Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2018.10–2019.02
NM3620E _58 Vehicle Interior _076457 PRE-COLLISION _0377069 PRE-COLLISION SYSTEM GE GENERAL F

PRE-COLLISION  PRE-COLLISION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Toyota Safety Sense

i.

The preventive safety package "Toyota Safety Sense" is used to support safe driving.


ii.

Systems that are included in the "Toyota Safety Sense" are as follows:

Toyota Safety Sense
·

Pre-collision System (PCS)

·

Dynamic Radar Cruise Control System

·

Lane Tracing Assist (LTA) System

·

Lane Departure Alert (LDA) System

·

Road Sign Assist (RSA) System

·

Automatic High Beam (AHB)





b.

Pre-collision System (PCS)

i.

The pre-collision system helps to lessen the damage sustained in a collision by operating in unison with warning devices and brake systems.


ii.

The pre-collision system detects the vehicle, pedestrian* and bicycle riders* in front of the vehicle based on data from both a forward recognition camera and millimeter wave radar sensor assembly.

HINT:

*: Depending on the region in which the vehicle was sold, the pedestrian detection function and bicycle riders detection function may not be available.

Detectable Objects
Regions Detectable Objects Destination/Countries

*1: Except models for Jordan and Lebanon

*2: Except models for Azerbaijan, Georgia and Armenia

*3: Except models for Taiwan

Region A
·

Vehicles

·

Pedestrians

·

Bicycle Riders


·

Korea

·

G.C.C. Countries*1

·

Australia

·

South Africa

·

Europe*2


Region B
·

Vehicles

·

Pedestrians


·

Taiwan


Region C
·

Vehicles


·

Jordan

·

Lebanon

·

Azerbaijan

·

Georgia

·

Armenia

·

General Countries*3





iii.

If the pre-collision system determines that the possibility of a collision is high, pre-collision warning control and pre-collision brake assist control is performed, and if a collision is imminent, pre-collision braking control will be performed to help avoid and reduce the impact of the collision.




PRECAUTION


a.

Ignition Switch Expressions (For Gasoline Models)

i.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch
(Position)
Engine Switch
(Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



b.

Toyota Safety Sense

i.

The Toyota Safety Sense is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions.


ii.

As there is a limit to the degree of recognition accuracy and control performance that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention to the vehicle's surroundings and driving safely.



c.

Limitations of the pre-collision system

i.

The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. Do not use the pre-collision system instead of normal braking operations under any circumstances. This system will not prevent collisions or lessen collision damage or injuries in every situation. Do not overly rely on this system. Failure to do so may lead to an accident, resulting in death or serious injury.


ii.

Although this system is designed to help avoid a collision or help reduce the impact of the collision, its effectiveness may change according to various conditions, therefore the system may not always be able to achieve the same level of performance. Do not overly rely on this system and always drive carefully.


iii.

Do not attempt to test the operation of the pre-collision system yourself, as the system may not operate properly, possibly leading to an accident.



d.

Pre-collision braking

i.

When the pre-collision braking function is operating, a large amount of braking force will be applied.


ii.

If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.


iii.

The pre-collision braking function may not operate if certain operations are performed by the driver. If the accelerator pedal is being depressed strongly or the steering wheel is being turned, the system may determine that the driver is taking evasive action and possibly prevent the pre-collision braking function from operating.


iv.

In some situations, while the pre-collision braking function is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly or the steering wheel is turned and the system determines that the driver is taking evasive action.


v.

If the brake pedal is being depressed, the system may determine that the driver is taking evasive action and possibly delay the operation timing of the pre-collision braking function.



e.

When to disable the pre-collision system

i.

In the following situations, disable the system, as it may not operate properly, possibly leading to an accident resulting in death or serious injury:

*1: HV models

*2: Gasoline models

·

When the vehicle is being towed

·

When your vehicle is towing another vehicle

·

When transporting the vehicle via truck, boat, train or similar means of transportation

·

When the vehicle is raised on a lift with the hybrid system on and the tires are allowed to rotate freely*1

·

When the vehicle is raised on a lift with the engine running and the tires are allowed to rotate freely*2

·

When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on-vehicle wheel balancer

·

When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons

·

If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning

·

When the vehicle is driven in a sporty manner or off-road

·

When the tires are not properly inflated

·

When the tires are very worn

·

When tires of a size other than specified are installed

·

When tire chains are installed

·

When a compact spare tire or an emergency tire puncture repair kit is used

·

If equipment (snow plow, etc.) that may obstruct the millimeter wave radar sensor assembly or forward recognition camera is temporarily installed to the vehicle





f.

Object detection function

i.

The pre-collision system uses the millimeter wave radar sensor assembly and forward recognition camera to detect operation targets based off the size, outline and movement of vehicles, pedestrians and pedestrians riding bicycles.


ii.

Depending on the brightness of the surrounding environment and the movement, posture and angle of the operation target, the operation target may not be detected and the system may not operate properly.

Y227332

HINT:

Depending on the region in which the vehicle was sold, the pedestrian detection function and bicycle riders detection function may not be available.




g.

Situations in which the system may not operate properly

i.

In the following conditions, operation targets cannot be detected by the millimeter wave radar sensor assembly and forward recognition camera, so the system may not operate normally.

*1: Depending on the region in which the vehicle was sold, the pedestrian detection function and bicycle riders detection function may not be available.

*2: HV models

*3: Gasoline models

·

When another vehicle approaches own vehicle from the front

·

When the vehicle or operation target is driving erratically

·

When the operation target performs a sudden movement (sudden steering wheel operation, sudden acceleration, sudden deceleration, etc.)

·

When the vehicle suddenly approaches an operation target

·

When the operation target is not aligned with the center of the vehicle [Case 1]

·

When the operation target is near a wall, fence, guardrail, manhole, steel plate on the road or another vehicle, etc.

·

When the operation target is under a structure

·

When part of the operation target is hidden by another object (such as large luggage, umbrellas or a guardrail)

·

When several operation targets are grouped together

·

When sunlight is reflecting brightly off of the operation target

·

When the operation target is a shade of white or extremely bright

·

When the color of the operation target blends into the background

·

When an operation target cuts in or suddenly emerges from the side

·

When snow, water, etc., is kicked up in front of the vehicle

·

When strong light from a preceding vehicle (such as sunlight or the headlights of another vehicle) strikes the lens on the forward recognition camera

·

When approaching a preceding vehicle that is moving towards, or facing the vehicle

·

When the preceding vehicle is a motorcycle or bicycle*1

·

When the width of the preceding vehicle is narrow (such as an ultra-small mobility vehicle)

·

When the rear end area of the preceding vehicle is small (such as a truck with no load)

·

When the rear end of the preceding vehicle is in a low position (such as a low bed trailer) [Case 2]

·

When the minimum ground clearance of the preceding vehicle is extremely high [Case 3]

·

When luggage protrudes from the loading bed of the preceding vehicle

·

When the preceding vehicle has an unusual shape (such as a tractor or sidecar)

·

Bicycles for children, bicycles carrying luggage, bicycles with two or more people riding, irregularly shaped bicycles (bicycles with child-seats, tandem bicycles, etc.)*1

·

When the height of a pedestrian or person riding the bicycle is approximately 1.0 m (3.2 ft.) or less or 2 meters (6.5 ft.) or more*1

·

When the outline of a pedestrian's body or person riding the bicycle is ambiguous (such as when wearing a raincoat or long skirt)*1

·

When a pedestrian or person riding a bicycle is stooping or squatting*1

·

When a pedestrian or person riding a bicycle is moving quickly*1

·

When a pedestrian is pushing a baby stroller, wheelchair or bicycle, etc.*1

·

During bad weather (such as rain, fog, snow or dust storm)

·

When there is steam, smoke, etc. in front of the vehicle

·

When the operation target blends in with the background when the background is dim (dawn or dusk) or when it is dark (during night hours or when traveling in a tunnel, etc.)

·

When driving in a location with sudden changes in the surrounding brightness (such as the entrance or exit of a tunnel)

·

For a short time after starting the hybrid system and starting to drive*2

·

For a short time after starting the engine and starting to drive*3

·

When turning left or right or for several seconds after turning left or right

·

While driving on a curve or for several seconds after turning on a curve

·

When own vehicle is sliding sideways

·

If the front of the vehicle is raised or lowered [Case 4]

·

When the wheels are not correctly aligned

·

When the wiper blade obstructs the view of the forward recognition camera

·

While driving at excessively high speed

·

When driving on a slope

·

When the angle of the millimeter wave radar sensor assembly or forward recognition camera is misaligned



[Case 1]
Y186322

[Case 2]
Y186305

[Case 3]
Y186321

[Case 4]
Y192590


ii.

In some situations such as the following, sufficient braking force may not be obtained, preventing the system from performing properly:

·

If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet

·

If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.)

·

When the vehicle is being driven on a gravel road or other slippery surface





h.

To avoid malfunction of the millimeter wave radar sensor assembly

i.

Observe the following precautions. Otherwise, the millimeter wave radar sensor assembly may not operate properly, possibly leading to an accident resulting in death or serious injury.

·

Keep the millimeter wave radar sensor assembly and grille cover clean at all times. If the front of the millimeter wave radar sensor assembly or the front or back of the grille cover is dirty or covered with water droplets, snow, etc., clean it.

Y241592C01
0.719,1.938 1.385,1.938 true 1.917,1.917 2.833,1.917 true 0.552,1.854 0.979,2.188 0.427,0.333 10 false *1 2.865,1.833 3.292,2.167 0.427,0.333 10 false *2
*1 Grille Cover *2 Millimeter Wave Radar Sensor Assembly


·

Clean the millimeter wave radar sensor assembly and grille cover with a soft cloth so you do not mark or damage them.

·

Do not attach accessories, stickers (including transparent stickers) or other items to the millimeter wave radar sensor assembly, grille cover or surrounding area.

·

Do not subject the millimeter wave radar sensor assembly or its surrounding area to a strong impact.

·

Do not disassemble the millimeter wave radar sensor assembly.

·

Do not modify or paint the millimeter wave radar sensor assembly, grille cover or surrounding area.

·

The millimeter wave radar sensor assembly complies with relevant radio wave regulations, as shown by the label attached to the millimeter wave radar sensor assembly. Do not remove the label. Additionally, disassembly or modification of the millimeter wave radar sensor assembly may be prohibited by law.

·

Do not erase the letters printed on the millimeter wave radar sensor assembly.

·

Use a dedicated grille cover for the millimeter wave radar sensor assembly.




i.

To avoid malfunction of the forward recognition camera

i.

Observe the following precautions. Otherwise, the forward recognition camera may not operate properly, possibly leading to an accident resulting in death or serious injury.

·

Keep the windshield clean at all times. If the windshield is dirty or covered with an oily film, water droplets, snow, etc., clear the windshield.

·

If a glass coating agent is applied to the windshield, it will still be necessary to use the windshield wipers to remove water droplets from the area of the windshield in front of forward recognition camera.

·

Do not install antennas or attach stickers (including transparent stickers) or other items in front of the windshield forward recognition camera.

Y241593

·

If the part of the windshield in front of the forward recognition camera is fogged up or covered with condensation or ice, use the windshield defogger to remove the fog, condensation or ice.

·

If water droplets cannot be properly removed from the area of the windshield in front of the forward recognition camera by the windshield wipers, replace the wiper blade rubber or wiper blade.

·

Do not attach window tinting to the windshield.

·

Replace the windshield if it is damaged or cracked. If the windshield needs to be replaced, replace it with a regular parts number.

·

Do not get the forward recognition camera wet.

·

Do not allow bright lights to shine into the forward recognition camera.

·

Do not dirty or damage the forward recognition camera. When cleaning the inside of the windshield, do not allow glass cleaner to contact the lens. Also, do not touch the lens.

·

Do not subject the forward recognition camera to a strong impact.

·

Do not change the installation position or direction of the forward recognition camera or remove it.

·

Do not disassemble the forward recognition camera.

·

Do not install an electronic device or device that emits strong electric waves near the forward recognition camera.

·

Do not modify any components of the vehicle around the forward recognition camera (inner rear view mirror assembly, visor assembly, etc.) or ceiling.

·

Do not attach any accessories that may obstruct the forward recognition camera to the hood, front grille or front bumper.

·

If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the forward recognition camera.

·

Do not modify the headlights or other lights.




j.

If the PCS warning light illuminates and a warning message is displayed on the multi-information display

i.

The pre-collision system may be temporarily unavailable or there may be a malfunction in the system.


ii.

In the following situations, the warning light will turn off, the message will disappear and the system will become operational when normal operating conditions return:

·

When the millimeter wave radar sensor assembly or forward recognition camera or the area around either sensor is hot, such as in the sun

·

When the millimeter wave radar sensor assembly or forward recognition camera or the area around either sensor is cold, such as in an extremely cold environment

·

When the millimeter wave radar sensor assembly and forward recognition camera is unable to detect the surrounding condition due to being in a dark location, reflections, snow or fog, etc., or when driving in an area with not detection objects.

·

When the part of the windshield in front of the forward recognition camera is fogged up or covered with condensation or ice

·

When the millimeter wave radar sensor assembly or grille cover is dirty or covered with snow, etc.

·

If the forward recognition camera is obstructed, such as when the hood is open or a sticker is attached to the windshield near the forward recognition camera



HINT:

If the PCS warning light continues to illuminate or the warning message does not disappear, the system may be malfunctioning.




k.

When VSC is Stopped

i.

When the VSC operation is stopped by turning the VSC switch off, the pre-collision brake assist operation and pre-collision braking is also stopped. (Pre-collision warning continues to operate)


ii.

When the VSC operation is stopped, the VSC OFF indicator light and PCS warning light turn on and a message is displayed on the multi-information display.