Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2018.10–2019.02
NM3620E _51 Engine / Hybrid System _076456 CRUISE CONTROL _0377065 DYNAMIC RADAR CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  CONTROL  CRUISE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the dynamic radar cruise control system have the following functions:

HV Models
Component Function

*1: Models with RSA system

*2: Models with shift paddle switch

Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Forward Recognition Camera
·

Detects lane markers and objects on the road ahead using the image captured by the camera sensor.

·

While the system is in vehicle-to-vehicle distance control mode, the forward recognition camera detects the vehicle ahead based on signals from the millimeter wave radar sensor and forward recognition camera. Then, the forward recognition camera calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the hybrid vehicle control ECU.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.

·

If the detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Steering Pad Switch Assembly Cruise Control Switch
·

Turns the cruise control system on and off.

·

Vehicle-to-vehicle distance control mode becomes be activated immediately after the switch is turned on. The mode shifts to constant speed control mode by pressing and holding the switch more than 1.5 seconds.


CANCEL Switch A cancel signal is output to the hybrid vehicle control ECU when this switch is operated.
+RES Switch
·

The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the hybrid vehicle control ECU when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the hybrid vehicle control ECU.*1


-SET Switch
·

The deceleration function and vehicle speed setting resume signals are output to the hybrid vehicle control ECU when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the hybrid vehicle control ECU.*1


Vehicle-to-vehicle Distance Control Switch While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in 3 levels: long, middle and short.
Stop Light Switch Assembly Detects brake pedal depression and transmits its signal to the hybrid vehicle control ECU.
Shift Lever Position Sensor Detects the shift lever position and transmits signals to the hybrid vehicle control ECU.
Shift Lock Control Unit Assembly Transmission Control Switch
·

Detects the shift lever position and transmits signals to the hybrid vehicle control ECU.

·

Informs the hybrid vehicle control ECU of driver upshift or downshift operations while the shift lever is in S.


Shift Paddle Switch (Transmission Shift Switch Assembly)*2 While the vehicle is being driven in D mode, this switch outputs a signal to the hybrid vehicle control ECU when the switch is pulled to "+" or "-".
VSC OFF Switch Detects the VSC OFF or TRC OFF signal and outputs it to the skid control ECU.
Electric Parking Brake Switch Assembly Sends a parking brake application signal to the parking brake ECU assembly.
Turn Signal Switch Sends a turn signal command to the steering sensor.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the hybrid vehicle control ECU.
Steering Sensor
·

Detects the angle and direction of steering and sends signals to the hybrid vehicle control ECU.

·

Sends a turn signal command to the hybrid vehicle control ECU.


Airbag ECU (Airbag Sensor Assembly) Yawrate Sensor Detects the yaw rate of the vehicle and sends signals to the hybrid vehicle control ECU.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Inverter with Converter Assembly MG ECU Controls the motive force of hybrid vehicle transaxle assembly in accordance with signals from the hybrid vehicle control ECU.
Hybrid Vehicle Transaxle Assembly Generates motive force for the front wheels.
Combination Meter Assembly Cruise Control Indicator (Constant Speed Control Mode)
·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the hybrid vehicle control ECU, the combination meter assembly illuminates the cruise control indicator (constant speed control mode) when the dynamic radar cruise control system in constant speed control mode has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the hybrid vehicle control ECU, the combination meter assembly turns off the cruise control indicator light if a malfunction occurs in the dynamic radar cruise control system.


Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode)
·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the hybrid vehicle control ECU, the combination meter assembly illuminates the cruise control indicator (vehicle-to-vehicle distance control mode) when the dynamic radar cruise control system in vehicle-to-vehicle distance control mode has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the hybrid vehicle control ECU, the combination meter assembly turns off the cruise control indicator (vehicle-to-vehicle distance control mode) if a malfunction occurs in the dynamic radar cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display
·

Displays a warning message to alert the driver in accordance with a signal provided by the hybrid vehicle control ECU.

·

During dynamic radar cruise control operation, the multi-information display receives signals from the hybrid vehicle control ECU in order to display the system conditions.


Buzzer
·

Sounds a buzzer when it receives a signal from the hybrid vehicle control ECU to alert the driver that the distance between vehicles is short.

·

If the hybrid vehicle control ECU detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.


Hybrid Vehicle Control ECU
·

Controls the dynamic radar cruise control system in accordance with signals from switches, sensors.

·

If the hybrid vehicle control ECU detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


ECM Actuates the throttle control motor in accordance with the signals from the hybrid vehicle control ECU.
Brake Booster with Master Cylinder Assembly Skid Control ECU
·

While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU operates the brake actuator in accordance with the brake request signal received from the hybrid vehicle control ECU.

·

Applies the brakes in accordance with signals from the hybrid vehicle control ECU.


Parking Brake ECU Assembly Sends an electric parking brake system condition signal to the hybrid vehicle control ECU.
Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.

Gasoline Models
Component Function

*1: Models with RSA system

*2: Except models with manual transaxle

*3: Models with automatic transaxle

*4: Models with CVT

*5: Models with manual transaxle

*6: Models with shift paddle switch

*7: 4WD/AWD models

*8: Models with downhill assist control

*9: Models with stop and start system

Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Forward Recognition Camera
·

Detects lane markers and objects on the road ahead using the image captured by the camera sensor.

·

While the system is in vehicle-to-vehicle distance control mode, the forward recognition camera detects the vehicle ahead based on signals from the millimeter wave radar sensor assembly and forward recognition camera. Then, the forward recognition camera calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the ECM.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.

·

If the detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Steering Pad Switch Assembly Cruise Control Switch
·

Turns the cruise control system on and off.

·

Vehicle-to-vehicle distance control mode becomes be activated immediately after the switch is turned on. The mode shifts to constant speed control mode by pressing and holding the switch more than 1.5 seconds.


CANCEL Switch A cancel signal is output to the ECM when this switch is operated.
+RES Switch
·

The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the ECM when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.*1


-SET Switch
·

The deceleration function and vehicle speed setting resume signals are output to the ECM when this switch is operated.

·

The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.*1


Vehicle-to-vehicle Distance Control Switch While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in 3 levels: long, middle and short.
Stop Light Switch Assembly Detects brake pedal depression and transmits its signal to the ECM.
Park/Neutral Position Switch Assembly*2
·

Detects the shift lever position and transmits signals to the ECM.*3

·

Detects the shift lever position and transmits signals to the transmission control ECU.*4


Neutral Position Switch*5 Detects the neutral position and transmits signals to the ECM.
Transmission Floor Shift Assembly Transmission Control Switch*2
·

Detects the shift lever position and transmits signals to the ECM.*3

·

Detects the shift lever position and transmits signals to the transmission control ECU.*4

·

Informs the ECM of driver upshift or downshift operations while the shift lever is in S.*3

·

Informs the transmission control ECU of driver upshift or downshift operations while the shift lever is in M.*4


Shift Paddle Switch (Transmission Shift Switch Assembly)*6
·

While the vehicle is being driven in D or S mode, this switch outputs a signal to the ECM when the switch is pulled to "+" or "-".*3

·

While the vehicle is being driven in D or M mode, this switch outputs a signal to the transmission control ECU when the switch is pulled to "+" or "-".*4


VSC OFF Switch Detects the VSC OFF or TRC OFF signal and outputs it to the skid control ECU.
Electric Parking Brake Switch Assembly Sends a parking brake application signal to the skid control ECU.
Turn Signal Switch Sends a turn signal command to the steering sensor.
Integration Control and Panel Assembly Multi-terrain Select Switch*7 Detects the multi-terrain select mode and transmits signals to the 4WD ECU assembly.
Downhill Assist Control Switch*8 Detects the switch condition and transmits signals to the skid control ECU.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the ECM.
Clutch Pedal Stroke Sensor Assembly*5 Detects the clutch pedal depression angle and transmits it to the ECM.
Steering Sensor
·

Detects the angle and direction of steering and sends signals to the ECM.

·

Sends a turn signal command to the ECM.


Airbag ECU (Airbag Sensor Assembly) Yawrate Sensor Detects the yaw rate of the vehicle and sends signals to the ECM.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Combination Meter Assembly Cruise Control Indicator (Constant Speed Control Mode)
·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator (constant speed control mode) when the dynamic radar cruise control system in constant speed control mode has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator (constant speed control mode) operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator light if a malfunction occurs in the dynamic radar cruise control system.


Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode)
·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator (vehicle-to-vehicle distance control mode) when the dynamic radar cruise control system in vehicle-to-vehicle distance control mode has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator (vehicle-to-vehicle distance control mode) operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator (vehicle-to-vehicle distance control mode) if a malfunction occurs in the dynamic radar cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display
·

Displays a warning message to alert the driver in accordance with a signal provided by the ECM.

·

During dynamic radar cruise control operation, the multi-information display receives signals from the ECM in order to display the system conditions.


Buzzer
·

Sounds a buzzer when it receives a signal from the ECM to alert the driver that the distance between vehicles is short.

·

If the ECM detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.


ECM
·

Controls the dynamic radar cruise control system in accordance with signals from switches, sensors.

·

If the ECM detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Transmission Control ECU*4
·

Controls the CVT system.

·

Transmits the shift lever position signal to the ECM.


Brake Actuator Assembly Skid Control ECU
·

While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU operates the brake actuator in accordance with the brake request signal received from the ECM.

·

Applies the brakes in accordance with signals from the ECM.

·

Sends an electric parking brake system condition signal to the ECM.


4WD ECU Assembly*7 Transmits the multi-terrain select mode to the ECM.
Engine Stop and Start ECU Assembly*9 Transmits the neutral position switch signal to the ECM.
Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.



SYSTEM CONTROL


a.

System Control for HV Models

i.

The control of the dynamic radar cruise control system varies depending on the mode:

A: Constant Speed Control Mode

B: Vehicle-to-vehicle Distance Control Mode (Models without full-speed range following function)

C: Vehicle-to-vehicle Distance Control Mode (Models with full-speed range following function)

Function Outline Mode
A B C

○: Available

-: Not available

x: Not setting

*1: Models with RSA system

*2: Except models for Europe

*3: Models for Europe

*4: Models with shift paddle switch

Constant Speed Control The hybrid vehicle control ECU compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it accelerates the vehicle by adjusting the respective motive forces. ○ ○ ○
Deceleration Control Performs engine control, MG control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead is maintained at the set distance. - ○ ○
Follow-up Control After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance. The actual distance maintained for each distance level (long, medium and short) varies in accordance with the vehicle speed. - ○ ○
Acceleration Control Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. - ○ ○
Stop Control Detects if the vehicle ahead has stopped, performs motive force control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. - - ○
Stop Retention Control Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. - - ○
Start Control Detects that the vehicle ahead starts moving again, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch on the steering pad switch assembly or depress the accelerator pedal), and resumes follow-up control after the vehicle is started. - - ○
Turn signal-linked Control If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed. - ○ ○
Dynamic Radar Cruise Control with Road Sign Assist*1 This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit. - x ○
Set Control When the dynamic radar cruise control system has been turned on using the cruise control switch on the steering pad switch assembly, either of the relevant vehicle speed conditions shown below is met, and the -SET switch on the steering pad switch assembly is pressed, the hybrid vehicle control ECU stores the vehicle speed and maintains the vehicle constantly at that speed. ○ ○ ○
The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or more. ○ ○ ○
When the vehicle is traveling at a speed of approximately 30 km/h (20 mph) or less and a vehicle ahead is detected, the set vehicle speed is set to the low speed limit [approximately 30 km/h (20 mph)]. - - ○
Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. ○ ○ -
COAST Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle decelerates constantly.

·

The set vehicle speed changes to the speed at which the -SET switch is released.


○ - -
·

The set vehicle speed decreases in increments of 5 km/h or 5 mph. [Example: 103 →100 → 95 → 90 → 85 km/h (mph)]

·

The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released.


- ○ ○
Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was being driven at the time the -SET switch was operated.


○ - -
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is pushed.*2

·

The vehicle will decelerate in increments of approximately 5 km/h or 5 mph for each time the -SET switch is pushed.*3


- ○ ○
Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will accelerate constantly.

·

The set vehicle speed changes to the speed at which the +RES switch is released.


○ - -
·

The set vehicle speed increases in increments of 5 km/h or 5 mph. [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)]

·

The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set vehicle speed will change during follow-up control.


- ○ ○
Resume Control If the vehicle speed is above the low speed limit, the +RES switch on the steering pad switch assembly can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. ○ ○ ○
Even if the vehicle speed drops below the low speed limit, resumption can be performed when the vehicle speed increases to above the low speed limit. However, resumption can be performed even if the vehicle speed is below the low speed limit when the vehicle is running in mode B and there is a vehicle ahead. - - ○
If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by pushing the +RES switch on the steering pad switch assembly. - ○ ○
After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the steering pad switch assembly is pushed to the +RES switch, follow-up control is resumed and the vehicle can be accelerated up to the set speed. - - ○
Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows: ○ ○ ○
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.


○ - -
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is pushed.*2

·

The vehicle will accelerate in increments of approximately 5 km/h or 5 mph for each time the +RES switch is pushed.*3


- ○ ○
Manual Cancel Control If any of the following signals are sent to the hybrid vehicle control ECU, the cruise control is canceled accordingly:
·

Stop light switch on signal. (The brake pedal is depressed)

·

Shift lever is moved from D or S to any other position.

·

CANCEL switch on signal. (CANCEL switch on the steering pad switch assembly is pushed)

·

When 1st, 2nd or 3rd range is selected in S position by shift lever.

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (transmission shift switch assembly).*4

·

Cruise control switch off signal. (Cruise control switch on the steering pad switch assembly is pushed)

·

Electric parking brake is applied. (Only during vehicle-to-vehicle distance control mode)


○ ○ ○
Automatic Cancel Control When an automatic cancel signal is sent to the hybrid vehicle control ECU, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. ○ ○ ○
Mode Switching Control The following operations switch modes:
·

Vehicle-to-vehicle distance control mode is activated immediately after the switch is turned on. The mode is changed to constant speed control mode by pressing and holding the switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off.


○ ○ ○
Other Cancel Conditions
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time while the cruise control.

·

TRC is off or VSC is off.

·

Power switch off.

·

Pre-collision system operates during cruise control driving.

·

Drive start control operates during cruise control driving. (Only during vehicle-to-vehicle distance control mode).

·

Parking support brake system operates during cruise control driving (Only during vehicle-to-vehicle distance control mode).

·

Electric parking brake system operates during cruise control driving. (Only during vehicle-to-vehicle distance control mode).


○ ○ ○
Diagnosis If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the hybrid vehicle control ECU cancels cruise control and memorizes information related to the malfunction. ○ ○ ○


ii.

Constant Speed Control Mode

·

The hybrid vehicle control ECU compares the set vehicle speed and the actual vehicle speed, and performs constant speed control in order to attain the set vehicle speed.



iii.

Vehicle-to-vehicle Distance Control Mode

·

In vehicle-to-vehicle distance control mode, the hybrid vehicle control ECU performs constant speed control function, deceleration control function, follow-up control function, acceleration control function, stop control function*, stop retention control function*, start control function* or turn signal-linked control function based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.

*: Models with full-speed range following function



1.

Constant Speed Control Function

(a)

The hybrid vehicle control ECU compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the throttle in order to attain the set vehicle speed. The forward recognition camera uses the millimeter wave radar sensor assembly signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the hybrid vehicle control ECU.

Y230944E01
1.792,0.354 3.635,0.667 1.844,0.313 10 false Forward Recognition Camera 4.885,0.333 6.76,0.802 1.875,0.469 10 false Millimeter Wave Radar Sensor Assembly 2.813,2.302 4.198,2.792 1.385,0.49 10 false Hybrid Vehicle Control ECU 5.115,1.448 6.427,1.698 1.313,0.25 10 false Acceleration Control 5.479,1.875 6.167,2.083 0.688,0.208 10 false MG ECU 5.406,2.167 6.438,2.354 1.031,0.188 10 false - MG2 Control 5.698,2.604 6.302,2.865 0.604,0.26 10 false ECM 5.354,3.177 6.792,3.406 1.438,0.229 10 false - Throttle Valve Control 0.75,2.656 1.792,2.99 1.042,0.333 10 false Own Vehicle 5.229,2.875 6.688,3.031 1.458,0.156 10 false Throttle Control Motor


2.

Deceleration Control Function

(a)

The forward recognition camera calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, forward recognition camera and transmits a deceleration request signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU performs engine, MG2 and brake control in order to cause the vehicle to decelerate.

(b)

This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.

Y230945E01
1.229,0.281 3.073,0.583 1.844,0.302 10 false Forward Recognition Camera 4.865,0.25 6.75,0.635 1.885,0.385 10 false Millimeter Wave Radar Sensor Assembly 2.938,2.01 4.323,2.406 1.385,0.396 10 false Hybrid Vehicle Control ECU 0.719,1.729 1.781,1.99 1.063,0.26 10 false Vehicle Ahead 0.792,3.75 1.854,4.01 1.063,0.26 10 false Own Vehicle 5.104,1.115 6.438,1.354 1.333,0.24 10 false Acceleration Control 5.49,1.542 6.229,1.719 0.74,0.177 10 false MG ECU 5.521,1.875 6.698,2.094 1.177,0.219 10 false - MG Control 5.75,2.26 6.26,2.479 0.51,0.219 10 false ECM 5.302,2.531 6.75,2.719 1.448,0.188 10 false Throttle Control Motor 5.26,3.417 6.719,3.667 1.458,0.25 10 false Deceleration Control 5.021,3.948 6.792,4.167 1.771,0.219 10 false Skid Control ECU Assembly 5.406,4.198 6.646,4.417 1.24,0.219 10 false - Brake Control 5.385,2.833 6.833,3.021 1.448,0.188 10 false - Throttle Valve Control

(c)

If the forward recognition camera determines that further deceleration is necessary, it transmits a brake request signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.

(d)

At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.

Y230946E01
1.26,0.24 3.125,0.677 1.865,0.438 10 false Forward Recognition Camera 4.906,0.25 6.771,0.635 1.865,0.385 10 false Millimeter Wave Radar Sensor Assembly 0.896,1.479 2,1.708 1.104,0.229 10 false Vehicle Ahead 0.792,2.938 1.896,3.167 1.104,0.229 10 false Own Vehicle 0.823,4.073 1.927,4.302 1.104,0.229 10 false Vehicle Behind 3.021,1.927 4.417,2.438 1.396,0.51 10 false Hybrid Vehicle Control ECU 5.24,1.073 6.927,1.323 1.688,0.25 10 false Acceleration Control 5.635,1.469 6.323,1.76 0.688,0.292 10 false MG ECU 5.5,1.771 6.906,1.969 1.406,0.198 10 false - MG2 Control 5.76,2.208 6.25,2.417 0.49,0.208 10 false ECM 5.354,2.813 6.885,3.135 1.531,0.323 10 false - Throttle Valve Control 5.229,3.385 6.792,3.635 1.563,0.25 10 false Deceleration Control 5.417,3.917 6.531,4.094 1.115,0.177 10 false Skid Control ECU 5.49,4.167 6.625,4.396 1.135,0.229 10 false - Brake Control 5.271,2.51 6.833,2.76 1.563,0.25 10 false Throttle Control Motor

(e)

If the vehicle is not decelerating adequately, the hybrid vehicle control ECU sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.

Y230947E01
0.76,1.698 1.823,2.031 1.063,0.333 10 false Vehicle Ahead 0.813,3.292 1.875,3.625 1.063,0.333 10 false Own Vehicle 0.771,4.313 1.833,4.646 1.063,0.333 10 false Vehicle Behind 1.729,0.229 3.677,0.469 1.948,0.24 10 false Forward Recognition Camera 4.802,0.208 6.698,0.656 1.896,0.448 10 false Millimeter Wave Radar Sensor Assembly 5.531,1.104 6.427,1.344 0.896,0.24 10 false Warning 5.552,1.49 6.448,1.729 0.896,0.24 10 false Buzzer 5.156,2.042 6.698,2.281 1.542,0.24 10 false Acceleration Control 5.604,2.5 6.333,2.708 0.729,0.208 10 false MG ECU 5.542,2.823 6.594,3.01 1.052,0.188 10 false - MG2 Control 5.74,3.219 6.25,3.49 0.51,0.271 10 false ECM 5.281,3.781 6.708,4 1.427,0.219 10 false - Throttle Valve Control 5.177,4.375 6.573,4.656 1.396,0.281 10 false Deceleration Control 5.26,4.833 6.427,5.115 1.167,0.281 10 false Skid Control ECU 5.354,5.177 6.396,5.406 1.042,0.229 10 false - Brake Control 2.885,2.969 4.271,3.427 1.385,0.458 10 false Hybrid Vehicle Control ECU 5.188,3.49 6.844,3.708 1.656,0.219 10 false Throttle Control Motor


3.

Follow-up Control Function

(a)

After performing deceleration control, the forward recognition camera transmits request signals to the hybrid vehicle control ECU so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving these signals, these ECUs control the motive force in order to perform follow-up control.

(b)

3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.

Y230948E01
0.917,3.344 2.01,3.896 1.094,0.552 10 false Vehicle-to-vehicle Distance 0.781,2.656 1.906,2.885 1.125,0.229 10 false Vehicle Ahead 0.76,4.177 1.74,4.417 0.979,0.24 10 false Own Vehicle 1.573,0.802 3.469,1.063 1.896,0.26 10 false Forward Recognition Camera 4.844,0.813 6.75,1.208 1.906,0.396 10 false Millimeter Wave Radar Sensor Assembly 4.74,1.625 6.74,2 2,0.375 10 false Steering Pad Switch Assembly 4.927,2.167 6.594,2.698 1.667,0.531 10 false Vehicle-to-vehicle Distance Control Switch 5.063,3.031 6.625,3.302 1.563,0.271 10 false Acceleration Control 5.75,3.469 6.448,3.719 0.698,0.25 10 false MG ECU 5.594,3.781 6.75,3.99 1.156,0.208 10 false - MG2 Control 5.906,4.208 6.396,4.438 0.49,0.229 10 false ECM 5.438,4.781 6.896,5 1.458,0.219 10 false - Throttle Valve Control 5.208,5.302 6.708,5.479 1.5,0.177 10 false Deceleration Control 5.281,5.74 6.781,5.917 1.5,0.177 10 false Skid Control ECU 5.344,6.104 6.844,6.281 1.5,0.177 10 false - Brake Control 2.865,3.906 4.271,4.448 1.406,0.542 10 false Hybrid Vehicle Control ECU 5.365,4.479 6.823,4.656 1.458,0.177 10 false Throttle Control Motor


4.

Acceleration Control Function

(a)

If the forward recognition camera detects (based on the millimeter wave radar sensor and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the hybrid vehicle control ECU in order to attain the set vehicle speed. Upon receiving this signal, the hybrid vehicle control ECU controls the motive force of the engine and MG2 in order to perform acceleration control.

Y230949E01
2.135,0.25 3.458,0.781 1.323,0.531 10 false Forward Recognition Camera 4.729,0.25 6.625,0.74 1.896,0.49 10 false Millimeter Wave Radar Sensor Assembly 5.115,1.375 6.531,1.615 1.417,0.24 10 false Acceleration Control 5.552,1.833 6.313,2.042 0.76,0.208 10 false MG ECU 5.396,2.146 6.5,2.417 1.104,0.271 10 false - MG2 Control 2.813,2.229 4.208,2.823 1.396,0.594 10 false Hybrid Vehicle Control ECU 5.667,2.552 6.177,2.844 0.51,0.292 10 false ECM 5.25,3.125 6.844,3.375 1.594,0.25 10 false - Throttle Valve Control 1.24,1.438 2.219,1.698 0.979,0.26 10 false Vehicle Ahead 0.771,3.01 1.75,3.271 0.979,0.26 10 false Own Vehicle 5.135,2.823 6.729,3.073 1.594,0.25 10 false Throttle Control Motor


5.

Stop Control Function (Models with Full-speed Range Following Function)

(a)

During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the forward recognition camera maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary driving force to stop the vehicle, and sends a drive request signal to the hybrid vehicle control ECU and skid control ECU. When the hybrid vehicle control ECU and skid control ECU receive this signal, they control the driving force and stop the vehicle.

(b)

At this time, the skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.

(c)

The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the distance control switch.

Y230950E01
1.833,0.354 3.667,0.76 1.833,0.406 10 false Forward Recognition Camera 4.865,0.385 6.74,0.792 1.875,0.406 10 false Millimeter Wave Radar Sensor Assembly 3.021,2.438 4.396,2.958 1.375,0.521 10 false Hybrid Vehicle Control ECU 5.156,1.458 6.521,1.781 1.365,0.323 10 false Acceleration Control 5.708,1.969 6.448,2.219 0.74,0.25 10 false MG ECU 5.563,2.26 6.729,2.469 1.167,0.208 10 false - MG Control 5.771,2.719 6.188,2.917 0.417,0.198 10 false ECM 5.344,3.323 6.823,3.542 1.479,0.219 10 false - Throttle Valve Control 4.583,3.885 6.063,4.094 1.479,0.208 10 false Deceleration Control 3.823,4.771 5.01,5 1.188,0.229 10 false Skid Control ECU 5.844,4.792 6.854,5.031 1.01,0.24 10 false Stop Light On 0.896,4.26 2.083,4.49 1.188,0.229 10 false Vehicle Behind 0.896,1.833 2.083,2.063 1.188,0.229 10 false Vehicle Ahead 0.896,3.115 2.083,3.344 1.188,0.229 10 false Own Vehicle 5.271,3.01 6.75,3.229 1.479,0.219 10 false Throttle Control Motor


6.

Stop Retention Control Function (Models with Full-speed Range Following Function)

(a)

After the vehicle has stopped under stop control, hybrid vehicle control ECU transmits a stop retention request signal to the skid control ECU. Upon receiving this signal, the skid control ECU activates the brake hold function and keeps the vehicle stopped.

HINT:

If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.


Y230951E01
3.042,2.229 4.417,2.833 1.375,0.604 10 false Hybrid Vehicle Control ECU 1.552,0.427 3.49,0.729 1.938,0.302 10 false Forward Recognition Camera 4.292,0.438 6.844,0.885 2.552,0.448 10 false Millimeter Wave Radar Sensor Assembly 1.052,1.802 2.104,2.198 1.052,0.396 10 false Vehicle Ahead 0.99,3.281 2.042,3.677 1.052,0.396 10 false Own Vehicle 4.26,3.302 5.833,3.563 1.573,0.26 10 false Stop Retention Control 3.427,3.781 4.583,4.052 1.156,0.271 10 false Skid Control ECU 3.49,4.104 4.646,4.375 1.156,0.271 10 false - Brake Control 5.573,3.729 6.729,4 1.156,0.271 10 false Stop Holding 5.604,4.188 6.583,4.458 0.979,0.271 10 false Stop Light On


7.

Start Control Function (Models with Full-speed Range Following Function)

(a)

When the forward recognition camera detects that the vehicle ahead starts moving again from the millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).

(b)

Upon receiving the start-off operation signal generated by pushing the +RES switch on the steering pad switch assembly or by depressing the accelerator pedal, the forward recognition camera transmits a motive force request signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU controls the motive force, starts the vehicle and resumes follow-up control.

HINT:

Pressing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.


Y230952E02
1.688,0.25 3.5,0.594 1.813,0.344 10 false Forward Recognition Camera 4.729,0.219 6.625,0.688 1.896,0.469 10 false Millimeter Wave Radar Sensor Assembly 3.208,1.406 7.146,1.823 3.938,0.417 10 false Start-off Operation Request Display on Multi-information Display 3.823,2.167 6.5,2.458 2.677,0.292 10 false Steering Pad Switch (+RES Switch Signal) 3.5,1.781 5.771,1.969 2.271,0.188 10 false Accelerator Pedal Operation Signal 2.688,3.615 4.063,4 1.375,0.385 10 false Hybrid Vehicle Control ECU 5.24,3.531 6.271,3.74 1.031,0.208 10 false - MG2 Control 5.406,3.229 6.396,3.385 0.99,0.156 10 false MG ECU 5.073,2.802 6.604,3 1.531,0.198 10 false Acceleration Control 5.573,3.99 6.115,4.25 0.542,0.26 10 false ECM 5.146,4.573 6.646,4.771 1.5,0.198 10 false - Throttle Valve Control 4.333,5.063 6.052,5.313 1.719,0.25 10 false Stop Retention Control 3.385,5.667 5.104,5.917 1.719,0.25 10 false Skid Control ECU 3.448,6.104 4.688,6.354 1.24,0.25 10 false - Brake Control 5.865,5.604 6.719,5.844 0.854,0.24 10 false Stop Holding 5.854,6.115 6.833,6.344 0.979,0.229 10 false Stop Light Off 0.74,4.521 1.802,4.76 1.063,0.24 10 false Own Vehicle 0.75,2.625 1.813,2.865 1.063,0.24 10 false Vehicle Ahead 5.094,4.292 6.594,4.49 1.5,0.198 10 false Throttle Control Motor


8.

Turn signal-linked Control Function

(a)

If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed.

Y230953E01
1.781,0.698 2.813,0.906 1.031,0.208 10 false Vehicle Ahead 4,0.719 5.031,0.927 1.031,0.208 10 false Vehicle Ahead 6.354,0.365 6.854,0.75 0.5,0.385 10 false Vehicle Ahead 1.75,2.875 2.781,3.083 1.031,0.208 10 false Own Vehicle 3.948,2.458 4.979,2.667 1.031,0.208 10 false Own Vehicle 4.729,2.083 5.521,2.333 0.792,0.25 10 false Own Vehicle 2.927,4.031 5.49,4.281 2.563,0.25 10 false Millimeter Wave Radar Sensor Assembly 3.583,4.948 4.885,5.198 1.302,0.25 10 false Turn Signal Switch 2.469,6.469 3.854,7.042 1.385,0.573 10 false Hybrid Vehicle Control ECU 4.635,5.604 6.031,5.875 1.396,0.271 10 false Acceleration Control 5.031,6.042 5.771,6.313 0.74,0.271 10 false MG ECU 4.885,6.344 6.063,6.542 1.177,0.198 10 false - MG2 Control 5.219,6.781 6.396,6.979 1.177,0.198 10 false ECM 4.667,7.083 6.458,7.271 1.792,0.188 10 false Throttle Control Motor 0.75,5.531 2.031,5.896 1.281,0.365 10 false Forward Recognition Camera 4.896,7.354 6.563,7.573 1.667,0.219 10 false - Throttle Valve Control


9.

Dynamic Radar Cruise Control with Road Sign Assist (Models with RSA System)

(a)

This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit.

Y230954E02
3.833,0.271 6.719,0.844 2.885,0.573 10 false Operation Request Display on Multi-information Display 5.104,1.01 6.781,1.281 1.677,0.271 10 false +RES/-SET Switch Signal 5.385,1.563 6.688,1.885 1.302,0.323 10 false Acceleration Control 5.698,2 6.406,2.25 0.708,0.25 10 false MG ECU 5.542,2.292 6.51,2.531 0.969,0.24 10 false - MG2 Control 5.885,2.74 6.5,2.979 0.615,0.24 10 false ECM 5.385,3.021 6.792,3.292 1.406,0.271 10 false Throttle Control Motor 3.323,2.542 4.698,2.958 1.375,0.417 10 false Hybrid Vehicle Control ECU 1.344,2.615 2.635,3.031 1.292,0.417 10 false Forward Recognition Camera 5.438,3.292 7.063,3.521 1.625,0.229 10 false - Throttle Valve Control




iv.

Automatic Cancel Control

·

If one of the conditions listed below occurs while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.

Constant Speed Control Mode
Situation Warning
Multi-information Display Buzzer

*: Except models with full-speed range following function

If the following condition occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.


The cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed.


- -
If the following condition occurs, the hybrid vehicle control ECU cancels the cruise control while retaining the set vehicle speed in its memory.*
·

The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)].


- -
If the following condition occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the hybrid control system.


The cruise control system is disabled until the power switch is turned on (IG) again.
- -
If either of the conditions listed below occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

Stop light switch assembly input signal is abnormal.

·

Cancel circuit malfunction.

·

Brake control system malfunction.

·

Communication malfunction between the skid control ECU and hybrid vehicle control ECU.


Cruise Control
Malfunction
Visit Your Dealer
Sounds

Vehicle-to-vehicle Distance Control Mode
Situation Warning
Multi-information Display Buzzer

*: Except models with full-speed range following function

If either of the conditions listed below occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.

·

Malfunction of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.*

·

Malfunction in the dynamic radar cruise control system other than those given above.


The cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the hybrid vehicle control ECU clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the hybrid control system.


The cruise control system is disabled until the power switch is turned on (IG) again.
- -
If the following condition occurs, the hybrid vehicle control ECU cancels the cruise control while retaining the set vehicle speed in its memory.
·

The millimeter wave radar sensor assembly or the grille cover are dirty.


The cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Temporarily Unavailable
See Owner's Manual
Sounds
If either of the following conditions occurs, the hybrid vehicle control ECU cancels the cruise control while retaining the set vehicle speed in its memory.
·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


The cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Unavailable
Sounds
If any of the following conditions occur while the vehicle stopped, the hybrid vehicle control ECU cancels the cruise control system.*
·

An open or short circuit in the stop light switch assembly.

·

Malfunction in the millimeter wave radar sensor assembly.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.

·

The millimeter wave radar sensor assembly or the grille cover are dirty.

·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


Cruise Control Fault
Press Brake to
Deactivate
Visit Your Dealer
Sounds
If the following conditions occur while the vehicle stopped, the hybrid vehicle control ECU cancels the cruise control system.*
·

The vehicle is stopped on a steep hill.


Radar Cruise
Control
Unavailable
Press Brake to
Resume Driving
-
If the following conditions occur while the vehicle stopped, the hybrid vehicle control ECU cancels the cruise control system.*
·

The driver seat belt is unfastened.

·

The driver side door is opened.

·

The vehicle is parked for a long period of time.


- -




b.

System Control for Gasoline Models

i.

The control of the dynamic radar cruise control system varies depending on the mode:

A: Constant Speed Control Mode

B: Vehicle-to-vehicle Distance Control Mode (Models without full-speed range following function)

C: Vehicle-to-vehicle Distance Control Mode (Models with full-speed range following function)

Function Outline Mode
A B C

○: Available

-: Not available

x: Not setting

*1: Models with RSA system

*2: Except models for Europe

*3: Models for Europe

*4: Models with automatic transaxle

*5: Models with shift paddle switch

*6: Models with downhill assist control

*7: 4WD/AWD models

Constant Speed Control The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle motor to increase the throttle valve opening angle. ○ ○ ○
Deceleration Control Performs throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance. - ○ ○
Follow-up Control After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance. The actual distance maintained for each distance level (long, medium and short) varies in accordance with the vehicle speed. - ○ ○
Acceleration Control Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. - ○ ○
Stop Control Detects if the vehicle ahead has stopped, performs motive force control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. - - ○
Stop Retention Control Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. - - ○
Start Control Detects that the vehicle ahead starts moving again, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch on the steering pad switch assembly or depress the accelerator pedal), and resumes follow-up control after the vehicle is started. - - ○
Turn signal-linked Control If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed. - ○ ○
Dynamic Radar Cruise Control with Road Sign Assist*1 This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit. - x ○
Set Control When the dynamic radar cruise control system has been turned on using the cruise control switch on the steering pad switch assembly, either of the relevant vehicle speed conditions shown below is met, and the -SET switch on the steering pad switch assembly is pressed, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed. ○ ○ ○
The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or more. ○ ○ ○
When the vehicle is traveling at a speed of approximately 30 km/h (20 mph) or less and a vehicle ahead is detected, the set vehicle speed is set to the low speed limit [approximately 30 km/h (20 mph)]. - - ○
Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. ○ ○ -
COAST Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle decelerates constantly.

·

The set vehicle speed changes to the speed at which the -SET switch is released.


○ - -
·

The set vehicle speed decreases in increments of 5 km/h or 5 mph. [Example: 103 →100 → 95 → 90 → 85 km/h (mph)]

·

The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released.


- ○ ○
Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was being driven at the time the -SET switch was operated.


○ - -
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is pushed.*2

·

The vehicle will decelerate in increments of approximately 5 km/h or 5 mph for each time the -SET switch is pushed.*3


- ○ ○
Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will accelerate constantly.

·

The set vehicle speed changes to the speed at which the +RES switch is released.


○ - -
·

The set vehicle speed increases in increments of 5 km/h or 5 mph. [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)]

·

The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set vehicle speed will change during follow-up control.


- ○ ○
Resume Control If the vehicle speed is above the low speed limit, the +RES switch on the steering pad switch assembly can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. ○ ○ ○
Even if the vehicle speed drops below the low speed limit, resumption can be performed when the vehicle speed increases to above the low speed limit. However, resumption can be performed even if the vehicle speed is below the low speed limit when the vehicle is running in mode B and there is a vehicle ahead. - - ○
If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by pushing the +RES switch on the steering pad switch assembly. - ○ ○
After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the steering pad switch assembly is pushed to the +RES switch, follow-up control is resumed and the vehicle can be accelerated up to the set speed. - - ○
Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows: ○ ○ ○
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.


○ - -
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is pushed.*2

·

The vehicle will accelerate in increments of approximately 5 km/h or 5 mph for each time the +RES switch is pushed.*3


- ○ ○
Shift-down Control*4 When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift down control, when the end of uphill travel is determined based on the throttle valve angle, the transmission will shift up after a certain period of time. When the transmission shifts down during accelerator control or resume control, the transmission will shift up after accelerator control or resume control ends. ○ ○ ○
Manual Cancel Control Models with Automatic Transaxle
If any of the following signals are sent to the ECM, the cruise control is canceled accordingly:
·

Stop light switch on signal. (The brake pedal is depressed)

·

Shift lever is moved from D or S to any other position.

·

When 1st, 2nd or 3rd range is selected in S position by shift lever.

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (transmission shift switch assembly).*5

·

CANCEL switch on signal. (CANCEL switch on the steering pad switch assembly is pushed)

·

Cruise control switch off signal. (Cruise control switch on the steering pad switch assembly is pushed)

·

Electric parking brake is applied. (During vehicle-to-vehicle distance control mode)


○ ○ ○
Models with CVT
If any of the following signals are sent to the ECM, the cruise control is canceled accordingly:
·

Stop light switch on signal. (The brake pedal is depressed)

·

Shift lever is moved from D or M to any other position.

·

When 1st, 2nd or 3rd range is selected in M position by shift lever.

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (transmission shift switch assembly).*5

·

CANCEL switch on signal. (CANCEL switch on the steering pad switch assembly is pushed)

·

Cruise control switch off signal. (Cruise control switch on the steering pad switch assembly is pushed)

·

Electric parking brake is applied. (During vehicle-to-vehicle distance control mode)


○ ○ ○
Models with Manual Transaxle
If any of the following signals are sent to the ECM, the cruise control is canceled accordingly:
·

Stop light switch on signal. (The brake pedal is depressed)

·

Move the shift lever to 1st gear or reverse gear.

·

Neutral position switch is detecting neutral for more than a specified time.

·

Depress the clutch pedal. (Constant speed control mode)

·

During shift operation, the clutch pedal is depressed for more than the specified amount of time. (Vehicle-to-vehicle distance control mode)

·

CANCEL switch on signal. (CANCEL switch on the steering pad switch assembly is pushed)

·

Cruise control switch off signal. (Cruise control switch on the steering pad switch assembly is pushed)

·

Electric parking brake is applied. (During vehicle-to-vehicle distance control mode)


○ ○ x
Automatic Cancel Control When an automatic cancel signal is sent to the ECM, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. ○ ○ ○
Mode Switching Control The following operations switch modes:
·

Vehicle-to-vehicle distance control mode is activated immediately after the switch is turned on. The mode is changed to constant speed control mode by pressing and holding the switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off.


○ ○ ○
Other Cancel Conditions
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time while the cruise control.

·

TRC is off or VSC is off.

·

Ignition switch off.

·

Pre-collision system operates during cruise control driving.

·

Downhill assist control switch is turned on*6

·

Off-road mode is selected by the multi-terrain select switch*7

·

Drive start control operates during cruise control driving. (During vehicle-to-vehicle distance control mode)

·

Parking support brake system operates during cruise control driving. (During vehicle-to-vehicle distance control mode)

·

Electric parking brake system operates during cruise control driving. (During vehicle-to-vehicle distance control mode)


○ ○ ○
Diagnosis If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the ECM cancels cruise control and memorizes information related to the malfunction. ○ ○ ○


ii.

Constant Speed Control Mode

·

The ECM compares the set vehicle speed and the actual vehicle speed, and performs constant speed control in order to attain the set vehicle speed.



iii.

Vehicle-to-vehicle Distance Control Mode

·

In vehicle-to-vehicle distance control mode, the ECM performs constant speed control function, deceleration control function, follow-up control function, acceleration control function, stop control function*, stop retention control function*, start control function* or turn signal-linked control function based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.

*: Models with full-speed range following function



1.

Constant Speed Control Function

(a)

The ECM compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the throttle in order to attain the set vehicle speed. The forward recognition camera uses the millimeter wave radar sensor signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the ECM.

Y230933E01
1.823,0.344 3.74,0.719 1.917,0.375 10 false Forward Recognition Camera 4.823,0.365 6.719,0.802 1.896,0.438 10 false Millimeter Wave Radar Sensor Assembly 3.323,2.438 3.729,2.802 0.406,0.365 10 false ECM 5.125,1.938 6.5,2.208 1.375,0.271 10 false Acceleration Control 5.177,2.396 6.552,2.667 1.375,0.271 10 false Throttle Control Motor 5.167,2.719 6.615,2.938 1.448,0.219 10 false - Throttle Valve Control 0.771,2.615 1.813,2.854 1.042,0.24 10 false Own Vehicle


2.

Deceleration Control Function

(a)

The forward recognition camera calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor, forward recognition camera and transmits a deceleration request signal to the ECM. Upon receiving this signal, the ECM closes the throttle valve in order to cause the vehicle to decelerate.

(b)

This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.

Y230934E01
1.156,0.26 3.073,0.521 1.917,0.26 10 false Forward Recognition Camera 4.854,0.271 6.729,0.677 1.875,0.406 10 false Millimeter Wave Radar Sensor Assembly 3.469,2.365 3.948,2.698 0.479,0.333 10 false ECM 5.135,1.802 6.594,2.031 1.458,0.229 10 false Acceleration Control 5.188,2.25 6.646,2.479 1.458,0.229 10 false Throttle Control Motor 5.229,2.563 6.688,2.792 1.458,0.229 10 false - Throttle Valve Control 5.135,3.417 6.594,3.646 1.458,0.229 10 false Deceleration Control 5.365,3.958 6.823,4.188 1.458,0.229 10 false Skid Control ECU 5.458,4.25 6.917,4.479 1.458,0.229 10 false - Brake Control 0.76,3.531 2.396,3.792 1.635,0.26 10 false Own Vehicle 0.771,1.521 1.844,1.75 1.073,0.229 10 false Vehicle Ahead

(c)

If the forward recognition camera determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.

(d)

At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.

Y230935E01
1.208,0.25 3.104,0.677 1.896,0.427 10 false Forward Recognition Camera 4.885,0.25 6.781,0.688 1.896,0.438 10 false Millimeter Wave Radar Sensor Assembly 3.531,2.375 4.031,2.75 0.5,0.375 10 false ECM 5.198,1.854 6.813,2.042 1.615,0.188 10 false Acceleration Control 5.24,2.229 6.854,2.417 1.615,0.188 10 false Throttle Control Motor 5.302,2.563 6.833,2.792 1.531,0.229 10 false - Throttle Valve Control 5.229,3.396 6.844,3.583 1.615,0.188 10 false Deceleration Control 5.417,3.896 6.656,4.125 1.24,0.229 10 false Skid Control ECU 5.521,4.188 6.646,4.458 1.125,0.271 10 false - Brake Control 0.823,2.635 1.896,2.844 1.073,0.208 10 false Own Vehicle 0.833,1.281 1.906,1.49 1.073,0.208 10 false Vehicle Ahead 0.844,3.75 1.917,3.958 1.073,0.208 10 false Vehicle Behind

(e)

If the vehicle is not decelerating adequately, ECM sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.

Y230936E01
1.99,0.198 3.271,0.615 1.281,0.417 10 false Forward Recognition Camera 4.74,0.208 6.656,0.76 1.917,0.552 10 false Millimeter Wave Radar Sensor Assembly 5.479,1.25 6.323,1.5 0.844,0.25 10 false Warning 5.573,1.646 6.146,1.854 0.573,0.208 10 false Buzzer 3.344,3.219 4.625,3.635 1.281,0.417 10 false ECM 5.229,2.677 6.615,3.01 1.385,0.333 10 false Acceleration Control 5.24,3.104 6.708,3.323 1.469,0.219 10 false Throttle Control Motor 5.281,3.417 6.833,3.698 1.552,0.281 10 false - Throttle Valve Control 5.219,4.271 6.604,4.604 1.385,0.333 10 false Deceleration Control 5.271,4.823 6.656,5.156 1.385,0.333 10 false Skid Control ECU 5.323,5.167 6.708,5.5 1.385,0.333 10 false - Brake Control 0.76,3.635 2.042,4.052 1.281,0.417 10 false Vehicle Behind 0.792,2.615 2.073,3.031 1.281,0.417 10 false Own Vehicle 0.844,1.24 1.865,1.615 1.021,0.375 10 false Vehicle Ahead


3.

Follow-up Control Function

(a)

After performing deceleration control, the forward recognition camera transmits a request signal to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform follow-up control.

(b)

3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.

Y230937E01
1.688,0.417 3.563,0.823 1.875,0.406 10 false Forward Recognition Camera 4.896,0.417 6.771,0.823 1.875,0.406 10 false Millimeter Wave Radar Sensor Assembly 4.75,1.469 6.865,1.771 2.115,0.302 10 false Steering Pad Switch Assembly 4.99,2 6.656,2.49 1.667,0.49 10 false Vehicle-to-vehicle Distance Control Switch 3.385,3.521 3.802,3.844 0.417,0.323 10 false ECM 5.167,2.917 6.552,3.156 1.385,0.24 10 false Acceleration Control 5.156,3.344 6.677,3.563 1.521,0.219 10 false Throttle Control Motor 5.177,3.625 6.656,3.896 1.479,0.271 10 false - Throttle Valve Control 5.094,4.177 6.573,4.448 1.479,0.271 10 false Deceleration Control 5.313,4.688 6.458,4.917 1.146,0.229 10 false Skid Control ECU 5.448,5.031 6.594,5.26 1.146,0.229 10 false - Brake Control 0.74,3.635 1.625,3.885 0.885,0.25 10 false Own Vehicle 0.896,2.74 1.99,3.115 1.094,0.375 10 false Vehicle-to-vehicle Distance 0.76,1.76 1.781,2.01 1.021,0.25 10 false Vehicle Ahead


4.

Acceleration Control Function

(a)

If the forward recognition camera detects (based on the millimeter wave radar sensor and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform acceleration control.

Y230938E01
1.885,0.448 3.719,0.865 1.833,0.417 10 false Forward Recognition Camera 4.854,0.5 6.74,0.917 1.885,0.417 10 false Millimeter Wave Radar Sensor Assembly 3.365,2.677 4.135,3.063 0.771,0.385 10 false ECM 5.063,2.198 6.625,2.438 1.563,0.24 10 false Acceleration Control 5.094,2.677 6.656,2.917 1.563,0.24 10 false Throttle Control Motor 5.167,2.979 6.729,3.219 1.563,0.24 10 false - Throttle Valve Control 0.792,2.979 1.698,3.292 0.906,0.313 10 false Own Vehicle 1.26,1.479 2.208,1.75 0.948,0.271 10 false Vehicle Ahead


5.

Stop Control Function (Models with Full-speed Range Following Function)

(a)

During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the forward recognition camera maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary driving force to stop the vehicle, and sends a drive request signal to the ECM and skid control ECU. When the ECM and skid control ECU receive this signal, they control the driving force and stop the vehicle.

(b)

At this time, the skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.

(c)

The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the distance control switch.

Y230939E01
1.948,0.365 3.844,0.729 1.896,0.365 10 false Forward Recognition Camera 4.823,0.396 6.698,0.854 1.875,0.458 10 false Millimeter Wave Radar Sensor Assembly 3.552,2.698 4.073,3.042 0.521,0.344 10 false ECM 5.188,2.156 6.677,2.396 1.49,0.24 10 false Acceleration Control 5.323,2.552 6.813,2.792 1.49,0.24 10 false Throttle Control Motor 5.354,2.844 6.844,3.083 1.49,0.24 10 false - Throttle Valve Control 0.958,2.229 2.104,2.427 1.146,0.198 10 false Vehicle Ahead 0.906,3.135 2.052,3.333 1.146,0.198 10 false Own Vehicle 0.875,4.135 2.021,4.333 1.146,0.198 10 false Vehicle Behind 3.823,4.458 4.969,4.656 1.146,0.198 10 false Skid Control ECU 3.979,4.885 5.125,5.083 1.146,0.198 10 false - Brake Control 5.875,4.771 6.781,5.01 0.906,0.24 10 false Stop Light On 4.427,3.906 5.75,4.146 1.323,0.24 10 false Deceleration Control


6.

Stop Retention Control Function (Models with Full-speed Range Following Function)

(a)

After the vehicle has stopped under stop control, the ECM transmits a stop retention request signal to the skid control ECU. Upon receiving this signal, the skid control ECU activates the brake hold function and keeps the vehicle stopped.

HINT:

If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.


Y230940E01
1.479,0.448 3.458,0.75 1.979,0.302 10 false Forward Recognition Camera 4.604,0.427 6.469,0.885 1.865,0.458 10 false Millimeter Wave Radar Sensor Assembly 3.531,2.344 4.01,2.635 0.479,0.292 10 false ECM 4.229,3.302 5.781,3.51 1.552,0.208 10 false Stop Retention Control 3.521,3.771 4.677,4 1.156,0.229 10 false Skid Control ECU 3.542,4.125 4.531,4.375 0.99,0.25 10 false - Brake Control 5.625,3.75 6.531,4.042 0.906,0.292 10 false Stop Holding 5.615,4.188 6.521,4.479 0.906,0.292 10 false Stop Light On 0.917,1.938 2.042,2.115 1.125,0.177 10 false Vehicle Ahead 0.938,2.906 1.948,3.208 1.01,0.302 10 false Own Vehicle


7.

Start Control Function (Models with Full-speed Range Following Function)

(a)

When the forward recognition camera detects that the vehicle ahead starts moving again millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).

(b)

Upon receiving the start-off operation signal generated by pushing the +RES switch on the steering pad switch assembly or by depressing the accelerator pedal, the forward recognition camera transmits a motive force request signal to the ECM. Upon receiving this signal, the ECM controls the motive force, starts the vehicle and resumes follow-up control.

(c)

During idle stop status, engine starts automatically when the ECU detects the movement of preceding vehicle.

HINT:

Pressing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.


Y230941E02
1.667,0.229 3.604,0.521 1.938,0.292 10 false Forward Recognition Camera 4.51,0.208 7.042,0.469 2.531,0.26 10 false Millimeter Wave Radar Sensor Assembly 3.219,1.531 7.146,1.958 3.927,0.427 10 false Start-off Operation Request Display on Multi-information Display 3.5,2.104 5.969,2.375 2.469,0.271 10 false Accelerator Pedal Operation Signal 3.813,2.708 6.615,3 2.802,0.292 10 false Steering Pad Switch (+RES Switch Signal) 3.25,3.833 3.844,4.167 0.594,0.333 10 false ECM 5.188,3.719 6.646,4 1.458,0.281 10 false Throttle Control Motor 5.083,3.313 6.542,3.594 1.458,0.281 10 false Acceleration Control 5.188,4.021 6.646,4.302 1.458,0.281 10 false - Throttle Valve Control 0.854,2.802 1.833,3.042 0.979,0.24 10 false Vehicle Ahead 0.76,4.26 1.74,4.5 0.979,0.24 10 false Own Vehicle 4.094,4.979 6.177,5.24 2.083,0.26 10 false Stop Retention Control 3.417,5.51 4.729,5.844 1.313,0.333 10 false Skid Control ECU 3.5,5.979 4.813,6.313 1.313,0.333 10 false - Brake Control 5.885,5.604 6.76,5.938 0.875,0.333 10 false Stop Holding 5.896,6.125 6.833,6.375 0.938,0.25 10 false Stop Light Off


8.

Turn signal-linked Control Function

(a)

If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed.

Y230942E01
1.792,0.792 2.844,1 1.052,0.208 10 false Vehicle Ahead 1.74,2.896 2.792,3.104 1.052,0.208 10 false Own Vehicle 4.135,0.823 5.188,1.031 1.052,0.208 10 false Vehicle Ahead 6.375,0.979 6.906,1.458 0.531,0.479 10 false Vehicle Ahead 3.979,2.542 4.875,2.771 0.896,0.229 10 false Own Vehicle 4.698,2.063 5.51,2.281 0.813,0.219 10 false Own Vehicle 3.406,4.948 4.896,5.146 1.49,0.198 10 false Turn Signal Switch 2.927,4.052 5.51,4.302 2.583,0.25 10 false Millimeter Wave Radar Sensor Assembly 4.594,5.927 6.083,6.125 1.49,0.198 10 false Acceleration Control 3.073,6.656 3.448,6.896 0.375,0.24 10 false ECM 4.667,6.458 6.292,6.646 1.625,0.188 10 false Throttle Control Motor 4.75,6.813 6.385,7.104 1.635,0.292 10 false - Throttle Valve Control 0.99,5.552 2.302,5.958 1.313,0.406 10 false Forward Recognition Camera


9.

Dynamic Radar Cruise Control with Road Sign Assist (Models with RSA System)

(a)

This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit.

Y230943E02
4.073,0.302 6.948,0.719 2.875,0.417 10 false Operation Request Display on Multi-information Display 4.813,1.031 6.469,1.302 1.656,0.271 10 false +RES/-SET Switch Signal 5.406,1.875 6.833,2.146 1.427,0.271 10 false Acceleration Control 3.948,2.625 4.323,2.969 0.375,0.344 10 false ECM 5.354,2.438 6.708,2.719 1.354,0.281 10 false Throttle Control Motor 5.458,2.76 6.927,3.021 1.469,0.26 10 false - Throttle Valve Control 1.792,2.604 3.094,3.052 1.302,0.448 10 false Forward Recognition Camera




iv.

Automatic Cancel Control

·

If one of the conditions listed below occurs while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.

Constant Speed Control Mode
Situation Warning
Multi-information Display Buzzer

*: Except models with full-speed range following function

If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.


The cruise control system is disabled until the ignition switch is turned on again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed.


- -
If the following condition occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.*
·

The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)].


- -
If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the engine control system.


The cruise control system is disabled until the ignition switch is turned on again.
- -
If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

Stop light switch assembly input signal is abnormal.

·

Cancel circuit malfunction.

·

Brake control system malfunction.

·

Communication malfunction between the skid control ECU and ECM.


Cruise Control
Malfunction
Visit Your Dealer
Sounds

Vehicle-to-vehicle Distance Control Mode
Situation Warning
Multi-information Display Buzzer

*: Except models with full-speed range following function

If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.

·

Malfunction of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.*

·

Malfunction in the dynamic radar cruise control system other than those given above.


The cruise control system is disabled until the ignition switch is turned on again.
Cruise Control
Malfunction
Visit Your Dealer
Sounds
If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the engine control system.


The cruise control system is disabled until the ignition switch is turned on again.
- -
If the following condition occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·

The millimeter wave radar sensor assembly or the grille cover are dirty.


The cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Temporarily Unavailable
See Owner's Manual
Sounds
If either of the following conditions occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


The cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Unavailable
Sounds
If any of the following conditions occur while the vehicle stopped, the ECM cancels the cruise control system.*
·

An open or short circuit in the stop light switch assembly.

·

Malfunction in the millimeter wave radar sensor assembly.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

The brake holding control system is malfunction.

·

The millimeter wave radar sensor assembly or the grille cover are dirty.

·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


Cruise Control Fault
Press Brake to
Deactivate
Visit Your Dealer
Sounds
If the following conditions occur while the vehicle stopped, the ECM cancels the cruise control system.*
·

The vehicle is stopped on a steep hill.


Radar Cruise
Control
Unavailable
Press Brake to
Resume Driving
-
If the following conditions occur while the vehicle stopped, the ECM cancels the cruise control system.*
·

The driver seat belt is unfastened.

·

The driver side door is opened.

·

The vehicle is parked for a long period of time.


- -





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.