,0.333 10 false All door "OPEN" indication 1.667,0.583 3.417,0.917 1.75,0.333 10 false Wireless Door Lock Buzzer 1.583,1.708 1.917,2.042 0.333,0.333 10 false ON 1.5,2.042 1.833,2.375 0.333,0.333 10 false OFF 2.167,1.479 3.167,1.813 1,0.333 10 false Sounds 3 times 2.167,2.583 3.25,2.917 1.083,0.333 10 false Sounds 2 times 0.25,1.5 1,2.5 0.75,1 10 false Driver Door Unlock Mode 0.333,2.667 0.917,3.667 0.583,1 10 false All Door Unlock Mode 1.75,3.188 2.083,3.521 0.333,0.333 10 false OFF 1.833,2.854 2.167,3.188 0.333,0.333 10 false ON




j.

Key Cancel Function

i.

The following system functions can be deactivated by using the key cancel procedure:

·

Entry Lock*1

·

Entry Unlock*1

·

Hands Free Power Back Door*2

·

Prevention of Key Confinement*1

·

Start

·

Warning

*1: Models with entry function

*2: Models with hands free power back door




ii.

The system functions can be deactivated by using the following key cancel procedure when the power switch is off and the driver door is closed and unlocked:

Key Cancel Procedure

The procedure is as follows:

-

Press the unlock button of the electrical key once.

-

Within 5 seconds of the step above, open the driver door (driver door: close → open).

-

Within 5 seconds of the step above, press the unlock button of the electrical key twice.

-

Repeat close → open for the driver door twice* (driver door: open → close → open → close → open).

-

Press the unlock button of the electrical key twice.*

-

Repeat close → open for the driver door once* (driver door: open → close → open).

-

Within 5 seconds of the step above, close the driver door.


When the cancel procedure is complete, the buzzer sounds twice. Meanwhile, when the procedure is performed again to resume the system, the buzzer sounds once.



HINT:

*: All these 3 steps are performed within 30 seconds of the previous step.




k.

Key Code Registration Function

i.

The table below shows the 3 special ID code registration function modes through which up to 7 different transmitter recognition codes can be registered. For details, refer to the Repair Manual.

Mode Function
Rewrite Clears all previously registered codes and registers only the newly received codes. This mode is used whenever the certification ECU is replaced.
Add Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter.
Confirm Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.




DIAGNOSIS


a.

The certification ECU can detect malfunctions in the entry and start system when the power source is on (IG).


b.

When the ECU detects a malfunction, a message is displayed on the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.


c.

The indicator light warning continues for 15 seconds even after the power switch is turned off.


d.

The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.


e.

The entry and start system may not operate successfully if a malfunction occurs.