Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE › 2018.10–2020.08
NM3620E _59 Vehicle Exterior _077728 EXTERIOR PANELS / TRIM _0377329 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  SAFETY FEATURES  


FUNCTION


a.

Impact Absorbing Structure for Frontal Collision

i.

In order to ensure passenger protection performance during frontal collisions, a vehicle structure that optimally absorbs and disperses the impact load has been developed.

·

Impact load from the upper member (*1 in illustration) is dissipated to the roof rail (*3 in illustration) through the front body pillar (*2 in illustration) during frontal collisions (*A in illustration).

·

Impact load from the side member (*4 in illustration) is dispersed to the rocker (*6 in illustration) through the dash cross member (*5 in illustration) during frontal collisions (*A in illustration).

·

Impact load from the front bumper reinforcement (*7 in illustration) is dispersed to the suspension member (*8 in illustration) through the No. 2 member (*9 in illustration) during frontal collisions (*A in illustration).

·

Impact from the side member (*4 in illustration) is efficiently dispersed to the rocker (*6 in illustration), kick upper (*10 in illustration) and tunnel parts (*11 in illustration) through the dash cross member (*5 in illustration) during offset collisions (*B in illustration).

Impact Absorbing Structure for Frontal Collision (The illustration is an example only.)
V123228C01
0.958,4.396 1.115,4.396 1.115,4.396 1.354,3.74 true 0.917,1.75 1.083,1.75 1.083,1.75 1.583,2.25 true 1.667,1.167 1.833,1.167 1.833,1.167 2.333,1.667 true 2.583,0.583 2.75,0.583 2.75,0.583 3.25,1.083 true 3.958,4.552 3.792,4.552 3.792,4.552 3.167,3.604 true 4.458,4.208 4.292,4.208 4.292,4.208 3.958,3.625 true 3.063,5.021 2.896,5.021 2.896,5.021 2.385,3.938 true 3.188,4.438 3.021,4.438 3.021,4.438 2.531,3.49 true 2.115,4.396 1.948,4.396 1.948,4.396 1.802,4.031 true 1.583,8.5 1.75,8.5 1.75,8.5 2.031,7.594 true 2.417,8.5 2.583,8.5 2.583,8.5 2.844,7.5 true 3.563,8.531 3.396,8.531 3.396,8.531 3.229,8.031 true 4.26,5.063 4.094,5.063 4.094,5.063 3.771,6.802 true 4.406,8.521 4.271,8.521 4.271,8.521 3.479,7.542 true 0.708,0.427 1,0.625 0.292,0.198 12 false *A: 0.729,5.219 1.021,5.427 0.292,0.208 12 false *B: 0.74,1.667 1.052,1.865 0.313,0.198 10 false *1 1.51,1.083 1.823,1.24 0.313,0.156 10 false *2 2.417,0.49 2.729,0.646 0.313,0.156 10 false *3 3.24,4.365 3.552,4.521 0.313,0.156 10 false *4 2.26,8.417 2.573,8.573 0.313,0.156 10 false *5 3.604,8.458 3.917,8.615 0.313,0.156 10 false *6 0.802,4.323 1.125,4.542 0.323,0.219 10 false *7 3.104,4.948 3.458,5.177 0.354,0.229 10 false *8 2.156,4.333 2.469,4.49 0.313,0.156 10 false *9 4.417,8.438 4.729,8.677 0.313,0.24 10 false *10 4.302,4.979 4.615,5.135 0.313,0.156 10 false *11 4,4.469 4.313,4.625 0.313,0.156 10 false *5 4.5,4.135 4.813,4.292 0.313,0.156 10 false *6 1.417,8.417 1.729,8.573 0.313,0.156 10 false *4
*A Frontal Collision (Full-lap) *B Frontal Collision (Offset)
*1 Upper Member *2 Front Body Pillar
*3 Roof Rail *4 Side Member
*5 Dash Cross Member *6 Rocker
*7 Front Bumper Reinforcement *8 Suspension Member
*9 No. 2 Member *10 Kick Upper
*11 Tunnel Parts - -
V100136

Front Impact Energy
V100135

Dissipate




ii.

A widened structure is used for the side member. As a result, high collision safety is ensured for various types of collisions.

Side Member (The illustration is an example only.)
V123225C01
2.01,0.667 2.167,0.667 2.167,0.667 2.594,1.083 true 1.917,4.25 2.073,4.25 2.073,4.25 2.5,3.75 true 1.667,1.917 1.823,1.917 1.823,1.917 2.208,2.302 true 1.844,0.583 2.156,0.781 0.313,0.198 10 false *1 1.5,1.833 1.813,2.031 0.313,0.198 10 false *2 1.75,4.167 2.063,4.365 0.313,0.198 10 false *3 3.052,2.156 3.365,2.354 0.313,0.198 10 false *a
*1 Front Side Member RH *2 Front Bumper Reinforcement
*3 Front Side Member LH - -
*a Wider - -



iii.

A No. 2 member is provided under the front bumper reinforcement and side member. As a result, the amount of impact load absorbed during the initial stage of the collision is increased, improving collision energy absorption efficiency.

No. 2 Member (This illustration is an example only.)
V123226C01
4.333,2.25 5.583,1.583 5.583,1.583 5.75,1.583 true 1.167,3.333 1.333,3.333 1.333,3.333 1.833,3 true 1.167,2 1.333,2 1.333,2 1.833,2.25 true 1,1.938 1.313,2.135 0.313,0.198 10 false *1 5.771,1.521 6.083,1.719 0.313,0.198 10 false *3 1,3.271 1.313,3.469 0.313,0.198 10 false *2
*1 Front Bumper Reinforcement *2 No. 2 Member
*3 Front Side Member LH - -




b.

Roof Crush Resistance

i.

Hot-stamped steel (tensile strength: 1500 MPa class), ultra high-tensile strength steel (tensile strength: 1180 MPa and 980 MPa class) and high-tensile strength steel (tensile strength: 780 MPa and 590 MPa class) are used in the body frame, achieving weight reduction and structure simplification while ensuring strength.


ii.

Impact load from the top of the vehicle is supported by the front body pillar (*1 in illustration), center body pillar (*2 in illustration), front header (*3 in illustration), roof center reinforcement (*4 in illustration) and rail outer (*5 in illustration), suppressing cabin deformation.


iii.

The wall of the center body pillar inner (*6 in illustration) wraps around the upper part of the rocker (*7 in illustration). As a result, collapsing of the rail is suppressed when impact load is applied to it from the top of the vehicle.

Impact Absorbing Structure for Above Collision (The illustration shown is an example only.)
V123232C01
4.708,3.896 4.823,3.896 4.823,3.896 5.302,4.427 true 1.156,0.677 1.323,0.677 1.323,0.677 2.406,1.594 true 1.917,0.292 2.083,0.292 2.083,0.292 3.167,1.208 true 0.698,1.604 0.865,1.604 0.865,1.604 2.26,2.563 true 3.646,2.438 6.104,1.26 6.104,1.26 6.25,1.26 true 4.292,1.49 6.042,0.656 6.042,0.656 6.208,0.656 true 5.052,5.104 4.792,4.49 4.792,4.49 4.667,4.49 true 1.76,0.219 2.073,0.417 0.313,0.198 10 false *4 0.99,0.604 1.302,0.802 0.313,0.198 10 false *3 0.5,1.552 0.813,1.75 0.313,0.198 10 false *1 6.24,0.594 6.552,0.792 0.313,0.198 10 false *5 6.292,1.198 6.604,1.396 0.313,0.198 10 false *2 4.49,3.823 4.802,4.021 0.313,0.198 10 false *6 4.49,4.427 4.802,4.625 0.313,0.198 10 false *7
*1 Front Body Pillar (Tensile Strength: 1500 MPa Class) *2 Center Body Pillar (Tensile Strength: 1500 MPa Class)
*3 Front Header (Tensile Strength: 980 MPa Class) *4 Roof Center Reinforcement (Tensile Strength: 1180 MPa Class)
*5 Rail Outer (Tensile Strength: 1180 and 590 MPa Class) *6 No. 4 Inner Pillar Sub-assembly LH (Tensile Strength: 590 MPa Class)
*7 Floor Side Member Inner LH (Tensile Strength: 1180 MPa Class) - -
V100136

Above Impact Energy
V100135

Dissipate



iv.

The roof side rail upper (*1 in illustration) and roof side rail outer No. 2 (*2 in illustration) are positioned so that they extend to the front of the quarter body pillar. As a result, collapsing of the rail is suppressed when impact load is applied to it from the top of the vehicle.

Roof Side Rail (This illustration is an example only.)
V123233C01
3.125,1.729 3.438,1.167 3.438,1.167 3.563,1.167 true 4.51,1.729 4.823,1.167 4.823,1.167 4.948,1.167 true 3.635,1.083 4.156,1.292 0.521,0.208 10 false *1 (*a) 5,1.094 5.396,1.302 0.396,0.208 10 false *2 (*b)
*1 Roof Side Rail Upper LH *2 Roof Side Rail Outer No. 2 LH
*a Ultra High-tensile Strength Steel (Tensile Strength: 1180 MPa Class) *b High-tensile Strength Steel (Tensile Strength: 590 MPa Class)




c.

Impact Absorbing Structure for Side Collision

i.

Hot-stamped steel (tensile strength: 1500 MPa class), ultra high-tensile strength steel (tensile strength: 1180 MPa and 980 MPa class) and high-tensile strength steel (tensile strength: 780 MPa and 590 MPa and 440 MPa class) are used in the body frame, achieving weight reduction and structure simplification while ensuring strength.

·

Hot-stamped sheet steel, ultra high strength sheet steel and high strength sheet steel is used for the body frameworks, increasing strength and suppressing cabin deformation.

·

Impact load from the center body pillar (*1 in illustration) is dispersed to the rocker (*3 in illustration) through the center body pillar reinforcement lower (*2 in illustration) during side collisions.

·

Impact load from the center body pillar (*1 in illustration) is dispersed to the roof center reinforcement (*4 in illustration) through the rail outer (*5 in illustration) during side collisions.

·

Impact load from the center body pillar (*1 in illustration) is dispersed to the front header (*6 in illustration) and cowl top panel (*7 in illustration) through the front body pillar (*8 in illustration) during side collisions.

·

A high strength and thick front door impact beam (*9 in illustration) with a large diameter is used, suppressing inwards intrusion during collisions with another vehicle.

Side Collision (This illustration is an example only.)
V123229C01
2.25,1.417 2.417,1.417 2.417,1.417 3.25,2.167 true 3.167,1.083 3.333,1.083 3.333,1.083 4.167,1.833 true 1.167,2.167 1.333,2.167 1.333,2.167 2.583,3.167 true 4.49,2.948 5.917,4.083 5.917,4.083 6.083,4.083 true 4.958,2.021 5.667,1 5.667,1 5.833,1 true 3.26,3 1.833,1.75 1.833,1.75 1.667,1.75 true 3.563,4.198 3.833,4.75 3.833,4.75 4,4.75 true 2.667,5.167 2.833,5.167 2.833,5.167 3.417,3.833 true 5.083,4.75 4.927,4.75 4.927,4.75 4.344,3.875 true 1,2.104 1.313,2.302 0.313,0.198 10 false *7 1.5,1.667 1.813,1.865 0.313,0.198 10 false *8 2.083,1.344 2.396,1.542 0.313,0.198 10 false *6 3.01,1.021 3.323,1.219 0.313,0.198 10 false *4 5.896,0.938 6.208,1.135 0.313,0.198 10 false *5 6.115,4.021 6.427,4.219 0.313,0.198 10 false *1 4.031,4.698 4.344,4.896 0.313,0.198 10 false *3 5.115,4.688 5.427,4.885 0.313,0.198 10 false *2 2.51,5.094 2.823,5.292 0.313,0.198 10 false *9
*1 Center Body Pillar (Tensile Strength: 1500 MPa Class) *2 Center Body Pillar Reinforcement Lower (Tensile Strength: 440 MPa Class)
*3 Rocker (Tensile Strength: 1180 MPa Class) *4 Roof Center Reinforcement (Tensile Strength: 1180 MPa Class)
*5 Rail Outer (Tensile Strength: 1180 and 590 MPa Class) *6 Front Header (Tensile Strength: 980 MPa Class)
*7 Cowl Top Panel *8 Front Body Pillar (Tensile Strength: 1500 MPa Class)
*9 Front Door Impact Beam - -
V100136

Side Impact Energy
V100135

Dissipate




ii.

Diagonal reinforcements are used for the rear door. As a result, door deformation is suppressed during collisions, helping ensure that the doors can be opened.

Diagonal Reinforcement (The illustration is an example only.)
V123231C01
4.333,2.115 5.021,1.615 5.021,1.615 5.177,1.615 true 5.219,1.552 5.531,1.75 0.313,0.198 10 false *1
*1 Rear Door Rear Upper Frame Reinforcement LH - -



iii.

Bulkheads are used inside the rocker to create a structure that efficiently transmits impact load to the floor cross reinforcement during side collisions.

V123230C01
3.615,2.417 5.135,2.458 5.135,2.458 4.073,2.208 true 5.188,2.385 5.5,2.583 0.313,0.198 10 false *1
*1 Rocker Panel Reinforcement No. 4 LH - -
V100135

Dissipate
V100136

Side Impact Energy



iv.

For the normal roof specification, the ultra high strength sheet steel (tensile strength: 1180 MPa class) roof center reinforcement (*1 in illustration) and roof rail (*2 in illustration) are connected by spot welds to create a structure that transmits and disperses impact load from the center body pillar to the roof during collisions.

Normal Roof (This illustration is an example only.)
V123234C01
2.51,1.042 3.104,0.26 3.104,0.26 3.24,0.26 true 4.271,1.76 5.344,0.302 5.344,0.302 5.479,0.302 true 3.26,0.198 3.573,0.396 0.313,0.198 10 false *1 5.542,0.229 5.854,0.427 0.313,0.198 10 false *2
*1 Roof Center Reinforcement *2 Roof Rail
V100135

Dissipate - -



v.

For the sliding roof specification, the sliding roof unit reinforcement (*1 in illustration) and roof rail (*2 in illustration) are connected through the curtain shield airbag inflator bracket (*3 in illustration). As a result, a structure is created that efficiently transmits and disperses impact load from the center body pillar to the roof during collisions.

Sliding Roof (This illustration is an example only.)
V123235C01
1.854,1.073 2.385,0.354 2.385,0.354 2.542,0.354 true 2.969,1.854 4.083,0.344 4.083,0.344 4.24,0.344 true 5.083,1.229 5.604,0.375 5.604,0.375 5.76,0.375 true 4.833,2.635 5.49,2.885 5.49,2.885 5.646,2.885 true 2.583,0.292 2.885,0.458 0.302,0.167 10 false *1 4.281,0.292 4.594,0.448 0.313,0.156 10 false *2 5.802,0.313 6.313,0.469 0.51,0.156 10 false *3 5.698,2.823 6.208,2.979 0.51,0.156 10 false *4
*A Destination package for Korea - -
*1 Roof Center Reinforcement *2 Roof Rail
*3 Curtain Shield Airbag Inflator Bracket - -
V100135

Dissipate - -




d.

Impact Absorbing Structure for Rear Collision

i.

A light and high strength rear bumper reinforcement sub-assembly is used. It uses ultra high strength sheet steel.

Rear Bumper Reinforcement (This illustration is an example only.)
V123236C01
4.344,6.573 4.563,7.063 4.563,7.063 4.698,7.063 true 4.375,3.01 4.583,3.5 4.583,3.5 4.719,3.5 true 1.583,4.479 7.156,5.01 5.573,0.531 12 false *B: 1.583,0.927 7.156,1.448 5.573,0.521 12 false *A: 4.76,6.979 7.156,7.323 2.396,0.344 10 false *1 (*a) 4.76,3.417 7.156,3.76 2.396,0.344 10 false *1 (*a)
*A Models for Europe *B Except models for Europe
*1 Rear Bumper Reinforcement - -
*a Ultra High-tensile Strength Steel (Tensile Strength: 980 MPa Class) - -



ii.

A rear bumper reinforcement that uses ultra high strength sheet steel is provided to achieve high support strength when an impact is received from the rear.


iii.

A high strength rear bumper reinforcement is used to disperse impact energy to the opposite side of the vehicle during rear collisions, suppressing cabin deformation.

Impact Absorbing Structure for Rear Collision (This illustration is an example only.)
V123237C01
1.813,3.125 1.938,3.125 1.938,3.125 2.521,2.396 true 0.854,1.5 1.021,1.5 1.021,1.5 1.802,1.948 true 4.719,2.99 5.896,3.552 5.896,3.552 6.021,3.552 true 2.563,4.563 3,4.833 3,4.833 3.167,4.833 true 2.5,4.969 3,5.25 3,5.25 3.167,5.25 true 5.896,4.979 6.167,5.25 6.167,5.25 6.333,5.25 true 0.677,1.406 0.99,1.563 0.313,0.156 10 false *1 1.646,3.063 1.958,3.219 0.313,0.156 10 false *2 6.073,3.469 6.385,3.625 0.313,0.156 10 false *3 3.594,3.198 3.719,3.375 0.125,0.177 10 false A 3.24,4.729 3.552,4.885 0.313,0.156 10 false *4 6.417,5.167 6.729,5.323 0.313,0.156 10 false *5 2.792,3.688 2.917,3.865 0.125,0.177 10 true A 3.365,2.813 3.49,2.99 0.125,0.177 10 false B 2.594,3.156 2.719,3.333 0.125,0.177 10 false B 1.813,5.427 2.125,5.583 0.313,0.156 10 false *a 5.281,5.427 5.594,5.583 0.313,0.156 10 false *b 3.25,5.177 3.563,5.333 0.313,0.156 10 false *2
*1 Rear Bumper Reinforcement *2 Rear Floor Side Member RH
*3 Rear Floor Cross Member Center *4 Rear Rocker Reinforcement RH
*5 Rear Floor Side Member Reinforcement - -
*a A - A Cross Section *b B - B Cross Section
V100136

Rear Impact Energy
V100135

Dissipate




e.

Reduction of Pedestrian Leg Injury

i.

A front bumper energy absorber No. 2 is provided in front of the front bumper reinforcement and a front bumper absorber lower is provided at the lower part of the front bumper reinforcement No. 2*1 or radiator support*2, creating a structure that reduces the impact to the legs of a pedestrian during collisions.

HINT:

*1: HV models

*2: Gasoline models


Pedestrian Leg Injury Reduction (This illustration is an example only.)
V123241C01
4.51,0.146 7.031,4.667 2.521,4.521 0.938,4.438 1.063,4.438 1.063,4.438 1.365,3.438 true 5.24,1.552 5.5,1.135 5.5,1.135 5.656,1.135 true 1.885,4.469 1.75,4.469 1.75,4.469 1.5,3.781 true 5.01,3.656 6.021,2.917 6.021,2.917 6.146,2.917 true 5.844,1.833 6.104,1.417 6.104,1.417 6.26,1.417 true 5.677,3.667 6.177,3.333 6.177,3.333 6.323,3.333 true 0.875,2.708 1.031,2.906 0.156,0.198 10 false A 0.854,3.583 1.01,3.781 0.156,0.198 10 false A 5.667,4.365 5.823,4.563 0.156,0.198 10 false *a 0.76,4.365 0.917,4.563 0.156,0.198 10 false *1 1.917,4.396 2.073,4.594 0.156,0.198 10 false *2 5.719,1.042 5.875,1.24 0.156,0.198 10 false *1 6.188,2.854 6.344,3.052 0.156,0.198 10 false *2 6.292,1.354 6.448,1.552 0.156,0.198 10 false *3 6.365,3.24 6.521,3.438 0.156,0.198 10 false *4
*1 Front Bumper Energy Absorber No. 2 *2 Front Bumper Absorber Lower
*3 Front Bumper Reinforcement *4 Front Bumper Reinforcement No. 2
*a A - A Cross Section - -




f.

Reduction of Pedestrian Head Injury

i.

A deformation stroke is ensured for the front part of the engine hood to absorb impact during collisions, creating a structure that reduces the impact to the head of a pedestrian during collisions.

Hood Sub-assembly (This illustration is an example only.)
V123238C01
2.24,2.104 2.917,1.167 2.917,1.167 3.042,1.167 true 4.594,2.385 4.333,1.958 true 6.385,3.417 6.323,2.469 true 5.51,3.583 5.375,3.583 5.375,3.583 5.24,3.177 true 5.302,1.479 5.469,1.083 5.469,1.083 5.604,1.083 true 6.01,1.969 6.167,1.26 6.167,1.26 6.281,1.26 true 4.313,2.615 4.063,2.25 true 6.729,3.01 6.5,2.167 true 4.167,3.469 4.313,3.469 4.313,3.469 5.24,2.438 true 3.104,1.104 3.417,1.26 0.313,0.156 10 false *1 4.104,1.75 4.573,1.927 0.469,0.177 10 false *2 (*b) 6.573,3.052 7.021,3.229 0.448,0.177 10 false *4 (*b) 5.656,1.01 6.115,1.177 0.458,0.167 10 false *5 (*b) 5.24,4 5.552,4.156 0.313,0.156 10 false *a 1.573,2.25 1.688,2.406 0.115,0.156 10 true A 1.198,3.021 1.313,3.177 0.115,0.156 10 true A 3.74,2.021 4.302,2.208 0.563,0.188 10 false *2 (*c) 6.344,1.177 6.792,1.333 0.448,0.156 10 false *5 (*c) 5.552,3.521 5.865,3.677 0.313,0.156 10 false *3 6.208,3.479 6.656,3.656 0.448,0.177 10 false *4 (*c) 4,3.385 4.313,3.542 0.313,0.156 10 false *d
*1 Hood Sub-assembly *2 Hood Panel
*3 Hood Lock Hook *4 Hood Panel Reinforcement
*5 Headform Impactor - -
*a A - A Cross Section *b Before Collision
*c After Collision *d Stroke



ii.

A collision absorption structure is used for the front fender extension and apron fender side extension, creating a structure that reduces the impact to the head of a pedestrian during collisions where the pedestrian contacts the fender.

Front Fender (This illustration is an example only.)
V123239C01
0.573,3.542 0.729,3.542 0.729,3.542 1.573,2.052 true 1.365,3.542 1.531,3.542 1.531,3.542 2.115,2.167 true 5.75,1.417 5.333,0.917 5.333,0.917 5.135,0.917 true 4.917,1.833 4.698,1.333 4.698,1.333 4.5,1.333 true 1.917,4.333 2.083,4.333 2.083,4.333 3,5.25 true 1.917,4.917 2.083,4.917 2.083,4.917 2.667,5.5 true 4.25,5.417 5.083,5.583 true 4.542,5.656 5.125,6.156 true 3.5,4.333 3.906,3.917 3.906,3.917 4.073,3.917 true 4.25,4.75 4.594,4.375 4.594,4.375 4.74,4.375 true 2.083,2.594 2.438,3.521 2.438,3.521 2.573,3.521 true 5.198,5.5 5.677,5.667 0.479,0.167 10 false *1 (*b) 1.198,3.469 1.51,3.625 0.313,0.156 10 false *2 4.938,0.844 5.25,1 0.313,0.156 10 false *1 4.333,1.26 4.646,1.417 0.313,0.156 10 false *2 3.531,6.354 3.844,6.51 0.313,0.156 10 false *a 1.5,4.25 1.958,4.427 0.458,0.177 10 false *3 (*b) 1.51,4.844 2.052,5.021 0.542,0.177 10 false *3 (*c) 4.125,3.865 4.646,4.063 0.521,0.198 10 false *4 (*b) 0.417,3.469 0.729,3.625 0.313,0.156 10 false *1 5.302,1.708 5.615,1.865 0.313,0.156 10 false A 6.156,1.292 6.469,1.448 0.313,0.156 10 false A 5.198,6.125 5.688,6.292 0.49,0.167 10 false *1 (*c) 4.781,4.302 5.302,4.5 0.521,0.198 10 false *4 (*b) 2.625,3.448 3.083,3.625 0.458,0.177 10 false *3
*1 Front Fender Extension Top RH *2 Apron Fender Side Extension RH
*3 Front Fender Panel RH *4 Headform Impactor
*a A - A Cross Section *b Before Collision
*c After Collision - -



iii.

A collision absorption structure is used for the cowl top ventilator louver sub-assembly.

·

During a collision with a pedestrian, the cowl top ventilator louver sub-assembly (*1 in illustration) collapse similar to a pantograph in order to absorb impact load. (*a in illustration)

·

When the pedestrian contacts the vehicle, the wiper pivot detaches to ensure the stroke space in consideration of reducing the extent of the pedestrian's injuries. (*b in illustration)


Cowl Top Ventilator Louver (This illustration is an example only.)
V123240C01
1.615,1.104 1.302,0.74 1.302,0.74 1.156,0.74 true 1.49,3.885 1.854,3.5 1.854,3.5 1.958,3.5 true 1.698,4.479 2.24,3.885 2.24,3.885 2.375,3.885 true 5.458,5.01 6.052,3.938 6.052,3.938 6.208,3.938 true 4.479,6.313 4.635,6.313 4.635,6.313 5.24,5.385 true 3.323,6.24 3.177,6.24 3.177,6.24 1.885,5.448 true 2.448,4.354 2.302,4.354 2.302,4.354 1.698,5.031 true 2.688,6.5 2.552,6.5 2.552,6.5 1.833,5.542 true 0.969,0.646 1.281,0.802 0.313,0.156 10 false *1 6.271,3.865 6.583,4.021 0.313,0.156 10 false *2 1.625,6.427 1.938,6.583 0.313,0.156 10 false *a 5.427,6.469 5.917,6.76 0.49,0.292 10 false *b 5.323,0.958 5.448,1.125 0.125,0.167 10 false A 4.563,2.417 4.688,2.583 0.125,0.167 10 true A 5.333,2.729 5.458,2.896 0.125,0.167 10 true B 6.052,1.323 6.177,1.49 0.125,0.167 10 true B 1.99,3.427 2.479,3.604 0.49,0.177 10 false *3 (*c) 2.406,3.802 2.896,3.979 0.49,0.177 10 false *3 (*d) 2.531,4.281 3.063,4.49 0.531,0.208 10 false *1 (*c) 3.375,6.156 3.906,6.365 0.531,0.208 10 false *1 (*d) 2.74,6.427 3.229,6.719 0.49,0.292 10 false *e 4.323,6.229 4.813,6.521 0.49,0.292 10 false *f
*1 Cowl Top Ventilator Louver Sub-assembly *2 Wiper Pivot
*3 Headform Impactor - -
*a A - A Cross Section *b B - B Cross Section
*c Before Collision *d After Collision
*e Pantograph Structure *f Stroke