FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*: Models with paddle shift switch (transmission shift switch assembly) |
||
| Linear Solenoid Valve SLS | Controls the oil pressure of the secondary pulley in accordance with the input shaft torque to control belt clamping force. | |
| Linear Solenoid Valve SLP | Controls the oil pressure of the primary pulley in accordance with the vehicle speed and accelerator pedal position signals to control the speed ratio. | |
| Linear Solenoid Valve SLU | Performs lock-up clutch control. | |
| Linear Solenoid Valve SL1 | Controls the C1 clutch for gear mode. | |
| Linear Solenoid Valve SL2 | Controls the C2 clutch for belt mode. | |
| Linear Solenoid Valve SLG | Controls the synchronizer mechanism and B1 brake (reverse). | |
| Transmission Revolution Sensor (NC1) | Detects the No. 1 drive gear speed. | |
| Transmission Revolution Sensor (NT) | Detects the primary pulley speed. | |
| Transmission Revolution Sensor (NSS) | Detects the secondary pulley speed. | |
| Transmission Revolution Sensor (NOUT) | Detects the output speed. | |
| CVT Fluid Temperature Sensor (Transmission Wire) | Detects the CVT fluid temperature. | |
| Oil Pressure Sensor | Detects the steel belt clamping force. | |
| Clutch Stroke Sensor | Detects the shift fork position. | |
| Engine Coolant Temperature Sensor | Detects the engine coolant temperature. | |
| Throttle Body with Motor Assembly | Throttle Position Sensor | Detects the opening angle of the throttle valve. |
| Mass Air Flow Meter Sub-assembly | Intake Air Temperature Sensor | Detects the intake air volume and intake air temperature. |
| Airbag ECU (Airbag Sensor Assembly) | Yawrate Sensor | Detects the vehicle's yaw rate. |
| Acceleration Sensor | Detects the vehicle's longitudinal and lateral acceleration and deceleration. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Park/Neutral Position Switch Assembly | Detects the shift lever position. | |
| Transmission Floor Shift Assembly | Transmission Control Switch | ·
Detects when the shift lever is in M. ·
Detects the driver's shift-up and shift-down operations when the shift lever is in M. |
| Paddle Shift Switch (Transmission Shift Switch Assembly)* | ·
Detects the driver's shift-up and shift-down operations in 10-speed sport sequential shiftmatic mode. ·
Operating this switch when the shift lever is in D changes the mode temporarily to 10-speed sport sequential shiftmatic mode. |
|
| Crank Position Sensor | Detects the engine speed. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal opening angle. | |
| Air Conditioning Amplifier Assembly | Transmits the operating state of the air conditioning system. | |
| Transmission Control ECU | Drives each solenoid valve based on signals from each sensor and switch and optimally controls the CVT. | |
| Combination Meter Assembly | Multi-information Display | ·
Displays the shift lever position. ·
Displays the shift range. ·
Displays the drive mode. |
| MIL | Illuminates to inform the driver when the transmission control ECU detects a malfunction. | |
| Buzzer | Sounds when shift-down operation is rejected in 10-speed sport sequential shiftmatic mode. | |
| Brake Actuator Assembly | Skid Control ECU | Sends the information about the operation conditions of the brake control system to the transmission control ECU. |
| Integration Control and Panel Assembly | Drive Mode Select | Selects the drive mode (ECO, NORMAL, SPORT). |
| SNOW Mode Switch | Switches to the SNOW mode. | |
SYSTEM CONTROL
| Control | Outline |
|---|---|
|
*: Models with paddle shift switch (transmission shift switch assembly) |
|
| Engine-CVT Integrated Control | Performs coordinate control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy. |
| Automatic Shift Control (Speed Ratio Control) | Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals. |
| Acceleration Improvement Control | Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input. |
| Deceleration Improvement Control | Determines a pulley ratio which allows for high engine speed to be maintained during deceleration, ensuring adequate engine braking. |
| SPORT Mode Control | SPORT Mode Control provides excellent response and linear and powerful acceleration by changing Engine and CVT control to exclusive control tuning. |
| 10-speed Sport Sequential Shiftmatic | Enables driving in a specific shift range which is selected using the shift lever or paddle shift switch (transmission shift switch assembly)*, providing engine braking force appropriate to each shift range. |
| Uphill/Downhill Shift Control | Uses the transmission control ECU to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by restricting downshifts. |
| Flex Lock-up Control | By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy. |
| Clutch Capacity Control | When driving in belt mode, and sudden braking causes excessive input forces from the road surface, the C2 clutch performs torque capacity control to protect the belt by limiting the load applied to it. |
| Engine stall avoidance control | If the engine stalls 3 times or more, the TCM suspects that the linear solenoid valve SLU is stuck on. In this case, the TCM forcibly releases the lock-up oil pressure when the engine is next started as engine stall avoidance control. If the shift lever is moved to D or R during engine stall avoidance control, shift shock will occur. In this case, the gear ratio range and output torque will be restricted. |
Engine - CVT Integrated Control
To perform fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.
Automatic Shift Control (Speed Ratio Control)
The transmission control ECU determines the driving conditions through each input signal and selects the optimal control to achieve output which meets the driver's intentions.
When the shift lever is in D, the system performs engine integrated control to optimize fuel economy characteristics and driving performance.
When the shift lever is in M, if the vehicle reaches the set speed when accelerating, the system automatically upshifts.
Acceleration Improvement Control (Gentle acceleration: Low accelerator opening angle range)
While proactively using the high efficiency range to improve fuel economy performance, it is possible to accelerate with smooth shifting that prevents the occupants from feeling the series of operations that include switching from gear mode to belt mode (clutch to clutch), lock-up engagement, and synchronizer engagement.
Acceleration Improvement Control (Intermediate to high accelerator opening angle)
In pursuit of an acceleration feeling that more closely matches the sensibilities of the driver, CVT control has been revised and engine-integrated control has been further evolved.
When starting off, gear mode provides acceleration matched with a linear increase in engine RPM. Even after changeover from gear mode to belt mode, the vehicle speed increase is accompanied by a similar linear engine RPM increase and rhythmical shifting.
Also, while driving, the vehicle speed and changes in the accelerator opening angle are used to determine the driver's desired acceleration, allowing the driver's initial accelerator pedal movements to receive the desired response. Subsequently, optimized shifting speeds enable natural RPM increase to achieve a linear acceleration feel.
Deceleration Improvement Control
During deceleration, a pulley ratio which allows high engine speed to be maintained is calculated, ensuring adequate engine braking.
During subsequent acceleration, the engine is controlled to generate driving force quickly.
Furthermore, to prepare for the changeover to gear mode in order to accelerate again after decelerating, it is necessary to re-engage the synchro that is released at high speeds, but sensing the driver's control inputs and the vehicle behavior when driving allows vehicle behavior when re-engaging to be controlled.
SPORT Mode Control
SPORT mode restricts the variable range of the high gear ratio to ensure a more direct feeling, and provides Deceleration Improvement Control and G AI-shift Control to support vehicle stability during cornering and to ensure responsiveness when exiting a corner by holding the optimal gear ratio. In addition, SPORT Mode Control provides excellent response and linear and powerful acceleration when driving on winding roads or situations in which gentle acceleration is required.
Shift Control
The variable range of the low gear ratio is restricted to ensure appropriate engine braking force when decelerating and to enhance engine response when accelerating.
Depending on the accelerator pedal depression amount, the engine can quickly rev to and be maintained in the high speed range, ensuring quick acceleration and responsiveness.
G AI-shift control
G AI-shift control generates an appropriate engine braking force by varying the gear ratio according to the brake pedal depression force.
If a certain amount of lateral G force is detected, G AI-shift control determines that the vehicle is cornering and maintains engine speed by restricting the variable gear range, ensuring excellent throttle control and appropriate driving force.
When SPORT mode is selected, the SPORT mode indicator in the multi-information display illuminates.
When the engine is stopped with SPORT mode on, SPORT mode is turned off.
When the shift lever is in M or temporary sport sequential shiftmatic mode* is selected, the SPORT mode low gear ratio shift schedule and G AI-shift control are not performed.
*: Models with paddle shift switch (transmission shift switch assembly)
10-speed Sport Sequential Shiftmatic
The driver can select the desired shift range by moving the shift lever to "+" (forward) or to "-" (backward) while the shift lever is in M (10-speed sport sequential shiftmatic mode). As a result, the driver is able to change the shift range with a manual-like feel.
A paddle shift switch (transmission shift switch assembly), which enables the driver to perform shift operations while holding the steering wheel, is provided depending on the model.
10-speed sport sequential shiftmatic mode can be selected from normal driving mode by moving the shift lever to M. The driver can change the gear step by selecting it using the shift lever or paddle shift switch (transmission shift switch assembly)*1 and engine braking force is provided in accordance with the selected gear step.*2
*1: Models with paddle shift switch (transmission shift switch assembly)
*2: On models with the paddle shift switch (transmission shift switch assembly), if the paddle shift switch (transmission shift switch assembly) "+ (UP)" or "- (DOWN)" is operated during normal driving mode with the shift lever in D, gear step change operations are temporarily made available.
Through cooperative control with the Electronic Spark Advance (ESA) and Electronic Throttle Control System-intelligent (ETCS-i), in NORMAL mode, the engine torque is finely controlled during shifting to enhance shift response and reduce shift shock, achieving shifting with smooth and sharp response. In SPORT mode, response to shift operation has been further enhanced and acceleration G behavior during shifting has been tuned, achieving pleasant, crisp shifting.
The shift position and shift range indicator is provided in the multi-information display of the combination meter assembly. When the shift lever is in P, R, N or D, the shift position is indicated in the shift position and shift range indicator. When the shift lever is in M, or temporary 10-speed sport sequential shiftmatic mode is selected with the shift lever in D,* "M" or "D" and the selected shift range is displayed in the shift position and shift range indicator.
*: Models with paddle shift switch (transmission shift switch assembly)
In 10-speed sport sequential shiftmatic mode, the transmission automatically upshifts or downshifts under the following conditions:
| Condition | System Control |
|---|---|
| Engine is under-revving. | 1 step downshift |
| Engine is over-revving. | 1 step upshift |
When the vehicle is stopped during 10-speed sport sequential shiftmatic mode, the transmission automatically downshifts to M1.
When there is a system malfunction or abnormality, or when a requested shift operation is judged to be impossible, operation of the 10-speed sport sequential shiftmatic mode is restricted. In this case, the buzzer in the combination meter will sound to alert the driver.
If the vehicle speed or engine speed exceeds or goes below a preset level in response to the driver's downshift operation request, changing the shift range will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.
On models with a paddle shift switch (transmission shift switch assembly), when the shift lever is in D, the driver can momentarily select a desired gear step by operating the paddle shift. Automatic shift control is reverted to under the following conditions.
| Condition | System Control |
|---|---|
| The driver continues to push the paddle shift in the "+" direction longer than a predetermined length of time. | Reverts to automatic shift control |
| The driver depresses the accelerator pedal longer than a predetermined length of time while the CVT remains in the same gear step. | |
| The vehicle has stopped. | |
| The driver has moved the shift lever to M. | Transfers to manual shifting |
Uphill/Downhill Shift Control
Uphill/downhill shift control helps perform optimal shifting while driving on a winding uphill or downhill road.
When the transmission control ECU determines the vehicle is traveling uphill, the control restricts upshifting, offering smooth driving.
If a signal indicating that the driver has operated the brake pedal is input when the transmission control ECU has determined the vehicle is traveling downhill, the control downshifts to generate optimal engine braking force.
The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the transmission control ECU to determine uphill or downhill travel.
| *a | Uphill | *b | Downhill |
| *c | Smaller | *d | Greater |
|
Reference Acceleration |
|
Actual Acceleration |
Flex Lock-up Control
In order to improve the transmission efficiency and also the fuel economy, the linear solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.
The flex lock-up control consists of flex start control and flex lock-up control during deceleration.
The flex start control aggressively operates the lock-up clutch during start-off to increase the transmission efficiency. As a result, the engine can run in its most efficient operating range.
Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.
Clutch Capacity Control
When driving in belt mode, and sudden braking causes excessive input forces from the road surface, the C2 clutch performs torque capacity control to protect the belt by limiting the load applied to it. The hydraulic pressure pressing on the belt is reduced to match the torque capacity of the C2 clutch, and the reduced load on the oil pump contributes to fuel economy improvements.
FUNCTION
Snow Mode Select
Controls the drive force according to accelerator pedal operation to make smooth starting off possible on slippery surfaces such as snow-covered roads.
FAIL-SAFE
This function minimizes the loss of operability when a malfunction occurs in any sensor or shift solenoid valve.
For details, refer to the Repair Manual.
DIAGNOSIS
When the transmission control ECU detects a malfunction, it records the malfunction and information related to the fault. Furthermore, the transmission control ECU will illuminate the Malfunction Indicator Light (MIL) in the combination meter to inform the driver.
At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.