FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: If the setting of the wireless one motion function is not turned ON by the customization. *2: Models with hands free power back door *3: Models with power back door answer back hazard warning light function *4: HV models *5: Gasoline models |
||
| Power Back Door Unit Assembly Set LH | Power Back Door Motor | Opens and closes the back door when actuated by the power back door ECU. |
| Hall IC | Detects the operation conditions of the back door and outputs a pulse signal to the power back door ECU. | |
| Power Back Door Unit Assembly Set RH | Power Back Door Motor | Opens and closes the back door when actuated by the power back door ECU. |
| Hall IC | Detects the operation conditions of the back door and outputs a pulse signal to the power back door ECU. | |
| Back Door Lock with Courtesy Light Switch Assembly | Back Door Lock Motor | Latches and unlatches the back door when actuated by the power back door ECU. |
| Sector Switch | Detects the initial position of the back door lock motor and outputs a signal to the power back door ECU. | |
| Pawl Switch | Detects whether the ratchet condition is released or engaged and outputs a signal to the power back door ECU. | |
| Latch Switch | Detects whether the back door is open or ajar (half-latch) and outputs a signal to the power back door ECU. | |
| Courtesy Switch | Detects whether the back door is ajar (half-latch) or fully closed (full-latch) and outputs a signal to the power back door ECU. | |
| Power Back Door Switch (Power Back Door Control Switch) | ·
Outputs signals to the main body ECU. ·
When the back door is unlocked and closed, back door opening operations are performed by pressing and holding the power back door switch. ·
When the back door is open, back door closing operations are performed by pressing and holding the power back door switch. ·
During an opening or closing operation of the back door, pressing the power back door switch suspends the operation. ·
After the opening or closing operation of the back door is suspended, pressing and holding the power back door switch causes the back door to operate in the opposite direction. |
|
| Back Door Opener Switch Assembly
·
Back Door Opener Switch |
·
Outputs signals to the certification ECU. ·
When the back door is closed or after the opening or closing operation is suspended, back door opening operations are performed by pressing the back door opener switch. ·
By pressing the back door opener switch during the back door opening or closing operation, the back door stops the operation. |
|
| Back Door Switch (No. 1 Power Back Door Control Switch) | ·
Outputs signals to the power back door ECU. ·
When the back door is open, back door closing operations are performed by pressing and then releasing the back door switch. ·
During an opening or closing operation of the back door, pressing the back door switch suspends the operation. ·
After the opening or closing operation of the back door is suspended, pressing and then releasing the back door switch causes the back door to operate in the opposite direction. ·
After the opening or closing operation of the back door is suspended, by pressing and holding the back door switch, the power back door ECU activates the memory function. |
|
| Electrical Key (Electrical Key Transmitter Sub-assembly)
·
Power Back Door Button |
·
Transmits signals to the door control receiver. ·
When the back door is unlocked*1 and closed, back door opening operations are performed by pressing and holding the power back door button. ·
When the back door is open, back door closing operations are performed by pressing and holding the power back door button. ·
During an opening or closing operation of the back door, pressing the power back door button suspends the operation. ·
After the opening or closing operation of the back door is suspended, pressing and holding the power back door button causes the back door to operate in the opposite direction. |
|
| Kick Door Control Sensor*2 | ·
Detects touchless kick actuation operations and outputs signals to the power back door ECU. ·
When the back door is closed, back door opening operations are performed by performing the touchless kick actuation operation. ·
When the back door is open, back door closing operations are performed by performing the touchless kick actuation operation. ·
During an opening or closing operation of the back door, performing the touchless kick actuation operation suspends the operation. ·
After the opening or closing operation of the back door is suspended, performing the touchless kick actuation operation causes the back door to operate in the opposite direction. |
|
| Touch Sensor LH (Power Back Door Sensor Assembly LH) | Detects if an object is jammed in the back door during a closing operation of the back door and outputs a signal to the power back door ECU. | |
| Touch Sensor RH (Power Back Door Sensor Assembly RH) | ||
| Power Back Door Warning Buzzer | Sounds to inform the user of the operation condition of the power back door system, and of any malfunctions in the system. | |
| Wireless Door Lock Buzzer | Sounds to inform the user that the system is starting an operation. | |
| Door Control Receiver | Receives power back door button signals and sends them to the certification ECU. | |
| Combination Meter Assembly
·
Power Back Door Main Switch |
·
Outputs power back door main switch on and off signals to the main body ECU. ·
Receives hazard warning light flash request signals and flashes the hazard warning lights.*3 |
|
| Power Back Door ECU (Multiplex Network Door ECU) | ·
Controls the power back door system in accordance with signals received from the switches, sensors and ECUs. ·
Receives signals from the Hall IC to detect the back door condition and the opening and closing speed of the back door. ·
Informs the user of the operation condition of the power back door system by sounding the power back door warning buzzer and outputs hazard warning light flash request signals to the combination meter*3. |
|
| Main Body ECU (Multiplex Network Body ECU) | ·
Sends signals from the switches and ECUs to the power back door ECU. ·
Informs the user that the system is starting an operation by sounding the wireless door lock buzzer. |
|
| Certification ECU (Smart Key ECU Assembly) | Sends back door opener switch and power back door button signals to the main body ECU. | |
| Hybrid Vehicle Control ECU*4 | Sends shift position signals to the main body ECU. | |
| ECM*5 | ||
| Brake Booster with Master Cylinder Assembly*4
·
Skid Control ECU |
Sends vehicle speed signals to the main body ECU. | |
| Brake Actuator Assembly*5
·
Skid Control ECU |
·
Sends vehicle speed signals to the main body ECU. ·
Sends parking brake operation signals to the main body ECU. |
|
| Parking Brake ECU Assembly*4 | Sends parking brake operation signals to the main body ECU. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
|
FUNCTION
| Function | Outline |
|---|---|
|
*1: Models with hands free power back door *2: If the setting of the wireless one motion function is not turned ON by the customization. |
|
| Opener Function | ·
Upon receiving an on signal from the power back door switch, back door opener switch or power back door button with the back door unlocked and closed, the power back door ECU actuates the back door lock motor to release the latch of the back door lock, and then actuates the power back door motor to open the back door. ·
Upon receiving an on signal from the power back door switch, back door switch, back door opener switch or power back door button after the closing operation is suspended, the power back door ECU actuates the power back door motor to open the back door. |
| Closer Function | Upon receiving an on signal from the power back door switch, back door switch or power back door button with the back door open or after the opening operation is suspended, the power back door ECU actuates the power back door motor to close the back door, and then actuates the back door lock motor to engage the latch of the back door lock. |
| Jam Protection Function | ·
Upon receiving signals from a touch sensor or the Hall ICs of the power back door motor, the power back door ECU detects that an object is jammed in the back door. If this occurs during an opening operation, operation of the back door is immediately suspended. If this occurs during a closing operation, the operation of the back door is suspended after moving upward a certain distance. The power back door warning buzzer sounds twice when a jammed object is detected. ·
After the back door operation is canceled by the jam protection function, the back door can be operated by pressing one of the switches. |
| Back Door Open/Close Speed Control Function | In accordance with signals received from the Hall ICs of the power back door motor, the power back door ECU performs control so as to make the opening and closing speed of the back door even. |
| Suspending Control Function | By conducting any of the following operations during an opening or closing operation of the power back door, the operation will be canceled:
·
The power back door main switch is turned off. ·
The power back door switch is pressed. ·
The back door opener switch is pressed. ·
The back door switch is pressed. ·
The power back door button is pressed. ·
The touchless kick actuation operation is performed.*1 |
| Memory Function | ·
By pressing and holding the back door switch for approximately 1.7 seconds while manually keeping the back door at the desired opening angle, the power back door warning buzzer sounds 4 times as an answer back and the power back door ECU memorizes the angle. From the next time the back door is open, the back door will stop at the set angle. ·
By pressing and holding the back door switch for approximately 7 seconds after the set angle is memorized, the memorized position is initialized. |
| Assist Function | When the back door is stopped and then manually operated in the closing direction, the power back door ECU drives the power back door motor to operate the back door until it is fully closed. |
| Customization Function | This function can be used to set the back door opening angle at 5 different positions. |
| Switch Operation Function | When one of the operation switches is operated, the following operations are performed in accordance with the back door condition:
·
When the power back door switch is pressed for approximately 0.8 seconds, an opening operation is performed if the back door is closed (or was suspended during a closing operation), and a closing operation is performed if the back door is open (or was suspended during an opening operation). ·
When the back door opener switch is pressed, an opening operation is performed. ·
When the back door switch is pressed and then released, a closing operation is performed if the back door is open (or was suspended during an opening operation), and an opening operation is performed if the back door was stopped during a closing operation. ·
When the power back door button is pressed for approximately 0.8 seconds, an opening operation is performed if the back door is unlocked*2 and closed (or was suspended during a closing operation), and a closing operation is performed if the back door is open (or was suspended during an opening operation). |
| Wireless One Motion Function | ·
When the back door button is pressed with the back door locked, the back door is unlocked and opened. ·
Although this function is disabled by default, the function can be set via the customization function. |
| Handle One Motion Function | When the power back door opener switch is pressed with the back door locked, the back door is unlocked and opened. |
| Hands Free Power Back Door Function*1 | ·
When the kick door control sensor detects a touchless kick actuation operation with the back door locked, the back door is unlocked and opened. ·
When the kick door control sensor detects a touchless kick actuation, an opening operation is performed if the back door is closed (or was suspended during a closing operation) and a closing operation is performed if the back door is open (or was suspended during an opening operation). |
If power supply is stopped such as when the battery terminals are removed, initialization is required. The back door should be fully closed with power being supplied for initialization.
SYSTEM CONTROL
Opener Function
Pressing and holding the power back door switch or power back door button for 0.8 seconds or more with the back door unlocked and closed (or after a closing operation was suspended) starts an opening operation.
When the power back door ECU detects a user operation, it sounds the wireless door lock buzzer and power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the back door lock motor in order to release the latch and then actuates the power back door motor to open the back door. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Except models with manual transaxle *4: Pulse unit |
|||
| (a) | Power Back Door Switch | Turned On (Pressed for Approximately 0.8 Seconds) | User operation is detected. |
| Power Back Door Button | |||
| (b) | Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 |
| Wireless Door Lock Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the wireless door lock buzzer sounds for approximately 0.8 seconds. | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is unlocked and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. While vehicle speed is 3 km/h (2 mph) or less, shift lever is in P*3, brake pedal is depressed or parking brake is applied. (When power source mode is on (IG).) E. User operation is detected. When conditions A, B, C, D and E listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| Back Door Lock Motor | Changes from Off to Release | Approximately 0.8 seconds after user operation is detected, the release rotation relay turns on and a release operation starts. | |
| (c) | Power Back Door Motor | Changes from Off to Opener | F. Courtesy switch is detected to be on. G. Courtesy switch and latch switch are detected to be on. H. Condition F or G listed above is not detected for approximately 1 second or more after the back door lock motor starts a release operation. When any one of the 3 conditions listed above is met while the back door lock motor is performing a release operation, the opener relay turns on and an opener operation starts. |
| (d) | Back Door Lock Motor | Changes from Release to Off | When the latch switch is detected to be on, the release rotation relay turns off and the release operation stops. |
| (e) | Back Door Lock Motor | Changes from Off to Engage | I. After the latch switch is detected to be on, the Hall ICs of the power back door motor detect a movement of 20 edges*4 in the opening direction. J. Approximately 3 seconds or more have elapsed since the back door lock motor was detected to be off. When condition I or J listed above is met, the engagement rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (f) | Back Door Lock Motor | Changes from Engage to Off | When the sector switch is detected to be on, the engagement rotation relay turns off and the reverse rotation operation stops. |
| (g) | Power Back Door Motor | Changes from Opener to Off | K. Hall ICs of the power back door motor detect a movement of 15 edges*4 in the closing direction from the fully open position. L. Power back door motor open output is detected continuously for approximately 30 seconds or more. When condition K or L listed above is met, the opener relay turns off and the opener operation stops. |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
Pressing the back door opener switch with the back door closed (or after an operation was suspended), or pressing and then releasing the back door switch after a closing operation was suspended, starts an opening operation.
When the power back door ECU detects a user operation, it sounds the power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the back door lock motor in order to release the latch and then actuates the power back door motor to open the back door. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Except models with manual transaxle *4: Pulse unit |
|||
| (a) | Back Door Opener Switch | Turned On | User operation is detected. |
| Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is unlocked and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. While vehicle speed is 3 km/h (2 mph) or less, shift lever is in P*3, brake pedal is depressed or parking brake is applied. (When power source mode is on (IG).) E. User operation is detected. When conditions A, B, C, D and E listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| (b) | Back Door Lock Motor | Changes from Off to Release | Approximately 0.8 seconds after user operation is detected, the release rotation relay turns on and a release operation starts. |
| (c) | Power Back Door Motor | Changes from Off to Opener | F. Courtesy switch is detected to be on. G. Courtesy switch and latch switch are detected to be on. H. Condition F or G listed above is not detected for approximately 1 second or more after the back door lock motor starts a release operation. When any one of the 3 conditions listed above is met while the back door lock motor is performing a release operation, the opener relay turns on and an opener operation starts. |
| (d) | Back Door Lock Motor | Changes from Release to Off | When the latch switch is detected to be on, the release rotation relay turns off and the release operation stops. |
| (e) | Back Door Lock Motor | Changes from Off to Engage | I. After the latch switch is detected to be on, the Hall ICs of the power back door motor detect a movement of 20 edges*4 in the opening direction. J. Approximately 3 seconds or more have elapsed since the back door lock motor was detected to be off. When condition I or J listed above is met, the engagement rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (f) | Back Door Lock Motor | Changes from Engage to Off | When the sector switch is detected to be on, the engagement rotation relay turns off and the reverse rotation operation stops. |
| (g) | Power Back Door Motor | Changes from Opener to Off | K. Hall ICs of the power back door motor detect a movement of 15 edges*4 in the closing direction from the fully open position. L. Power back door motor open output is detected continuously for approximately 30 seconds or more. When condition K or L listed above is met, the opener relay turns off and the opener operation stops. |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
Closer Function
Pressing and holding the power back door switch or power back door button for 0.8 seconds or more with the back door open (or after an opening operation was suspended) starts a closing operation.
When the power back door ECU detects a user operation, it sounds the wireless door lock buzzer and power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the power back door motor in order to close the back door and then actuates the back door lock motor to engage the latch. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Pulse unit |
|||
| (a) | Power Back Door Switch | Turned On (Pressed for Approximately 0.8 Seconds) | User operation is detected. |
| Power Back Door Button | |||
| (b) | Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 |
| Wireless Door Lock Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the wireless door lock buzzer sounds for approximately 0.8 seconds. | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is open and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. User operation is detected. When conditions A, B, C and D listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| Power Back Door Motor | Changes from Off to Closer | Approximately 0.8 seconds after user operation is detected, the closer relay turns on and a closer operation starts. | |
| (c) | Back Door Lock Motor | Changes from Off to Engage | When the latch switch is detected to be off, the engagement rotation relay turns on and an engagement operation starts. |
| (d) | Power Back Door Motor | Changes from Closer to Off | E. Courtesy switch is detected to be off. F. Power back door motor closer output is detected continuously for approximately 30 seconds or more. G. After the latch switch is detected to be off, the Hall ICs of the power back door motor detect a movement of 2 edges*3 in the closing direction. When any one of the 3 conditions listed above is met, the closer relay turns off and the closer operation stops. (If condition G listed above is met and the closer operation changes to off, output is reduced to secure the power needed to maintain the door position, and then after approximately 0.3 seconds, the output is stopped.) |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
| (e) | Back Door Lock Motor | Changes from Engage to Off | When the latch switch, courtesy switch and pawl switch are detected to be off, the engagement rotation relay turns off and the engagement operation stops. |
| (f) | Back Door Lock Motor | Changes from Off to Release | Approximately 0.1 seconds after the back door lock motor is detected to be off, the release rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (g) | Back Door Lock Motor | Changes from Release to Off | When the sector switch is detected to be on, the release rotation relay turns off and the reverse rotation operation stops. |
Pressing and then releasing the back door switch with the back door open (or after an opening operation was suspended) starts a closing operation.
When the power back door ECU detects a user operation, it sounds the power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the power back door motor in order to close the back door and then actuates the back door lock motor to engage the latch. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Pulse unit |
|||
| (a) | Back Door Switch | Turned On | User operation is detected. |
| Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is open and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. User operation is detected. When conditions A, B, C and D listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| (b) | Power Back Door Motor | Changes from Off to Closer | Approximately 0.8 seconds after user operation is detected, the closer relay turns on and a closer operation starts. |
| (c) | Back Door Lock Motor | Changes from Off to Engage | When the latch switch is detected to be off, the engagement rotation relay turns on and an engagement operation starts. |
| (d) | Power Back Door Motor | Changes from Closer to Off | E. Courtesy switch is detected to be off. F. Power back door motor closer output is detected continuously for approximately 30 seconds or more. G. After the latch switch is detected to be off, the Hall ICs of the power back door motor detect a movement of 2 edges*3 in the closing direction. When any one of the 3 conditions listed above is met, the closer relay turns off and the closer operation stops. (If condition G listed above is met and the closer operation changes to off, output is reduced to secure the power needed to maintain the door position, and then after approximately 0.3 seconds, the output is stopped.) |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
| (e) | Back Door Lock Motor | Changes from Engage to Off | When the latch switch, courtesy switch and pawl switch are detected to be off, the engagement rotation relay turns off and the engagement operation stops. |
| (f) | Back Door Lock Motor | Changes from Off to Release | Approximately 0.1 seconds after the back door lock motor is detected to be off, the release rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (g) | Back Door Lock Motor | Changes from Release to Off | When the sector switch is detected to be on, the release rotation relay turns off and the reverse rotation operation stops. |
Hands Free Power Back Door Function (Models with Hands Free Power Back Door)
Performing a touchless kick actuation operation with the back door closed (or after a closing operation was suspended) starts an opening operation.
When the power back door ECU detects a user operation, it sounds the power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the back door lock motor in order to release the latch and then actuates the power back door motor to open the back door. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Except models with manual transaxle *4: Pulse unit |
|||
| (a) | Kick Door Control Sensor | Turned On | User operation is detected. |
| Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is unlocked and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. While vehicle speed is 3 km/h (2 mph) or less, shift lever is in P*3, brake pedal is depressed or parking brake is applied. (When power source mode is on (IG).) E. User operation is detected. When conditions A, B, C, D and E listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| (b) | Back Door Lock Motor | Changes from Off to Release | Approximately 0.8 seconds after user operation is detected, the release rotation relay turns on and a release operation starts. |
| (c) | Power Back Door Motor | Changes from Off to Opener | F. Courtesy switch is detected to be on. G. Courtesy switch and latch switch are detected to be on. H. Condition F or G listed above is not detected for approximately 1 second or more after the back door lock motor starts a release operation. When any one of the 3 conditions listed above is met while the back door lock motor is performing a release operation, the opener relay turns on and an opener operation starts. |
| (d) | Back Door Lock Motor | Changes from Release to Off | When the latch switch is detected to be on, the release rotation relay turns off and the release operation stops. |
| (e) | Back Door Lock Motor | Changes from Off to Engage | I. After the latch switch is detected to be on, the Hall ICs of the power back door motor detect a movement of 20 edges*4 in the opening direction. J. Approximately 3 seconds or more have elapsed since the back door lock motor was detected to be off. When condition I or J listed above is met, the engagement rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (f) | Back Door Lock Motor | Changes from Engage to Off | When the sector switch is detected to be on, the engagement rotation relay turns off and the reverse rotation operation stops. |
| (g) | Power Back Door Motor | Changes from Opener to Off | K. Hall ICs of the power back door motor detect a movement of 15 edges*4 in the closing direction from the fully open position. L. Power back door motor open output is detected continuously for approximately 30 seconds or more. When condition K or L listed above is met, the opener relay turns off and the opener operation stops. |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
Performing a touchless kick actuation operation with the back door open (or after an opening operation was suspended) starts a closing operation.
When the power back door ECU detects a user operation, it sounds the power back door warning buzzer for 0.8 seconds, flashes the hazard lights 2 times*1, actuates the power back door motor in order to close the back door and then actuates the back door lock motor to engage the latch. Also, the power back door warning buzzer sounds intermittently while the power back door motor is operating.*2
*1: Models with power back door answer back hazard warning light function
*2: If the setting of the back door operating buzzer function is turned ON by the customization.
| [T] | Component | Operation | Outline |
|---|---|---|---|
|
*1: If the setting of the back door operating buzzer function is turned ON by the customization. *2: Models with power back door answer back hazard warning light function *3: Pulse unit |
|||
| (a) | Kick Door Control Sensor | Turned On | User operation is detected. |
| Power Back Door Warning Buzzer | Changes from Off to On | Approximately 0.8 seconds after user operation is detected, the power back door warning buzzer sounds for approximately 0.8 seconds. While the power back door motor is operating, the power back door warning buzzer sounds intermittently.*1 | |
| Hazard Lights*2 | Changes from Off to On | A. Power back door main switch is on. B. Power back door is open and not operating. C. Auxiliary battery voltage is 10.5 V or more. D. User operation is detected. When conditions A, B, C and D listed above are met, a flash request signal is sent to the combination meter. The combination meter flashes the hazard lights 2 times. |
|
| (b) | Power Back Door Motor | Changes from Off to Closer | Approximately 0.8 seconds after user operation is detected, the closer relay turns on and a closer operation starts. |
| (c) | Back Door Lock Motor | Changes from Off to Engage | When the latch switch is detected to be off, the engagement rotation relay turns on and an engagement operation starts. |
| (d) | Power Back Door Motor | Changes from Closer to Off | E. Courtesy switch is detected to be off. F. Power back door motor closer output is detected continuously for approximately 30 seconds or more. G. After the latch switch is detected to be off, the Hall ICs of the power back door motor detect a movement of 2 edges*3 in the closing direction. When any one of the 3 conditions listed above is met, the closer relay turns off and the closer operation stops. (If condition G listed above is met and the closer operation changes to off, output is reduced to secure the power needed to maintain the door position, and then after approximately 0.3 seconds, the output is stopped.) |
| Power Back Door Warning Buzzer*1 | Changes from On to Off | When the power back door motor is detected to be off, the power back door warning buzzer stops sounding. | |
| (e) | Back Door Lock Motor | Changes from Engage to Off | When the latch switch, courtesy switch and pawl switch are detected to be off, the engagement rotation relay turns off and the engagement operation stops. |
| (f) | Back Door Lock Motor | Changes from Off to Release | Approximately 0.1 seconds after the back door lock motor is detected to be off, the release rotation relay turns on and a reverse rotation operation starts in order to return the sector gear and back door lock motor to the initial position. |
| (g) | Back Door Lock Motor | Changes from Release to Off | When the sector switch is detected to be on, the release rotation relay turns off and the reverse rotation operation stops. |
FAIL-SAFE
When the power back door ECU detects a malfunction in parts such as a motor or sensor, the system enters fail-safe mode.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The Diagnostic Trouble Codes (DTCs) of malfunctions can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.