Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
NM3620E _59 Vehicle Exterior _077398 WINDOW / GLASS _0376458 POWER WINDOW CONTROL SYSTEM CO CONTROL F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  CONTROL  POWER WINDOW CONTROL  


SYSTEM CONTROL


a.

The power window control system has the following functions:

Function Outline

*1: HV models

*2: Gasoline models

*3: Although this function is disabled by default, the function can be set via the customization function.

*4: Except destination package for Korea

*5: Models with multimedia system or navigation system

Power Up-and-down This function causes the window to open or close while the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is being pulled halfway up or pushed halfway down. The window stops as soon as the switch is released.
One-touch Auto Up-and-down The one-touch auto up-and-down function enables the window to be fully opened or closed at a touch of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly.
Jam Protection The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during power up operation or one-touch auto up operation.
Catch Protection The catch protection function automatically stops the power window if a foreign object gets caught in the window during power down operation or one-touch auto down operation.
Soft Stop During an up or down operation of the power window, the power window ECU stops the current to the power window motor just before the door glass is fully closed or opened.
Remote Control The multiplex network master switch assembly can control the up-and-down operation of the front passenger door window and the rear door windows.
Window Lock
·

Disables operation of the 3 passenger windows using each power window regulator switch assembly when the window lock switch is on.

·

Even when the window lock switch is on, the 3 passenger windows can be operated using the multiplex network master switch assembly.


Key Off Operation
·

Makes it possible to operate the power windows for approximately 45 seconds after the power switch*1 or ignition switch*2 is turned off, if either front door is not opened.

·

If the window lock switch is off, the windows can be operated using the multiplex network master switch assembly or any of the power window regulator switch assemblies. If the window lock switch is on, only the multiplex network master switch assembly can be used to operate the windows.


Key-linked Up-and-down*3 When the driver door is locked, and the driver door key cylinder is turned and maintained in the lock direction for 1.5 seconds or more, the main body ECU activates the power window motors to raise all door windows while the key cylinder is turned. Similarly, when the driver door is unlocked, turning and maintaining the driver door key cylinder in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered.
Transmitter-linked Up-and-down*3, *4 When the lock button is pressed and held for longer than 3 seconds, the main body ECU activates the power window motors in accordance with the signal to raise all of the door windows. Similarly, when the unlock button is pressed and held for longer than 3 seconds, the main body ECU activates the power window motors in accordance with the signal to lower all of the door windows.
Power Window Glass Open Warning When the power switch is turned from on (IG) to off*1 or ignition switch is turned from ON to off*2 and the driver door is opened with the power window glass open, a warning message appears on the multi-information display.
Suggestion Function*4 When the wipers are operating with the door glass not fully closed (except during mist or washer operations), a message is displayed on the multi-information display and the windows can be closed all at once.
Customization The on or off setting of some functions can be performed using the Global TechStream (GTS) or radio and display receiver assembly*5. For details, refer to the Repair Manual.

HINT:

The ECU built into each power window motor stores the initial position of its door window glass. The initial position is not cleared even if the terminals, fuses or the power window motor connector are disconnected. However, after removing or reinstalling window components, or replacing the power window regulator switch assembly or power window regulator motor assembly, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.



b.

Jam Protection Function

i.

A jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window glass during power up operation and one-touch auto up operation.

HINT:

After the jam protection function has operated when a power up operation or one-touch auto up operation was performed, the jam protection function will not operate if the power up operation is performed again within approximately 4 seconds.



ii.

The operation of the jam protection function is described below:

Operation Function
During each door one-touch auto up operation and remote control power up/one-touch auto up operation Down operation of approximately 125 mm (4.9 in.) or 2.5 seconds
During each door power up operation Down operation of approximately 45 mm (1.8 in.) or 2.5 seconds


iii.

The power window ECU determines if a foreign object gets jammed according to changes in the output signal from the pulse sensor (Hall IC). Both of the following 2 judgment methods are used:

Judgment Method (Overload Detection)
Y146728E01
1.177,0.292 3.323,0.49 2.146,0.198 10 false Pulse Signal 1 1.177,0.938 3.323,1.135 2.146,0.198 10 false Pulse Signal 2 4.833,1.313 6.01,1.615 1.177,0.302 10 false Judged Jammed

Judgment Method (Rotation Speed Comparison)
Y146729E01
2.552,0.698 2.552,0.354 2.552,0.354 2.781,0.354 false 4.229,1.573 4.229,1.781 4.229,1.781 4.604,1.781 false 0.458,0.948 1.802,1.427 1.344,0.479 10 false Power Window Motor Rotation Speed 4.469,1.063 5.813,1.542 1.344,0.479 10 false Threshold Value 2.844,0.271 4.188,0.75 1.344,0.479 10 false Jamming Start 4.656,1.698 6,2.177 1.344,0.479 10 false Judged Jammed 2.76,2.25 4.333,2.604 1.573,0.354 10 false Number of Pulse Edges



c.

Catch Protection Function

i.

A catch protection function automatically stops the power window if a foreign object gets caught in the door window during power down operation and one-touch auto down operation.

HINT:

After the catch protection function has operated when a power down operation or one-touch auto down operation was performed, the catch protection function will not operate if the power down operation is performed again within approximately 4 seconds.



ii.

The power window ECU determines if a foreign object gets caught according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:

Judgment Method (Rotation Speed Comparison)
Y146730E01
2.563,0.688 2.563,0.375 2.563,0.375 2.781,0.375 false 4.698,1.854 4.24,1.854 4.24,1.854 4.24,1.583 false 0.5,0.927 1.833,1.417 1.333,0.49 10 false Power Window Motor Rotation Speed 2.844,0.292 4.177,0.781 1.333,0.49 10 false Catching Start 4.479,1.063 5.813,1.552 1.333,0.49 10 false Threshold Value 4.75,1.76 6.083,2.25 1.333,0.49 10 false Judged Caught 2.708,2.25 4.24,2.594 1.531,0.344 10 false Number of Pulse Edges



d.

Soft Stop Function

i.

During an up operation of the power window, the soft stop function stops the current to the power window motor just before the door glass is fully closed. This reduces the load on the door glass outer weatherstrip.


ii.

Just before the door glass is fully closed, the power window ECU determines if the door glass stop position is detected according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:

Judgment Method (Rotation Speed Comparison)
Y146731E01
2.552,0.698 2.552,0.385 2.552,0.385 2.781,0.385 false 4.594,1.833 4.24,1.833 4.24,1.833 4.24,1.583 false 0.49,0.969 1.833,1.427 1.344,0.458 10 false Power Window Motor Rotation Speed 2.833,0.292 4.448,0.667 1.615,0.375 10 false Change of Rotation Speed 4.469,1.063 5.656,1.438 1.188,0.375 10 false Threshold Value 4.646,1.74 6.26,2.115 1.615,0.375 10 false Judged Soft Stop 2.677,2.26 4.292,2.635 1.615,0.375 10 false Number of Pulse Edges


iii.

During a down operation of the power window, the power window ECU detects the rotation quantity of the power window motor according to output signals from the pulse sensor (Hall IC), and when the power window reaches the fully open stop position, the power window ECU stops the supply of power to the power window motor.



e.

Suggestion Function (Except Destination Package for Korea)

i.

Suggestion to close the power windows

1.

When both of the following conditions are met, a suggestion message "Close Open Windows?" will be displayed on the multi-information display for 6 seconds.

-

Any of the power windows is open.

-

The windshield wipers are operated.*

*: Excludes wiper operations for windshield washer operation or MIST function.



2.

When "Yes" is selected using the meter control switches, all open power windows will close.





FAIL-SAFE


a.

If a Hall IC in the power window motor malfunctions, some power window functions will be prohibited in fail-safe mode:

i.

Each power window only operates when the corresponding power window regulator switch is fully pushed down or pulled up and held in that position.


ii.

When any power window ECU detects an abnormality in a Hall IC, which detects the position, speed and direction of the window, it switches to fail-safe mode.




DIAGNOSIS


a.

If a power window ECU detects a malfunction in the power window control system, a Diagnostic Trouble Code (DTC) is stored in memory.

i.

The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.