Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2018.10–2019.02
NM3620E _51 Engine / Hybrid System _076456 CRUISE CONTROL _0377064 CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  CRUISE CONTROL SYSTEM  CONTROL  CRUISE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the cruise control system have the following functions:

HV Models
Component Function

*: Models with shift paddle switch

Steering Pad Switch Assembly Cruise Control Switch Turns the cruise control system on and off.
CANCEL Switch A cancel signal is output to the hybrid vehicle control ECU when this switch is operated.
+RES Switch The accelerate function and resuming of a preset speed can be performed by operating this switch. A signal is output to the hybrid vehicle control ECU when this switch is operated.
-SET Switch The decelerate function and vehicle speed setting signals are output to the hybrid vehicle control ECU when this switch is operated.
Stop Light Switch Assembly Detects the brake pedal being depressed and transmits its signal to the hybrid vehicle control ECU.
Shift Lever Position Sensor Detects the shift lever position and transmits signals to the hybrid vehicle control ECU.
Shift Lock Control Unit Assembly Transmission Control Switch
·

Detects the shift lever position and transmits signals to the hybrid vehicle control ECU.

·

Informs the hybrid vehicle control ECU of driver upshift or downshift operations while the shift lever is in S.


Shift Paddle Switch (Transmission Shift Switch Assembly)* While the vehicle is being driven in D mode, this switch outputs a signal to the hybrid vehicle control ECU when the switch is pulled to "+" or "-".
VSC OFF Switch Detects the VSC OFF or TRC OFF signal and outputs it to the skid control ECU.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the hybrid vehicle control ECU.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Inverter with Converter Assembly MG ECU Controls the motive force of hybrid vehicle transaxle assembly in accordance with signals from the hybrid vehicle control ECU.
Hybrid Vehicle Transaxle Assembly Generates motive force for the front wheels.
Combination Meter Assembly Cruise Control Indicator
·

Based on a cruise control indicator operation signal sent by the hybrid vehicle control ECU, the combination meter assembly illuminates the cruise control indicator when the cruise control system has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator operation signal sent by the hybrid vehicle control ECU, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display Displays a warning message to alert the driver in accordance with a signal received from the hybrid vehicle control ECU.
Buzzer If the hybrid vehicle control ECU detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.
Hybrid Vehicle Control ECU
·

Controls all functions of the cruise control system in accordance with the signals from switches, sensors and ECUs.

·

If the hybrid vehicle control ECU detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC).


ECM Actuates the throttle control motor in accordance with the signals from the hybrid vehicle control ECU.
Brake Booster with Master Cylinder Assembly Skid Control ECU
·

Transmits the wheel speed signal to the hybrid vehicle control ECU.

·

Transmits the VSC operation signal to the hybrid vehicle control ECU.


Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.

Gasoline Models
Component Function

*1: Except models with manual transaxle

*2: Models with automatic transaxle

*3: Models with CVT

*4: Models with manual transaxle

*5: Models with shift paddle switch

*6: 4WD/AWD models

*7: Models with downhill assist control

Steering Pad Switch Assembly Cruise Control Switch Turns the cruise control system on and off.
CANCEL Switch A cancel signal is output to the ECM when this switch is operated.
+RES Switch The accelerate function and resuming of a preset speed can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
-SET Switch The decelerate function and vehicle speed setting signals are output to the ECM when this switch is operated.
Stop Light Switch Assembly Detects the brake pedal being depressed and transmits its signal to the ECM.
Park/Neutral Position Switch Assembly*1
·

Detects the shift lever position and transmits signals to the ECM.*2

·

Detects the shift lever position and transmits signals to the transmission control ECU.*3


Neutral Position Switch*4 Detects the neutral position and transmits signals to the ECM.
Transmission Floor Shift Assembly Transmission Control Switch*1
·

Detects the shift lever position and transmits signals to the ECM.*2

·

Detects the shift lever position and transmits signals to the transmission control ECU.*3

·

Informs the ECM of driver upshift or downshift operations while the shift lever is in S.*2

·

Informs the transmission control ECU of driver upshift or downshift operations while the shift lever is in M.*3


Shift Paddle Switch (Transmission Shift Switch Assembly)*5
·

While the vehicle is being driven in D or S mode, this switch outputs a signal to the ECM when the switch is pulled to "+" or "-".*2

·

While the vehicle is being driven in D or M mode, this switch outputs a signal to the transmission control ECU when the switch is pulled to "+" or "-".*3


VSC OFF Switch Detects the VSC OFF or TRC OFF signal and outputs it to the skid control ECU.
Integration Control and Panel Assembly Multi-terrain Select Switch*6 Detects the multi-terrain select mode and transmits signals to the 4WD ECU assembly.
Downhill Assist Control Switch*7 Detects the switch condition and transmits signals to the skid control ECU.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the ECM.
Clutch Pedal Stroke Sensor Assembly*4 Detects the clutch pedal depression angle and transmits it to the ECM.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Combination Meter Assembly Cruise Control Indicator
·

Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator when the cruise control system has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display Displays a warning message to alert the driver in accordance with a signal received from the ECM.
Buzzer If the ECM detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.
ECM
·

Controls all functions of the cruise control system in accordance with the signals from switches, sensors and ECUs.

·

If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC).


Transmission Control ECU*3 Transmits the shift lever position signal to the ECM.
4WD ECU Assembly*6 Transmits the multi-terrain select mode to the ECM.
Brake Actuator Assembly Skid Control ECU
·

Transmits the wheel speed signal to the ECM.

·

Transmits the VSC operation signal to the ECM.


Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.



SYSTEM CONTROL


a.

The cruise control system has the following control functions:

HV Models
Function Outline
Constant Speed Control The hybrid vehicle control ECU compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, the hybrid vehicle control ECU calculates the optimal motive forces, and accelerates by adjusting the respective motive forces.
Set Control When this system fulfills the following conditions, and the -SET switch on the steering pad switch assembly is pressed and released, the hybrid vehicle control ECU stores the vehicle speed and maintains the vehicle constantly at that speed.
·

The cruise control system has been turned on using the cruise control switch on the steering pad switch assembly

·

The vehicle is being driven at a speed of approximately 30 km/h (20mph) or more


Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is operating, speed control by the cruise control system will be canceled automatically. However, the set speed is kept in memory.
Coast Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will decelerate

·

The set vehicle speed changes to the speed at which the -SET switch is released


Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed


Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·

The vehicle accelerates constantly

·

The set vehicle speed changes to the speed at which the +RES switch is released


Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change


Resume Control When the vehicle speed is above the low speed limit, the cruise control system resumes operation (when the +RES switch on the steering pad switch assembly is pushed) to reach the vehicle speed that was set at the time the driver canceled cruise control. Even if the vehicle speed dropped below the low speed limit, the set speed can be resumed after the vehicle speed increases above the low speed limit. Also, if the vehicle speed memory is deleted, the return control cannot be performed.
Manual Cancel Control If any of the following signals are sent to the hybrid vehicle control ECU, speed control by the cruise control system is canceled accordingly.
·

Stop light switch assembly on signal (the brake pedal is depressed)

·

Shift lever is moved from D or S to any other position

·

When 1st, 2nd or 3rd range is selected in S position by shift lever

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (transmission shift switch assembly)

·

Cruise control switch off signal sent to the hybrid vehicle control ECU

·

CANCEL switch on signal (CANCEL switch on the steering pad switch assembly is pushed)


Automatic Cancel Control If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Stop light switch assembly open or short circuit


Furthermore, the cruise control indicator turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly.
If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Malfunction in the hybrid system


Furthermore, speed control by the cruise control system is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly.
If any of the following conditions occur during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Stop light switch assembly input signal is abnormality

·

Cancel circuit malfunction

·

Brake control system malfunction

·

Communication malfunction between the skid control ECU and hybrid vehicle control ECU


Furthermore, the cruise control indicator turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the power switch is turned off.
If the following condition occurs while the cruise control system is controlling the vehicle speed, the speed that is stored in memory is cleared and speed control by the cruise control system is canceled.
·

Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set


If the following condition occurs while the cruise control system is controlling the vehicle speed, speed control by the cruise control system is canceled.
·

Vehicle speed decreases below the low speed limit [approximately 30 km/h (20 mph)]


Other Cancel Conditions
·

Power switch off (the set speed is not stored in the memory)

·

VSC is activated (the set speed remains in the memory)

·

TRC is activated for a period of time (the set speed remains in the memory)

·

VSC or TRC system is turned off (the set speed remains in the memory)



Gasoline Models
Function Outline

*1: Models with automatic transaxle

*2: Models with CVT

*3: Models with shift paddle switch

*4: Models with manual transaxle

*5: Models with downhill assist control

*6: 4WD/AWD models

Constant Speed Control The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle valve opening angle.
Set Control When this system fulfills the following conditions, and the -SET switch on the steering pad switch assembly is pressed and released, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed.
·

The cruise control system has been turned on using the cruise control switch on the steering pad switch assembly

·

The vehicle is being driven at a speed of approximately 30 km/h (20mph) or more


Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is operating, speed control by the cruise control system will be canceled automatically. However, the set speed is kept in memory.
Coast Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will decelerate

·

The set vehicle speed changes to the speed at which the -SET switch is released


Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed


Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·

The vehicle accelerates constantly

·

The set vehicle speed changes to the speed at which the +RES switch is released


Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change


Resume Control When the vehicle speed is above the low speed limit, the cruise control system resumes operation (when the +RES switch on the steering pad switch assembly is pushed) to reach the vehicle speed that was set at the time the driver canceled cruise control. Even if the vehicle speed dropped below the low speed limit, the set speed can be resumed after the vehicle speed increases above the low speed limit. Also, if the vehicle speed memory is deleted, the return control cannot be performed.
Shift Down Control*1 When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift-down control, when the end of uphill travel is determined based on the throttle valve angle, the transmission will shift up after a certain period of time. When the transmission shifts down during accelerator control or resume control, the transmission will shift up after accelerator control or resume control ends.
Manual Cancel Control If any of the following signals are sent to the ECM, speed control by the cruise control system is canceled accordingly.
·

Stop light switch assembly on signal (the brake pedal is depressed)

·

Shift lever is moved from D or S to any other position*1

·

Shift lever is moved from D to any other position*2

·

When 1st, 2nd or 3rd range is selected in S position by shift lever*1

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (transmission shift switch assembly)*3

·

Depress the clutch pedal*4

·

Cruise control switch off signal sent to the ECM

·

CANCEL switch on signal (CANCEL switch on the steering pad switch assembly is pushed)


Automatic Cancel Control If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Stop light switch assembly open or short circuit


Furthermore, the cruise control indicator turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly.
If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Malfunction in the engine control system


Furthermore, speed control by the cruise control system is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly.
If any of the following conditions occur during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·

Stop light switch assembly input signal is abnormality

·

Cancel circuit malfunction

·

Brake control system malfunction

·

Communication malfunction between the skid control ECU and ECM


Furthermore, the cruise control indicator turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the ignition switch is turned off.
If the following condition occurs while the cruise control system is controlling the vehicle speed, the speed that is stored in memory is cleared and speed control by the cruise control system is canceled.
·

Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set


If the following condition occurs while the cruise control system is controlling the vehicle speed, speed control by the cruise control system is canceled.
·

Vehicle speed decreases below the low speed limit [approximately 30 km/h (20 mph)]


Other Cancel Conditions
·

Ignition switch off (the set speed is not stored in the memory)

·

VSC is activated (the set speed remains in the memory)

·

TRC is activated for a period of time (the set speed remains in the memory)

·

VSC or TRC system is turned off (the set speed remains in the memory)

·

Downhill assist control switch is turned on (the set speed remains in the memory)*5

·

Off-road mode is selected by the multi-terrain select switch (the set speed remains in the memory)*6





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.